Table of Contents
Advertisement
Quick Links
Electric Chainsaw Sharpener
With Hydraulic Assist
Owner's Manual
WARNING:
Read carefully and understand all ASSEMBLY AND OPERATION
INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety
precautions may result in serious personal injury.
Item #57522
READ & SAVE THESE INSTRUCTIONS
Advertisement
Table of Contents
Related Manuals for Strongway 57522
Summary of Contents for Strongway 57522
- Page 1 With Hydraulic Assist Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. Item #57522 READ & SAVE THESE INSTRUCTIONS...
- Page 2 Thank you very much for choosing a Strongway™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it.
-
Page 3: Table Of Contents
Table of Contents Intended Use ............................4 Technical Specifications ........................4 Important Safety Information ....................... 4 Specific Operation Warnings ....................... 6 Grounding .............................. 6 Extension Cords ............................ 7 Main Parts of Sharpener ........................8 Assembly Instructions .......................... 8 Before Each Use ..........................10 Operating Instructions ........................ -
Page 4: Intended Use
Intended Use The Strongway Electric Chainsaw Sharpener with Hydraulic Assist is designed for sharpening most chainsaws. Technical Specifications Property Specification Supply voltage 110 Volt/60 Hz Motor input power 2.7 Amps (300 Watts) Chain Pitch ¼ Inch to ¾ Inch Maximum speed... - Page 5 and contact will cause electrical shock. • Keep children and bystanders away from the work area while operating the tool. Do not allow children to handle the product. ⚠WARNING PERSONAL SAFETY • Stay alert, watch what you are doing, and use common sense when operating the tool. Do not use the tool while you are tired or under the influence of drugs, alcohol, or medication.
-
Page 6: Specific Operation Warnings
another tool. Never use an accessory that has a lower operating speed or operating pressure than the tool itself. • Keep guards in place and in working order. Never operate the product without the guards in place. • Do not leave the tool running unattended. Specific Operation Warnings ⚠WARNING •... -
Page 7: Extension Cords
Tools marked with Grounding Required have a 3-wire cord and 3-prong grounding plug. The plug must be connected to a properly grounded outlet. If the tool should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user, reducing the risk of electric shock. -
Page 8: Main Parts Of Sharpener
• As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. • The smaller the wire’s gauge number, the greater the capacity of the cord. - Page 9 1. When installing it on a bench, place the sharpener on the edge of the bench to the stop (Fig. 1) and screw it to the desk using the holes in the base. 2. When mounting on the wall, use the respective holes in the vertical part of the base. 3.
-
Page 10: Before Each Use
7. To be able to install the disc, it is necessary to unscrew the auxiliary flange (Fig.6). Before Each Use ⚠WARNING • Inspect the whole condition of the sharpener for good working condition. • Check the disc you are about to use for damages prior to installation. Operating Instructions ⚠WARNING •... - Page 11 • When using the sharpener outdoors, always use an outdoor rated extension cord with a splash- proof plug and socket. • Do not use a caustic solution to clean plastic parts. • Do not use the sharpener in the proximity of flammable liquids and vapors. •...
-
Page 12: After Each Use
As always, be careful while working. Grinding 1. With the clamping screw adjusted, the vise angle set up (Note: RH and LH teeth to be differentiated), and the top plate angle preset, lower the grinding disc to the tooth. The grinding depth may reset by adjusting the set screw (K). -
Page 13: Maintenance
Maintenance Maintain the sharpener by adopting a program of conscientious repair and maintenance in accordance with the following recommended procedures. It is recommended that the general condition of any tool be examined before it is used. Keep your tool in good repair. Keep all cutting tools sharp and clean. - Page 14 Circuit breaker check 1.Unplug the power, use an insulating rod insert overload protector reset hole (less than φ5mm) and press to reset. 2.Plug in the power cord and turn on the green switch button, if the LED is light on status it means the chainsaw sharpener works again.
-
Page 15: Parts Diagram
Parts Diagram Parts List Reference Part Description Quantity Handle Hex Nut M6 Motor Holder Switch Adjusting Bolt M8 Adjusting Nut M8 Rubber MatM8 Big Tensional Spring Shaft Sleeve Shaft Stand Base Flat Washing 11*28*2.5 Tightening Knob Fixed Disc Page 15 of 19... - Page 16 Reference Part Description Quantity Hex Screw M5*22 Small Pressure Spring A Flat Washing 5*1 Hex Nut M5*22 Guide Wheel A Rubber Mat M6 Adjusting Nut M6 Adjusting Screw M6 Out Plate Inner Plate Steel Ball 4 Small Pressure Spring C Flat Mat 5*15*1 Dial Bottom Bolt M5*10...
-
Page 17: Replacement Parts
Replacement Parts • For replacement parts and technical questions, please call Customer Service at 1-800-222-5381. • Not all product components are available for replacement. The illustrations provided are a convenient reference to the location and position of parts in the assembly sequence. •... -
Page 18: Limited Warranty
Northern Tool and Equipment Company, Inc. ("We'' or "Us'') warrants to the original purchaser only ("You'' or "Your") that the Strongway product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. - Page 19 Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.com Made in China. Page 19 of 19...