Table of Contents
Advertisement
Quick Links
1
Introduction
Use this document for quick installation and setup.
Teledyne LeCroy's PCI Express 5.0 U.2/U.3 Interposer provides a quick and simple means for protocol analysis of Solid
State Drives (SSDs) based on PCI Express (PCIe
Protocol Analyzer, enables PCIe bus traffic between a host backplane and SSD device to be monitored, captured, and
recorded for protocol analysis. The card is compatible with the Summit T516 and Summit T54 and supports data rates
of 2.5 GT/s, 5.0 GT/s, 8.0 GT/s, 16.0 GT/s and 32 GT/s. The interposer supports side band signals such as PERST#,
WAKE#, CLKREQ# and SMBus (SMBCLK, SMBDAT). The interposer can be used with Single x4 Port or Dual x2 Ports.
It also supports U.2 and U.3 standards. It can be used also with Summit T4 and Summit M5x analyzers using a
conversion cable.
2
Components
The interposer package includes the following components:
•
PCI Express 5.0 U.2/U.3 Interposer
•
3.5 Inch conversion bracket kit
•
Support bracket extension and screws
•
DC Power Adapter (+12V @ 5A)
•
User Manual and Quick Start Guide (this document)
Inspect the received shipping container for any damage. Unpack the container and account for each of the system
components listed on the accompanying packing list. Visually inspect each component for absence of damage. In the
event of damage, notify the shipper and Teledyne LeCroy. Retain all shipping materials for shipper's inspection.
PCI Express
User Manual and Quick Start Guide
®
) protocols. The U.2/U.3 Interposer Card, used with a Summit
PCI Express 5.0 U.2/U.3 Interposer
®
5.0 U.2/U.3 Interposer
Advertisement
Table of Contents
Related Manuals for Teledyne Lecroy PCI Express 5.0 U.2
Summary of Contents for Teledyne Lecroy PCI Express 5.0 U.2
- Page 1 User Manual and Quick Start Guide Introduction Use this document for quick installation and setup. Teledyne LeCroy’s PCI Express 5.0 U.2/U.3 Interposer provides a quick and simple means for protocol analysis of Solid ® State Drives (SSDs) based on PCI Express (PCIe ) protocols.
-
Page 2: Clock Selection
Clock Selection The source for the reference clock used by the analyzer to record PCI Express traffic is configurable according to below table. DIP switches and tables for clock selection are located on the rear side of the interposer. SW2: Clock Select SW2: Clock Select Port B Port A... - Page 3 Screw the drive to the bay to secure it. 4. Install the Interposer into the host system connector. 5. Connect the Summit T516 Analyzer (or other compatible Teledyne LeCroy analyzer) to the interposer using the appropriate analyzer cable (PE028UCA-X Y-cable or PE027UCA-X straight cable). ...
- Page 4 Connecting the PCI Express 5.0 U.2/U.3 Interposer to one Summit T516 Analyzer U.2 Host Slot Summit T516 Analyzer Attach support bracket for 3.5 Inch conversion (optional) and drive carrier (required). See sections 7 and 8 Analyzer Y cable: below. PE028UCA-X...
- Page 5 Sideband Header Pinout Table 1: J28 Sideband Header Header Pin Number Sideband Signal Name J28-1 WAKE# J28-2 IFDET#2 J28-3 CLKREQ# J28-4 HPT0 J28-5 IFDET# J28-6 HPT1 J28-7 PRSNT# J28-8 SMCLK J28-9 ACTIVITY# J28-10 SMDAT J28-11 PCIEB_RST# J28-12 DUALPORTEN# J28-13 PCIEA_RST# J28-14 DEV_RESET J28-15...
-
Page 6: Drive Carrier
INTERPOSER. Teledyne LeCroy's PCI Express 5.0 U.2/U.3 Interposer can be attached to a donor drive carrier. If you plan to insert the interposer into a Chassis backplane you MUST fit the rails from a donor carrier to the interposer before use, to avoid serious damage to the interposer. - Page 7 Step 1. Remove the Drive Carrier from the Server Backplane To remove the drive carrier from the server backplane, squeeze the two levers together on the front of the carrier and while gripping the handle provided on the front of the carrier slowly pull the drive carrier out of the server backplane. Set the drive carrier on a suitable work surface (workbench with ESD pad or similar surface).
- Page 8 Step 4. Remove the Corner of the Side Rail After Removal from Drive Carrier Using a suitable cutting tool (diagonal cutting pliers, etc) remove the corners of the side rails. Typical set of Cut along the corner diagonal of the side rail cutting pliers (or similar tool) Step 5.
- Page 9 Step 6. Bend Drive Carrier Ears Out of the Way The drive carrier is usually a simple folded piece of fairly thin metal, which can be gently bent flat by hand. If there are metal ears, which held the screws to the ejection catch assembly, they should be gently (by hand) unfolded first before the end of the drive carrier metal is unfolded.
- Page 10 Step 9. Attach the PCI Express 5.0 U.2/U.3 Interposer to the Drive Carrier Slide the Interposer into the drive carrier, using the original mounting screws to hold it in place. The Interposer should be aligned with the same holes the drive carrier would have used. Note: Screw type for use with Drive Carrier: Metric screw, size M3, maximum length: 8mm.
- Page 11 Support Bracket for 3.5 Inch Conversion To support and stabilize the PCI Express 5.0 U.2/U.3 Interposer within a 3.5" drive carrier, Teledyne LeCroy supplies a bracket kit. The bracket can be mounted on either the top or bottom of the Interposer, depending on the drive carrier configuration.
-
Page 12: Environmental Conditions
Product specifications are subject to change without notice. Summit T516, Summit T54, Summit T416, Summit T48 are Teledyne LeCroy reserves the right to revise the information in this trademarks of Teledyne LeCroy. All other trademarks are property document without notice or penalty.