Anker Soundcore Flare Manual

Safety Instructions

• Avoid dropping.
• Do not disassemble.
• Soundcore Flare can be immersed in water up to 1m for up to 30 minutes.
• Avoid extreme temperatures.
• Do not use the device outdoors during thunderstorms.
• Use original or certified cables.
• Do not use any corrosive cleaner/oil to clean.

What's Included

At a Glance

1. Volume Buttons for Volume Control
2. Bass Up Button
3. Multi-function Button
4. Light Effects Button
5. Bluetooth Button
6. Power Button
7. 3.5mm Audio Input Port
8. micro USB Port

Using Your Soundcore Flare

1. Turn on / off
   
   1. Bluetooth mode
      
      
      

      	Flashing White	Bluetooth Pairing Mode
      	Solid White	Connected to a device
      		Enter True Wireless Stereo Pairing Mode / Disconnect True Wireless Stereo
      	Double Flashing White	True Wireless Stereo Pairing Mode
      	Solid White	Connected to True Wireless Stereo Note: Once connected, the status indicator will stay white for 5 seconds.

      
      
      With True Wireless Stereo technology, you can pair your Soundcore Flare with another Bluetooth speaker (Soundcore Flare) to explore the best sound effects with left and right sound channels separated on both speakers.

      	Play / Pause
      	Play Next Song
      	Play Previous Song
      	Press to turn Bass Up on and off
      	Press and hold for 2 seconds to reset EQ settings
      	Answer Call / End Call
      	Reject Call / Switch between a call on hold and an active call
      	End current call and answer incoming call / End current call and switch to call on hold
      	Switch audio source between Speaker and Phone
      	Put current call on hold and answer incoming call
      	Activate Siri / Other Voice Control Software
      	Volume Up / Down
      	Solid White	On a Call
      	Flashing White	Incoming Call
      	Press and hold for 2 seconds to turn Light Effects Off
      	Press to turn Light Effects On
      	Press once to switch between Light Effect modes

      
      When turned on, Soundcore Flare will automatically connect to the last connected device if available. If not, press the Bluetooth pairing button to activate pairing mode.
      To pair a different device, press the Bluetooth button to re-enter pairing mode. Then repeat the pairing steps.
      Having connection problems? Remove Soundcore Flare from your device's Bluetooth history and ensure it's less than 3 feet away. Then try pairing again. To get the best sound quality, make sure there is a clear line of sight between the connected device and your speaker.
   2. AUX-In mode
      
      * SoundLine AUX cable sold separately.
      
      Plugging in an audio cable will automatically switch to AUX mode. When using AUX mode, control audio playback via the connected device.

Charging your Soundcore Flare

	Slow Flashing Red	Low Battery
	Solid Red	Charging
		Fully Charged

Use the included USB cable to charge your Soundcore Flare and make sure it is fully charged before its first use.

Disconnect your speaker from the charger when fully charged. Do not charge your speaker for extended periods.

When not in use, store your speaker in a cool place.

Specifications

Specifications are subject to change without notice.

Input: 5 V ⎓ 2 A
Audio output: 6 W x 2
Battery capacity: 4400 mAh
Charging time: 3.5 hours
Play time (varies by volume level and music content): 12 hours
Size: 89 x 89 x 151 mm / 3.5 x 3.5 x 5.95 in
Weight (without packaging): 530 g / 18.7 oz
Bluetooth version: V4.2 + EDR
Range: 20 m / 66 ft

Soundcore App

• Light effect
• Update firmware
• Wave Equalizer
• Stereo or Boost mode
• Rename
• More

Videos

Anker Soundcore Flare Review Video

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Anker Soundcore Flare Manual