IL PRESENTE FOGLIO È DA LASCIARE ALL'UTENTE ABBINATO AL LIBRETTO ISTRUZIONI DEL PRODOTTO FINITO AVVERTENZE GENERALI. L’installazione o il montaggio improprio dell’ a pparecchio e/o dei Tutti i prodotti Immergas sono protetti con idoneo imballaggio componenti, accessori, kit e dispositivi Immergas potrebbe dare da trasporto.
Il telaio nella sua parte inferiore è dotato dei fori necessari per razione (solo per installazione “tipo C”) mediante l’utilizzo di gli allacciamenti idraulici, gas, elettrici, scarico condensa e per fumisteria marcata Immergas. il collegamento della termoregolazione. DIMENSIONI PRINCIPALI. ATTENZIONE Con il kit concentrico 60 / 100 utilizzare la foratura D.
Page 4
DIMA ALLACCIAMENTO. ALLACCIAMENTO ACC. INERZIALE (Per dettagli quote vedi fig.1) ALLACCIAMENTO POSTERIORE ALLACCIAMENTO INFERIORE ALLACCIAMENTO LATERALE DESTRO Legenda: G - Alimentazione gas AC - Uscita acqua calda sanitario AF - Entrata acqua sanitario LP - Linea frigorifera - stato liquido GP - Linea frigorifera - stato gassoso LP2 - Linea frigorifera - stato liquido* GP2 - Linea frigorifera - stato gassoso*...
INSTALLAZIONE: N.B.: Il gruppo di allacciamento non è a corredo, ma venduto Predisporre le opere murarie creando un'apertura nella parete separatamente (optional). Per facilitare l’installazione è possi- dove verrà installato il telaio (1), facendo attenzione a preve- bile scegliere se operare l’allacciamento nella parte posteriore, dere lo spazio per i sei spacchi per inserire le rispettive alette nella parte inferiore o laterale (in basso a destra) del kit Solar di sostegno (2) e uno spazio sotto il telaio sufficiente per poter...
Page 6
Legenda disegni installazione: Identificazione univoca componente Identificazione sequenziale operazione da svolgere Identificazione componente generico o non fornito in dotazione Fig. 3...
This instruction manual provides technical information for Installation and maintenance must be performed in compliance installing the Immergas kit. As for the other issues related to kit with the regulations in force, according to the manufacturer's in- installation (e.g. safety at the workplace, environmental protection,...
“C type” installations) and to the intake duct (only for “C space for the Magis Combo Plus in external and internal walls. type” installation) using the Immergas flue. The lower part of the frame has the holes necessary for the hydraulic, gas, electrical, condensate drain and temperature control connections.
Page 10
CONNECTION TEMPLATE. INERTIAL STORAGE TANK CONNECTION (For details of values see fig.1) REAR CONNECTION FLOW AND RETURN FOR INERTIAL STORAGE TANK LOWER CONNECTION RIGHT HAND SIDE CONNECTION Key: G - Gas supply AC - Domestic hot water outlet AF - DHW (Domestic hot water) water inlet LP - Chiller line - liquid phase GP - Chiller line - gaseous phase LP2 - Chiller line - liquid phase*...
INSTALLATION: N.B.: The connection unit is not supplied, but is sold separately Set-up the masonry jobs creating an opening in the wall where (optional). To ease installation, choose whether to make the the frame will be installed (1), paying attention to envision the connection at the rear, bottom or side (bottom right) of the Solar space for the six slots for inserting the respective support fins Container Combo kit (see Fig.
Page 12
Drawings key installation: Unambiguous component identification Sequential identification of the operation to perform Identification of generic or not supplied component Fig. 3...
Page 16
Per richiedere ulteriori approfondimenti specifici, i Professionisti del settore possono anche avvalersi dell’indirizzo e-mail: consulenza@immergas.com To request further specific details, sector Professionals can also use the following e-mail address: consulenza@immergas.com Immergas S.p.A. 42041 Brescello (RE) - Italy Tel. 0522.689011 Fax 0522.680617...