Page 1
WALL MOUNT HALOGEN LAMP 500 WATTS Model 90401 ASSEMBLY AND OPERATING INSTRUCTIONS ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at: http://www.harborfreight.com Copyright 2003 by Harbor Freight Tools ® . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. SKU 90401 90401.p65 PRODUCT SPECIFICATIONS " 8 " 0 "...
Do not use a power tool while tired or under the influ- ence of drugs, alcohol, or medication. A moment of inattention while operat- ing power tools may result in serious personal injury. SKU 90401 90401.p65 ELECTRICAL SAFETY...
Page 4
Do not use a damaged tool. Tag damaged tools “Do not use” until repaired. SKU 90401 90401.p65 TOOL USE AND CARE PAGE 4...
The green wire in the cord must be the only wire connected to the tool’s grounding system and must never be attached to an electrically “live” terminal. (See Figure A.) SKU 90401 90401.p65 SERVICE...
Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. (See Figure B.) Double insulated tools may be used in either of the 120 volt outlets shown in the following illustration. (See Figure B.) SKU 90401 90401.p65 FIGURE A FIGURE B...
0 – 2.0 2.1 – 3.4 3.5 – 5.0 5.1 – 7.0 7.1 – 12.0 12.1 – 16.0 16.1 – 20.0 FIGURE C SKU 90401 90401.p65 EXTENSION CORDS (120 VOLT) EXTENSION CORD LENGTH Feet Feet Feet * Based on limiting the line voltage drop to five volts at 150% of the rated amperes.
(part #13) becomes VERY hot. While operating this product, do not touch the Halogen Bulb, its Guard or Enclosure. Avoid excessive UV radiation. Should your skin begin to feel hot while operat- ing the Halogen Lamp, remove yourself from its light rays. SKU 90401 90401.p65 SYMBOLOGY Double Insulated...
Page 9
NOTE: For additional information regarding the parts mentioned in the following pages, refer to the Assembly Diagram on page 14. WARNING! Make sure the wall to which the Halogen Lamp will be attached is capable of supporting the full weight of the Lamp. SKU 90401 90401.p65 UNPACKING ASSEMBLY INSTRUCTIONS...
Page 10
Once the Halogen Lamp is fully assembled, you may aim the Lamp by loosening the phillips Screw on each side of the Lamp. Tilt the Lamp to the desired posi- tion. Then, re-tighten the phillips Screws. (See Figure G, next page.) SKU 90401 90401.p65 BOLT...
Socket and remove the opposite end. Reverse this procedure to install a new Bulb. NOTE: Do not touch the new Bulb with your fingers, as oil in your skin will cause damage to the Bulb. (See Figure H.) FIGURE H SKU 90401 90401.p65 OPERATING INSTRUCTIONS SCREW...
PLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACE- MENT PARTS THERETO. n i t NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 90401 90401.p65 PARTS LIST t l o PAGE 13...
NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 90401 90401.p65 ASSEMBLY DIAGRAM 14: POWER CORD NOT SHOWN. PAGE 14 8/15/2003, 9:37 AM...