Operation Parameters - Immergas MAGIS M4-30 Use And Installation

13.3

OPERATION PARAMETERS.

This manual is intended for the installer or service engineer controlling the operating parameters.
• On the main screen, go to MENU>OPERATION PARAMETER.
• Press OK. There are nine pages of operation parameters, as indicated below. Press
• Press and to check the operation parameters of the slave units in the cascade system. The code of the address in the
top right corner changes from "#00" to "#01", "#02", etc. Therefore:
OPERATION PARAMETER PARAMETRI DI FUNZIONAMENTO #00
NUMERO UNITÀ ONLINE ONLINE UNITS NUMBER
MODO FUNZIONAMENTO OPERATE MODE
SV1 STATE STATO SV1
STATO SV2
SV2 STATE
STATO SV3 SV3 STATE
POMP_I
PUMP_I
INDIR.
ADDRESS
OPERATION PARAMETER PARAMETRI DI FUNZIONAMENTO #00
T5 TEMP. ACQUA ACC. ACS T5 WATER TANK TEMP.
Tw2 CIRCUIT2 WATER TEMP. Tw2 TEMP. ACQUA CIRCUIT2
TIS' C1 CLI. CURVE TEMP. T1S' C1 TEMP. CURVA CLIM.
T1S2' C2 TEMP. CURVA CLIM.
TIS2' C2 CLI. CURVE TEMP.
TW_O TEMP. ACQUA OUT SP
TW_O PLATE W-OUTLET TEMP.
TW_I TEMP. ACQUA IN SP
TW_I PLATE W-INLET TEMP.
INDIR. ADDRESS
OPERATION PARAMETER
PARAMETRI DI FUNZIONAMENTO #00
FAN SPEED VELOC. VENTIL.
IDU TARGET FREQUENCY FREQUEN. IDEALE IDU
TIPO LIMITE FREQ.
FREQUENCY LIMITED TYPE
TENSIONE ALIMENTAZIONE SUPPLY VOLTAGE
TENSIONE GENER. CC
DC GENERATRIX VOLTAGE
DC GENERATRIX CURRENT ALIM. GENERATORE CC
INDIR. ADDRESS
NOTE
Entering the power consumption parameter is optional. Parameters not activated in the system are marked "--".
The capacity of the heat pump is for reference only, it is not used to assess the capacity of the unit. Sensor accuracy is
±1°C. The flow rate parameters are calculated based on the operation parameters of the pump, the deviation is different
at different flow rates, the maximum deviation is 15%. The flow rate parameters are calculated based on the electric
operation parameters of the pump.
The operating voltage and deviation are different.
The value displayed is 0 when voltage is lower than 198V.
PARAMETRI DI FUNZIONAMENTO #00 OPERATION PARAMETER
1 PUMP_O
POMP_O
FREDDO COOL PUMP_C POMP_C
ON ON PUMP_S POMP_S
OFF OFF POMP_D PUMP_D
OFF OFF RISC. RISER. TUBO PIPE BACKUP HEATER
ON NO
RISC. RISER. SERB. TANK BACKUP HEATER
INDIR.
ADDRESS
1/9
OPERATION PARAMETER PARAMETRI DI FUNZIONAMENTO #00
53°C Tbt1 TEMP. SERBSUPP_ALT. Tbt1 BUFFERTANK_UP TEMP.
35°C Tbt2 BUFFERTANK_LOW TEMP. Tbt2 TEMP. SERBSUPP_BAS.
35°C Tsolar
35°C SOFTWARE IDU
IDU SOFTWARE
35°C
30°C
INDIR.
ADDRESS
4/9
OPERATION PARAMETER PARAMETRI DI FUNZIONAMENTO #00
TW_O PLATE W-OUTLET TEMP. TW_O TEMP. ACQUA OUT SP
600 GIRI /MIN 600R/MIN
46Hz
46Hz TW_I TEMP. ACQUA IN SP TW_I PLATE W-INLET TEMP.
5 T2 TEMP. REFR. USCITA SP
T2 PLATE F-OUT TEMP.
T2B TEMP. REFR. IN SP T2B PLATE F-IN TEMP.
230V 230V
420V COMP. Th TEMP. DI ASPIRAZIONE 5°C Th COMP. SUCTION TEMP.
420V
COMP. Tp TEMP. DI SCARICO Tp COMP. DISCHARGE TEMP.
18A 18A
INDIR. ADDRESS
7/9
OPERATION PARAMETER
PARAMETRI DI FUNZIONAMENTO #00
BOILER GAS GAS BOILER
OFF OFF
T1 LEAVING WATER TEMP.
T1 TEMP. ACQUA USCITA
OFF OFF
FLUSSO ACQUA WATER FLOW
OFF OFF
CAPAC. POM. CALORE
HEAT PUMP CAPACTIY
OFF OFF
CONSUMO ENER. POWER CONSUM
OFF
OFF
Ta ROOM TEMP.
Ta TEM. AMB.
ON ON
2/9
OPERATION PARAMETER PARAMETRI DI FUNZIONAMENTO #00
35°C MOD. ODU ODU MODEL
35°C COMP.CURRENT CORR. COMP.
25°C COMP.FREQUENCY FREQ. COMP.
01-09-2019V01 TEM. AT.COMP.
COMP.RUN TIME
COMP.TOTAL RUN TIME TEM. AT. TOT. COMP.
EXPANSION VALVE APERTURA VALV. ESPANS.
INDIR. ADDRESS
5/9
OPERATION PARAMETER PARAMETRI DI FUNZIONAMENTO #00
35°C
T3 TEMP. SCARICO EST. T3 OUTDOOR EXCHARGE TEMP.
30°C
T4 TEMP. ARIA ESTERNA T4 OUTDOOR AIR TEMP.
35°C
TF MODULE TEMP. TEMP. MODULO TF
35°C
P1 COMP. PRESSIONE P1 COMP. PRESSURE
ODU SOFTWARE SOFTWARE ODU
75°C
SOFTWARE HMI HMI SOFTWARE
INDIR.
8/9 ADDRESS
124
and to scroll through them.
35°C
1.72m
1,72m
11.52kW
11,52kW
1000kWh
1000kWh
25°C
INDIR.
ADDRESS
3/9
24Hz
54 MIN
54 MIN
1000Hrs
1000Hrs
200P
6/9
2300kPa
2300kPa
01-09-2018V01
01-09-2018V01
9/9
OFF OFF
3 3 /h
/h
6kW
6kW
12A 12A
24Hz
5°C
5°C
55°C