Page 1
GAS POWERED POLESAW/PRUNER 1 HP Model 95283 ASSEMBLY AND OPERATING INSTRUCTIONS Do to continuing improvements, actual product may differ slightly from the product described herein. CAUTION! Your Warranty Is Voided If: You do not operate the Polesaw/Pruner with the proper 50:1 fuel mix in its fuel tank.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create SKU 95283 For technical questions, please call 1-800-444-3353 Description 1 HP / 26cc / Single Cylinder / 2-Stroke Fuel Required: 50:1 Unleaded Fuel &...
Maintain tools with care. Properly maintained tools are less likely to malfunction and are easier to control. Do not use a damaged tool. Tag damaged tools “Do not use” until repaired. SKU 95283 For technical questions, please call 1-800-444-3353 PERSONAL SAFETY...
Never leave the Polesaw/Pruner unattended when it is running. Turn off the Engine before leaving. Never allow children in the work area with the danger of falling debris and a power tool in operation. SKU 95283 For technical questions, please call 1-800-444-3353 SERVICE PAGE 4...
A. Make sure the area in which you are cutting is free from obstructions. Do SKU 95283 For technical questions, please call 1-800-444-3353 KICKBACK PRECAUTIONS...
Use proper fuel storage and handling procedures. Always have multiple ABC class fire extinguishers nearby. Keep the Polesaw/Pruner and surrounding areas clean at all times. When spills of fuel or oil occur, they must be cleaned up immediately. SKU 95283 For technical questions, please call 1-800-444-3353 PAGE 6...
For eye contact, immediately flush eyes with clean water. Prolonged exposure to high noise levels is hazardous to hearing. Always wear ANSI approved hearing protection when operating or working SKU 95283 For technical questions, please call 1-800-444-3353 CHEMICAL PRECAUTIONS...
Insert the lower section of the Top Pipe Support (33) into the Connector (22). Then secure the Top Pipe Support to the Connector by firmly tightening the Wing Nut (31). (See Figure A.) TOP PIPE SUPPORT (33) FIGURE A SKU 95283 For technical questions, please call 1-800-444-3353 MISC. PRECAUTIONS UNPACKING GEAR BOX (61)
Wing Nut (31): Prior to each use of the Polesaw/Pruner, make sure the Wing Nut is firmly tightened in order to properly secure the Top Pipe Support (33) to the unit. (See Figure B.) SKU 95283 For technical questions, please call 1-800-444-3353 PRODUCT FEATURES...
Page 10
IMPORTANT: The cutters on the top of the Guard Bar should face toward the Guard Bar tip, in the direction of the chain rotation. (See Figure B.) SKU 95283 For technical questions, please call 1-800-444-3353 until sag does not exist. Then, retighten the...
Prior to each use of the Polesaw/Pruner, the Chain Oil Tank (69) must be filled with S.A.E. 30 weight oil (below 34 Fahrenheit) or S.A.E. 40 weight oil (above 75 Fahrenheit). (See Figure B.) SKU 95283 For technical questions, please call 1-800-444-3353 PAGE 11...
Page 12
Set the Choke Lever (48A) to the appropriate position: A. “START” if the Engine (1) is cold. (See Figure B.) B. “RUN” if the Engine (1) is warm. (See Figure B.) SKU 95283 For technical questions, please call 1-800-444-3353 (See Figure B.)
Page 13
Let up on the Throttle Lever (8). Then turn the Power Switch (10) to its “OFF” position. (See Figure B.) To Operate The Polesaw/Pruner: Maintain a proper grip on the Polesaw/Pruner whenever the Engine (1) is SKU 95283 For technical questions, please call 1-800-444-3353 PAGE 13...
Page 14
Engine parts (ignition system, piston rings, carburetor, etc.) from being damaged by overheating. Then turn the Power Switch (10) to its “OFF” position. (See Figure B.) SKU 95283 For technical questions, please call 1-800-444-3353 FIGURE D PAGE 14...
Bar stud. The Guard Bar also has two chain tensioning pin holes which fit over the chain tensioning pins. Place the Guard Bar onto the bar stud so that the chain tensioning pins fit into the chain tensioning pin holes. Fit the Chain over SKU 95283 For technical questions, please call 1-800-444-3353 PAGE 15...
Page 16
CHAIN GUARD BAR (74) (75) (73) DRIVE GEAR (44) GUARD BAR (73) GUARD BAR STUD CHAIN TENSIONING SKU 95283 For technical questions, please call 1-800-444-3353 CHAIN SAW COVER (77) CHAIN TENSION ASSY. (38) (75) CHAIN (74) GUARD BAR STUD...
ASSUMES ALL RISKS AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 95283 For technical questions, please call 1-800-444-3353 TROUBLESHOOTING Possible Cause 1.
Page 18
Chain Tension Adjusting Screw 81 Screw Bearing Drive Gear Axis Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 95283 For technical questions, please call 1-800-444-3353 Part # Description Washer Drive Gear...
Page 19
ASSEMBLY DIAGRAM - POLESAW/PRUNER UNIT 83: Hex Wrenches not shown. NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 95283 For technical questions, please call 1-800-444-3353 PAGE 19...
Air Filter Screw Set Choke Valve Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 95283 For technical questions, please call 1-800-444-3353 PARTS LIST - ENGINE Description Part # Air Filter Support...
Page 22
(d) improper or inadequate maintenance of any warranted parts (e) repairs performed outside of the authorized warranty service dealers alterations by changing, adding to or removing parts from the engine. SKU 95283 For technical questions, please call 1-800-444-3353 Manufacturer’s Warranty Coverage Owner’s Warranty Responsibilities...
Page 23
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353 SKU 95283 For technical questions, please call 1-800-444-3353...