Page 1
User manual In the box Clearing blockages from your Getting started Mini motorised tool Caring for your floors Clearing blockages from your Charging your machine Hair screw tool Emptying your bin Washing your filter Cleaning your bin Washing your Fluffy™ brush bars Clearing blockages Cleaning your tools Clearing obstructions from your...
Page 2
You can buy additional tools at www.dyson.com.au or www.dyson.co.nz Low-reach adaptor Extension hose Stubborn dirt brush Bends to comfortably Flexi crevice tool...
Getting started Power modes The right power when you need it. Three modes to choose from, to suit any task on any floor type. Maximum suction Intensive cleaning for ground-in dirt. Suction mode 2 The optimum balance of power and run time. Suction mode 1 Maximum run time for longer cleans.
Page 4
Caring for your floors Check that the underside of the cleaner head or tool is clean and free from any objects that may cause damage. Before vacuuming your flooring, rugs, and carpets, check the manufacturer’s recommended cleaning instructions. The brush bar on your machine can damage certain carpet types and floors. Some carpets will fuzz if a rotating brush bar is used when vacuuming.
Page 5
Emptying your bin Empty as soon as the dirt reaches the MAX level – don’t overfill. Using your machine when the dirt is above the MAX line may affect the performance and require more frequent filter washing. Remove your wand Press the red wand release button, on the top of the wand, and pull the wand away from the bin.
Cleaning your bin Remove your bin If it is necessary to clean your bin, empty it as shown in the ‘Emptying your bin’ section. Press the red button located on the bin runner to release the bin and slide your bin off the runner. Only use a damp, lint-free cloth to clean your bin.
Page 7
Clearing obstructions from your Motorbar™ cleaner head Your Motorbar™ cleaner head doesn't have a washable brush bar. To maintain optimum performance, check your brush bar regularly and clear any obstructions. Make sure your machine is disconnected from the charger and take care not to touch the trigger.
Page 8
Clearing blockages from your Mini motorised tool Mini Motorised tool may not be included in box. Your Mini motorised tool doesn’t have a washable brush bar. To maintain optimum performance, check your brush bar regularly and clear any obstructions. Make sure your machine is disconnected from the charger and take care not to touch the trigger.
Page 9
Clearing blockages from your Hair screw tool Hair screw tool may not be included in box. Your Hair screw tool doesn't have a washable brush bar. To maintain optimum performance, check your brush bar regularly and clear any obstructions. Make sure your machine is disconnected from the charger and take care not to touch the trigger.
Page 10
The filter LED will illuminate on the top of your battery when the filter needs cleaning. This LED will flash if the filter isn't fitted correctly. For more information and support videos for your machine go online: www.dyson.com/support Twist off your filter Twist your filter anti-clockwise and pull it away from your machine.
Page 11
Washing your Fluffy™ brush bars Fluffy brushbar may not be included in box. Your machine has two washable brush bars. To maintain optimum performance, check and wash your brush bars regularly. Make sure your machine is disconnected from the charger and take care not to touch the trigger.
Page 12
Before replacing, check that your brush bars are completely dry. Refit your small brush bar first, insert the round end into place and then push down the octagonal end until it clicks into place. Reattach the end cap to your main brush bar. Slide your main brush bar into the cleaner head.
Page 13
Cleaning your tools Don’t put any part of your machine in a dishwasher or use detergents, polishes or air fresheners. Wipe with a damp, lint-free cloth, without touching the connector end. Make sure your tools are completely dry before using. Some tools may not be included in the box.
Page 14
Your machine won’t operate or charge if the ambient temperature is below 5°C (41°F). This is designed to protect both the motor and battery. Diagnostic lights If you see a diagnostic light on your machine, call Dyson for assistance. Battery fault. Main body fault.