Page 1 Product names mentioned herein may be trademarks and/or registered trademarks of their respective companies. EFERENCE UIDE Armada 7300 Family of Personal Computers Second Edition November 1997 First Edition June 1997 Part Number 247738-002 Compaq Computer Corporation...
Page 2: Table Of Contents
ONTENTS preface SING UIDE chapter 1 ETTING TARTED Unpacking the Computer ...1-2 Taking the Battery Pack Out of Ship Mode...1-3 Setting Up the Computer...1-4 Setting Up the Software ...1-7 Where to Go from Here...1-9 Registering the Computer ...1-9 Backing Up the System...1-9 Finding Online Help ...1-10 Customizing Computer Settings ...1-10 Finding Optional Equipment ...1-10...
Page 3 chapter 3 SING THE EYBOARD AND Using the Pointing Device and Mouse Buttons... 3-1 Changing Mouse Settings... 3-2 Identifying Keyboard Components ... 3-2 Hotkeys ... 3-3 Embedded Numeric Keypad... 3-4 Programmable Keys... 3-4 Opening the Programmable Keys Dialog Box... 3-4 Assigning Programmable Keys ...
Page 4 Inserting a Hard Drive into the Hard Drive Bay ...6-6 Using MultiBay Adapters ...6-8 Inserting a Hard Drive into the Armada 7300 Hard Drive MultiBay Adapter ...6-8 Removing/Inserting a Drive in the Armada 7000 Removable Drive MultiBay Adapter...6-9 Removing/Inserting Drives in the Computer MultiBay ...6-14 Removing a Drive from the Computer MultiBay...6-14...
Page 5 chapter 9 SING THE NFRARED Infrared Software ... 9-2 Infrared Monitor ... 9-2 Direct Cable Connection ... 9-2 Preparing for an Infrared Connection... 9-3 chapter 10 PC C SING ARDS Supported PC Cards... 10-1 Compaq PC Card Solutions List... 10-2 Configuring PC Cards...
Page 6 chapter 13 AINTENANCE AND RAVEL Routine Care...13-1 Replacing the Pointing Device Cap ...13-2 Traveling and Shipping Guidelines ...13-2 Air Travel...13-3 International Travel...13-3 Shipping ...13-4 chapter 14 ECURITY EATURES Software Security ...14-2 Establishing a Power-On Password ...14-2 Enabling QuickLock and QuickBlank...14-3 Establishing a Setup Password ...14-3 Changing or Deleting a Password ...14-4 Disabling Devices ...14-4...
Page 7 chapter 17 ROUBLESHOOTING Minor Problems Checklist ... 17-2 Solving Audio Problems... 17-3 Solving Battery and Battery Gauge Problems... 17-4 Solving Diskette and Diskette Drive Problems ... 17-7 Solving Hard Drive Problems... 17-9 Solving Hardware Problems ... 17-10 Solving Infrared Problems... 17-11 Solving Keyboard and Numeric Keypad Problems ...
Page 8 preface SING Some or all of the following format conventions are used in this guide to distinguish elements of text: Names of keys are shown in bold type as they appear on the keyboard, for example, Keys that you should press at the same time are represented by the key names and the plus (+) symbol, for example, Ctrl+Alt+Delete.
Page 10: Getting Started
chapter ETTING This chapter describes the steps (shown on the graphical poster) to set up the computer, and includes the following: Unpacking the computer and verifying that all items were received. Taking the battery pack out of ship mode so that it can be charged and used.
Page 11: Unpacking The Computer
Unpacking the Computer You should have the following items in the packing box: Computer with hard drive, diskette drive, battery pack, and preinstalled software (some models have an integrated modem) Slipcase Hard drive carrying case MultiBay device carrying case MultiBay weight saver (inside MultiBay device carrying case) AC Adapter Power cord Bag with two spare pointing device caps...
Page 12: Taking The Battery Pack Out Of Ship Mode
Taking the Battery Pack Out of Ship Mode When the computer is shipped from the factory, the battery pack in the battery bay is in ship mode. You must take the battery pack out of ship mode before the battery pack can be charged and used. Ship mode is used only when the computer is shipped from NOTE: the factory.
Page 13: Setting Up The Computer
4. With the label on the battery pack facing up and the battery contacts facing in, reinsert the battery pack into the battery bay until it clicks into place. Reinserting the Battery Pack into the Battery Bay Setting Up the Computer 1.
Page 14 Connecting the Computer to External Power WARNING: To reduce the risk of personal injury, electric shock, fire, or damage to the equipment: Do not disable the power cord grounding plug. The grounding plug is an important safety feature. Plug the equipment into a grounded (earthed) electrical outlet that is easily accessible at all times.
Page 15 3. Open the computer by sliding forward the release latch each side of the display and then raising the display comfortable viewing angle. Opening the Computer 4. If you prefer the back of the computer tilted up, swivel the tilt feet back and under the keyboard.
Page 16: Setting Up The Software
Setting Up the Software When you turn on the computer the first time, the Compaq setup screen appears. After you select to begin software setup, you must complete the entire process, which may require up to 20 minutes. The Windows operating system is selected on some models NOTE: at the time of purchase and on other models during software setup.
Page 17 2. Follow the instructions on the screen to complete the setup of the Windows operating system and the Compaq value-add software. 3. When prompted to select your language (and Windows operating system on some models), choose carefully. IMPORTANT: models) that you do not choose will be deleted and cannot be recovered.
Page 18: Where To Go From Here
Where to Go from Here Registering the Computer To protect your investment, be sure to follow the instructions to register your computer. Backing Up the System The hard drive preinstalled in your computer is partitioned into two or more logical drives, depending on the size of the hard drive.
Page 19: Finding Online Help
Finding Online Help To access the online Reference Guide: Click the Start button, point to Compaq Information Center, then click Reference Guide, or Click the Start button, then click Help. If you are new to the Windows operating system, double-click the introductory topics on the Help menu to get started quickly.
Page 20: Taking A Look At The Computer
chapter AKING A OMPUTER This chapter provides an overview of the computer features and components. Illustrations identify exterior components and give brief descriptions of their functions. Features Overview All models of the computer include the following features: Intel Mobile Pentium processor 64-bit EDO DRAM memory (expandable through memory upgrades) Level 2 cache memory...
Page 21: Exterior Components
Built-in speakers, microphone, and jacks for 16-bit stereo sound with electronic equalization and wave table synthesis Energy Star–compliant power saving features Ports and connectors for external equipment, including serial, parallel, external monitor, and an external PS/2-compatible pointing device or keyboard Desktop functionality with the optional ArmadaStation expansion base or the Armada MiniStation convenience bases Some models include an integrated modem and/or a CD-ROM...
Page 22 Component Display switch Volume control buttons Suspend button Caps lock light Scroll lock light Num lock light Power switch Stereo speakers (2) MultiBay drive light Battery light Hard drive light Power/suspend light Left and right mouse buttons* Easy Point III pointing device* Programmable keys* *For more information about keyboard components, see Chapter 3,...
Page 23: Front And Right Side Components
Front and Right Side Components Front and Right Side Components Front and Right Side Components Component Microphone Battery bay MultiBay Stereo line-in jack Stereo speaker/ headphone jack Microphone jack Modem 25-pin connector 2-4 Taking a Look at the Computer Function Located on the inside and outside of the display;...
Page 24 Front and Right Side Components Component Security cable slot Modem RJ-11 jack (not on models sold in Europe or Australia) CardBus slots PC Card eject buttons Tilt feet (2) Continued Function Attach an optional security cable to lock the computer to an immovable object.
Page 25: Rear And Left Side Components
Rear and Left Side Components Rear and Left Side Components Component Infrared port Keyboard/mouse connector Parallel connector Docking connector External monitor connector Serial connector Power connector Tilt feet (2) Airflow exhaust Hard drive bay 2-6 Taking a Look at the Computer Rear and Left Side Components Function Provides for wireless IrDA...
Page 26: Bottom Components
Bottom Components Bottom Components Component Battery release latch Docking restraint latch recess MultiBay release latch Serial number Memory compartment Hard drive security plate Bottom Components Function Releases battery pack for removal from the bay. Helps secure the computer when docked in the optional ArmadaStation or Armada MiniStation.
Page 27: Interior Components
Interior Components Interior components vary by model, and some components are upgradable. To view information about your system components, double-click the Compaq Diagnostics icon in Control Panel. Preinstalled Software In addition to the Windows operating system, the computer has preinstalled software drivers, utilities, and programs. CAUTION: version will result in the loss of the Compaq value-add software and certain hardware functionality, such as PC Card support and...
Page 28: Using The Keyboard And Pointing Device
chapter SING THE OINTING This chapter describes the computer keyboard features, including the EasyPoint III pointing device and mouse buttons, hotkeys, embedded numeric keypad, and programmable keys. Using the Pointing Device and Mouse Buttons The EasyPoint III pointing device and mouse buttons are built into the keyboard for convenient, easy use.
Page 29: Changing Mouse Settings
Changing Mouse Settings You can change settings, such as click speed, pointer speed, and pointer shape. Click the Start button, point to Settings, click Control Panel, then double-click the Mouse icon to open Mouse Properties. To see the available settings, click the tabs at the top of the Mouse Properties dialog box.
Page 30: Hotkeys
Hotkeys Hotkeys are key combinations on the computer keyboard for performing functions quickly. To use a hotkey, press the simultaneously with another key. Function keys used in hotkey combinations have a blue icon representing the function. Hotkey Function Fn+F1 Popup window location. After pressing the hotkey, press the left, right, up, and down arrow keys to change the screen location where hotkey popup windows appear.
Page 31: Embedded Numeric Keypad
Embedded Numeric Keypad The embedded numeric keypad is a section of the main keyboard that converts to a numeric keypad when the num lock function is enabled. Press Fn+NumLk off. The num lock light turns on to indicate when num lock is on. When num lock is on, the blue numbers and symbols on top of the keys within the embedded numeric keypad are active.
Page 32: Assigning Programmable Keys
Assigning Programmable Keys To assign a program, document, or logo key to a programmable key: 1. Open the Programmable Keys dialog box as described earlier in this chapter. 2. Click the button next to the number of the programmable key that you want to assign in the current scheme.
Page 33: Adding Schemes
3. Click the Assign button. (A dialog box appears showing a list of programs.) If the Browse button shows instead of the Assign NOTE: button, click to remove the check mark from Show Advanced Options. 4. Highlight Unassigned in the list and click OK. (The word “Unassigned”...
Page 34: Using Power And Power Management
chapter SING OWER AND OWER ANAGEMENT This chapter describes power sources, power controls and indicators, turning on and shutting down the computer, and power management (including Suspend and Hibernation). Power Sources You can power the computer with a rechargeable battery pack. You can power the computer and charge the battery pack by connecting to an external power source.
Page 35: Power Controls And Light
Power Controls and Light The computer has two power controls and a power/suspend light: Power switch. Turns the computer on (and off, if Shut Down does not turn power off). Suspend button. Initiates and exits Suspend. Initiates Hibernation when pressed simultaneously with the Power/suspend light.
Page 36: Turning The Computer On And Off
Turning the Computer On and Off Turning the Computer On After you have connected the computer to an external power source or inserted a charged battery pack, turn on the computer by sliding the power switch power/suspend light turns on. Shutting Down the Computer Follow these steps to shut down the computer: 1.
Page 37: Power Management
Power Management Power management settings conserve power by shutting down components, initiating Suspend, or initiating Hibernation after a specified period of inactivity called a timeout. Initiating Suspend Suspend turns off power to system components when they are not being used. While operating on battery power, the system automatically initiates Suspend after a specified timeout, the factory-default is five minutes.
Page 38: Initiating Hibernation
Initiating Hibernation Hibernation saves all information in memory to a Hibernation file on the hard drive and shuts down the computer. When you turn on the computer again, your information returns to the screen at the point where Hibernation was initiated. Hibernation is not available when the computer is docked in NOTE: the optional ArmadaStation or Armada MiniStation.
Page 39: Power Management Settings
Power Management Settings You can access power management settings within Windows or by running Computer Setup. To run Computer Setup, turn on or restart the computer and press when the cursor appears near the upper-right corner of the screen. Select Computer SetupÆSystem FeaturesÆ Power Management.
Page 40 AC Energy Saver Tab In Windows NT, the AC Energy Saver tab allows you to turn on or off power conservation settings when connected to an electrical outlet. When AC Energy Saver is on, you can enable/disable Energy Save Monitor and set timeouts for the hard drive idle and screen save.
Page 41 Battery Conservation Settings Tab In addition to the battery conservation settings, this tab also has an option to turn off or on the low-battery warning beeps and, in Windows NT, an option to disable or enable CD-ROM auto insert notification. Conservation Level and Settings: View or change the level of battery conservation and the Custom conservation settings: High—provides maximum battery conservation and the most...
Page 42 Low Battery Warning Beeps: You can turn off or on the low- battery warning beeps. However, if you turn them off, the only indication of a low-battery condition may be the blinking battery light. CD-ROM Auto Insert Notification: In Windows NT, the Battery Conservation Settings tab includes an option to disable or enable CD-ROM Auto Insert Notification.
Page 43: Using Battery Packs
chapter SING ATTERY This chapter contains guidelines for using and storing battery packs, ensuring battery gauge accuracy, and extending battery pack operating time. For used battery recycling requirements, see “Battery Notice” in Appendix B. WARNING: pack, do not crush, puncture, or incinerate the battery pack or short the metal contacts.
Page 44: Battery Gauge Hotkey
Battery Gauge Hotkey The battery gauge hotkey, illustrated below, which shows the charge status of batteries in three possible positions: 1. Computer battery bay 2. Right MultiBay in the ArmadaStation or battery charging bay in the Armada MiniStation EX. 3. Left Multibay in the ArmadaStation (with the Armada 7000 Half-Height MultiBay Adapter) or in the Armada MiniStation EX.
Page 45: Battery Meter On Taskbar
Battery Meter on Taskbar The battery icon in the notification area (system tray) on the taskbar is a quick way to view the remaining battery charge. The icon changes appearance to indicate when the charge is getting low. Hold the onscreen pointer over the icon to see the charge in a tool tip.
Page 46: Charging Battery Packs
Charging Battery Packs You can charge the battery pack in the battery bay by connecting the computer to an external power source. When the battery pack begins charging, the battery light on the front of the computer turns on. When the battery pack completes its charge, the battery light turns off.
Page 47: Identifying And Resolving A Low-Battery Condition
Identifying and Resolving a Low-Battery Condition When a battery pack powering the computer reaches a low-battery condition, the battery light begins blinking and the system begins beeping three times about every minute. If you have disabled the low-battery warning beeps, the NOTE: blinking battery light may be the only indication of a low-battery condition.
Page 48: Replacing A Discharged Battery Pack
Replacing a Discharged Battery Pack Removing a Battery Pack To remove a discharged battery pack from the battery bay: 1. If the computer is on, save open files and initiate Suspend. The power/suspend light begins blinking. CAUTION: computer is on, save open files, initiate Suspend, then immediately replace the discharged battery pack.
Page 49: Extending Battery Pack Operating Time
Inserting a Battery Pack To insert a battery pack into the battery bay: 1. With the label on the battery pack facing up and the battery contacts facing in, insert the battery pack into the battery bay until it clicks into place. 2.
Page 50: Storing Battery Packs
Storing Battery Packs Store the battery pack in a cool, dry place. High temperatures reduce the life of the battery pack and cause it to lose its charge more quickly. The following are recommended storage temperatures: Less than one month, 32 F to 122 F (0 C to 50 C) No more than three months, 32 F to 104 F (0 C to 40 C) An unlimited time, 32 F to 86 F (0 C to 30 C) CAUTION:...
Page 51: Working With Removable Drives
chapter ORKING WITH EMOVABLE This chapter describes how to remove, insert, and care for removable drives and how to change the factory-default boot order. The computer has one hard drive bay that supports a removable hard drive and one MultiBay that supports a diskette drive, CD-ROM drive, or second hard drive.
Page 52: Caring For Removable Drives
Caring for Removable Drives Removable drives are fragile components that must be handled with care. A hard drive carrying case and a MultiBay device carrying case are supplied with the computer to protect drives when they out of the drive bays. CAUTION: removable drive, or loss of information, observe these precautions: Before removing or inserting a hard drive, shut down the...
Page 53: Placing Drives In Their Carrying Cases
Placing Drives in Their Carrying Cases A hard drive carrying case is supplied with the computer to protect a hard drive when it is out of the drive bay. Do not place a hard drive into a MultiBay device carrying case. Placing a Hard Drive into a Hard Dive Carrying Case A MultiBay device carrying case is supplied with the computer to protect a diskette drive or CD-ROM drive when it is out of the...
Page 54: Removing/Inserting A Hard Drive In The Hard Drive Bay
Removing/Inserting a Hard Drive in the Hard Drive Bay Removing a Hard Drive from the Hard Drive Bay The original hard drive in the computer hard drive bay has the software and drivers necessary for the computer to start (boot) and operate properly.
Page 55 4. Open the hard drive door by sliding the door latch down and pulling the door open Opening the Hard Drive Door 5. Grasp the hard drive tab and pull the drive from the drive bay. Removing the Hard Drive from the Hard Drive Bay 6.
Page 56: Inserting A Hard Drive Into The Hard Drive Bay
Inserting a Hard Drive into the Hard Drive Bay Before handling a removable drive, be sure you have IMPORTANT: read the cautions under “Caring for Removable Drives” earlier in this chapter. To insert a hard drive into the hard drive bay: 1.
Page 57 6. Close the computer if it is open and turn it upside down. 7. Use a Torx T-8 screwdriver to insert the original hard drive security plate, or use the screwdriver supplied with the computer to insert the tamper resistant security plate. CAUTION: To prevent damage to the hard drive or loss of data, always reinsert either the original hard drive security plate or the...
Page 58: Using Multibay Adapters
Before inserting a hard drive into the computer MultiBay, insert it into the Armada 7300 Hard Drive MultiBay Adapter. The adapter is included with an Armada 7300 hard drive option kit and is also available as a separate option. Before handling a removable drive, be sure you have IMPORTANT: read the cautions under “Caring for Removable Drives”...
Page 59: Removing/Inserting A Drive In The Armada 7000 Removable Drive Multibay Adapter
You may have either model. The adapter is not needed to insert an Armada 7300 removable drive into the Armada 7300 computer MultiBay. Before inserting...
Page 60 Removing a Drive from the MultiBay Adapter That Has One Release Latch To remove a drive from the Armada 7000 Removable Drive MultiBay Adapter that has one release latch on the right side: 1. Apply light pressure to both the top and bottom of the release latch on the right side of the adapter and pull it out slightly 2.
Page 61 Removing a Drive from the MultiBay Adapter That Has Two Release Latches To remove a drive from the Armada 7000 Removable Drive MultiBay Adapter that has two release latches on the bottom: 1. Slide the two release latches on the bottom of the adapter away from the center of the adapter until they click into the unlocked position 2.
Page 62 Inserting a Drive into the MultiBay Adapter That Has One Release Latch To insert a CD-ROM drive or diskette drive into the Armada 7000 Removable Drive MultiBay Adapter that has one release latch on the right side: 1. Hold the drive with the connector on the right facing the front of the adapter.
Page 63 Inserting a drive into the MultiBay Adapter That Has Two Release Latches To insert a CD-ROM drive or diskette drive into the Armada 7000 Removable Drive MultiBay Adapter that has two release latches on the bottom: 1. Slide the two release latches on the bottom of the adapter away from the center of the adapter until they click into the unlocked position 2.
Page 64: Removing/Inserting Drives In The Computer Multibay
Removing/Inserting Drives in the Computer MultiBay Removing a Drive from the Computer MultiBay Before handling a removable drive, be sure you have IMPORTANT: read the cautions under “Caring for Removable Drives” earlier in this chapter. To remove a drive from the MultiBay: 1.
Page 65: Inserting A Drive Into The Computer Multibay
Inserting a Drive into the Computer MultiBay Before handling a removable drive, be sure you have IMPORTANT: read the cautions under “Caring for Removable Drives” earlier in this chapter. For the steps to insert a hard drive into the hard drive NOTE: MultiBay adapter or to remove a diskette drive or CD-ROM drive from the removable drive MultiBay adapter, see “Using MultiBay...
Page 66: Inserting The Multibay Weight Saver
Inserting the MultiBay Weight Saver The MultiBay weight saver included with the computer covers the MultiBay opening without adding the weight of a drive. When a MultiBay device is not needed, insert the MultiBay weight saver to protect the MultiBay from dust and debris and to lessen the weight of the computer.
Page 67: Opening The Cd-Rom Tray
Opening the CD-ROM Tray The CD-ROM drive, included with the computer or purchased as an option, has a retractable tray for inserting and removing CDs. To open the CD-ROM tray, press the release button on the front of the drive when the computer is on.
Page 68: Changing The Drive Boot Order
Changing the Drive Boot Order When the computer is turned on, it searches for a drive to start (boot) from in a particular order. The default order is the first bootable CD-ROM, the first bootable diskette, then the first bootable hard drive. A bootable drive contains files needed by the computer to start and operate properly.
Page 69: Connecting External Desktop Equipment
chapter ONNECTING ESKTOP This chapter describes connecting the following widely used external options: PS/2-compatible keyboard, numeric keypad, mouse, or other pointing device Parallel device, such as a printer or SCSI adapter Serial device, such as a serial mouse or printer External monitor or overhead projector For information about connecting and using other NOTE:...
Page 70: Identifying External Connectors
Identifying External Connectors The illustration below identifies connectors for the equipment discussed in this chapter. Keyboard/mouse connector (PS/2-compatible) Parallel connector Docking connector External monitor/overhead projector connector Serial connector Identifying Connectors for External Desktop Equipment An arrow on a device connector or plug indicates the cable NOTE: should be connected with the arrow facing up.
Page 71: External Mouse Or Other Pointing Device, Keyboard, Or Numeric Keypad
External Mouse or Other Pointing Device, Keyboard, or Numeric Keypad You do not have to shut down the computer to connect an external PS/2-compatible mouse or other pointing device, keyboard, or numeric keypad. After connecting an external PS/2-compatible device, you can use either the external or the integrated device. Parallel and Serial Devices Window 95 automatically detects most new devices and installs device drivers.
Page 72: External Monitor/Overhead Projector
External Monitor/Overhead Projector The computer can support an external display with a resolution up to 1280 × 1024 in 256 colors. When an external monitor or overhead projector is connected, the factory-default is to simultaneously display on both screens. The hotkey switches between simultaneous display, the external Fn+F4 display, and the internal computer display.
Page 73 Image Panning or Expanding Image panning is automatically enabled when the Desktop Area setting is larger than the Resolution setting. The image pans to the larger desktop area when you move the onscreen pointer to the edges of the screen. Image centering/expanding is automatically enabled when the Desktop Area setting is smaller than the Resolution.
Page 74: Energy-Saving Monitor
Energy-Saving Monitor If the external monitor is an energy-saving monitor, you can enable the monitor energy-saving features either in Computer Setup or within Windows: In Windows 95, double-click the Display icon in Control Panel, then click Screen SaverÆEnergy Saving Features. In Windows NT, double-click the Power icon in Control Panel, then click AC Energy SaverÆEnergy Save Monitor.
Page 75: Using The Internal Modem
chapter SING THE If your computer has an integrated modem, this chapter tells you how to find online help and the preinstalled modem software program, how to connect the modem in different geographical regions, and how to connect the modem to a cellular phone in North America.
Page 76: Running The Communications Program
Running the Communications Program A communications program has been preinstalled on the computer for Windows 95 or for Windows NT. Online Help is available within the program. In Japan, if the computer does not have the preinstalled NOTE: communications program, contact your Compaq authorized dealer, reseller, or service provider for information about a communications program to use.
Page 77: Connecting The Modem In North America, Latin America, Japan, Or Hong Kong
Connecting the Modem in North America, Latin America, Japan, or Hong Kong If your computer has an RJ-11 modem jack on the right side of the computer, you will connect a standard telephone cable to that RJ-11 jack. (The 25-pin modem connector is for connecting the modem to a cellular phone in North America or to a wall jack in Europe or Australia.) If you purchased the computer in Europe or Australia, it...
Page 78: Connecting The Modem In Europe Or Australia
Connecting the Modem in Europe or Australia If you purchased the computer in Europe or Australia, a country- specific modem cable was included with the computer. You will use that 25-pin cable to connect the modem to a telephone wall jack in the country where you purchased the computer.
Page 79: Connecting The Modem To A Cellular Phone (Available Only In North America)
Connecting the Modem to a Cellular Phone (Available Only in North America) In North America, the modem can used with a cellular phone that is compatible with the modem. Refer to the online Modem Help for a list of compatible cellular phones and associated Compaq cellular phone cables.
Page 80 Registering the Cellular Phone with the Modem The modem does not look for a cellular phone connection until you enter a command to register the phone with the modem. Thereafter (unless the &J command is changed), the modem will look for the presence of the cellular phone and dial through it if it is connected.
Page 81: Using The Infrared Port
chapter SING THE The IrDA-compliant infrared port on the rear of the computer provides for cable-free communication with other IrDA-compliant computers and printers. The infrared port supports both high- speed connections up to 4 megabits per second (Mbps) and low- speed connections up to 115 kilobits per second (Kbps).
Page 82: Infrared Software
Infrared Software Infrared Monitor The Infrared Monitor utility configures and monitors serial infrared communication. To run Infrared Monitor, double-click the Infrared icon in Control Panel. For help using the utility, click the Help button. When you run Infrared Monitor, it searches for an infrared device within range;...
Page 83: Preparing For An Infrared Connection
Preparing for an Infrared Connection To establish a direct infrared connection between the computer and another IrDA-compliant device, follow these steps: If the connection is between two computers, ensure that each computer has a different computer name, according to Microsoft conventions. Ensure that the infrared ports on both devices are enabled and facing each other at a distance no greater than 1.5 feet (0.5 meter).
Page 85: Using Pc Cards
chapter PC C SING PC Cards (PCMCIA) are credit card–sized options that you can quickly insert to perform various tasks and remove when not needed. A few of the PC Card options available are fax/modems, network cards, hard drives, and memory. PC Cards are available in three types: Type I, Type II, and Type III.
Page 86: Compaq Pc Card Solutions List
Compaq PC Card Solutions List Compaq offers a list of PC Cards, including CardBus and Zoomed Video PC Cards, that are compatible with Compaq computers and meet rigorous Compaq quality standards. PC Cards in the first category, Premier, are comprehensively tested by Compaq.
Page 87: Inserting A Pc Card
Inserting a PC Card In Windows 95, you do not have to shut down or restart the computer to insert and use a PC Card. In Windows NT, you must restart the computer after inserting some cards, for example, LAN and SCSI. Refer to the online Help in CardWare and to the documentation included with the card to learn whether you must restart the computer after inserting your card.
Page 88: Removing A Pc Card
Removing a PC Card When the Computer Is Off In Windows NT, you must shut down the computer to NOTE: remove some cards, for example, LAN and SCSI. Refer to the online Help in CardWare and to the documentation included with the card to learn whether you must shut down the computer before removing the card.
Page 89 Removing a PC Card Using PC Cards 10-5...
Page 90: Using Audio Features
chapter SING UDIO This chapter describes the internal and external audio features of the computer. These features allow you to take advantage of the newest multimedia programs for business, presentations, education, and entertainment. The computer has an industry-standard 16-bit stereo sound system.
Page 91: Identifying The Audio Components
Identifying the Audio Components The following audio components are located on the front and right side of the computer: Microphone Volume control buttons Stereo speakers Stereo line-in jack Stereo speaker/headphone jack Microphone jack Audio Components 11-2 Using Audio Features...
Page 92: Using The Built-In Audio Components
Using the Built-In Audio Components Microphone The internal microphone on the front of the computer has a standard sensitivity of -50dB, which supports audio input whether the display is open or closed. The internal microphone is disabled if an external microphone is connected. Volume Control The volume control buttons adjust the volume of the internal speakers or, if connected, the external speakers, headphones, or...
Page 93: Connecting External Audio Equipment
Connecting External Audio Equipment Stereo Line-In Jack The stereo line-in jack is the input line for an external stereo player such as a CD player, stereo tuner, or tape deck. The input device must have a 3.5-mm stereo plug and must supply line input levels of 0.5 to 4.25 volts.
Page 94: Upgrading Ram Memory
chapter PGRADING This chapter describes the steps to install a memory expansion board to increase the amount of random access memory (RAM). See the online Options Catalog for a list of the available memory expansion boards. The computer has two memory slots. One slot contains the original system memory board.
Page 95: Installing A Memory Expansion Board
Installing a Memory Expansion Board If you have not replaced the original factory-installed screws in the memory compartment cover, you will need a Torx T-8 screwdriver to remove the screws. If you have replaced the original factory-installed screws in the memory compartment cover with the two security screws supplied with the computer, you must use the screwdriver supplied with the computer to remove and reinsert the screws.
Page 96 4. Turn the computer upside down. 5. Remove the two screws from the memory compartment cover The tamper-resistant screws supplied with the computer NOTE: have a post in the middle of the screw head. Only the screwdriver supplied with the computer removes those screws. A Torx T-8 screwdriver removes the factory-installed screws.
Page 97: Removing An Existing Memory Board
Removing an Existing Memory Board It is not necessary to remove an existing memory board unless both slots contain boards and you are upgrading one or both of them. If one slot is empty, skip this procedure and go to “Inserting a Memory Expansion Board.”...
Page 98: Inserting A Memory Expansion Board
Inserting a Memory Expansion Board The memory expansion board is keyed (notched) slightly off center to help you position it correctly. The notch is left of center, facing in, as you insert the board. To insert a memory expansion board: 1.
Page 99 3. Replace the memory compartment cover 4. Use the screwdriver supplied with the computer to insert the two tamper-resistant screws in the cover, or use your Torx T-8 screwdriver to reinsert the original screws Replacing the Memory Compartment Cover 12-6 Upgrading RAM Memory...
Page 100: Maintenance And Travel Guidelines
chapter AINTENANCE AND UIDELINES This chapter provides guidelines for routine care, steps to replace the pointing device cap, and preparations for traveling with or shipping the computer. Routine Care A few precautions and a little routine care will keep the computer in good condition and working properly: Avoid exposing the computer to direct sunlight or strong ultraviolet light for extended periods of time.
Page 101: Replacing The Pointing Device Cap
Do not place anything on top of the computer display. CAUTION: place anything on top of the computer when it is closed. Do not store any items on top of the computer when it is in the slipcase. Carry the computer in the slipcase, and avoid bumping the computer against hard objects.
Page 102: Air Travel
5. Close the display and all exterior doors on the computer. Do not close objects between the keyboard and display. 6. Disconnect the AC Adapter from the computer. When traveling, take the AC Adapter or an extra fully charged battery pack with you. 7.
Page 103: Shipping
Shipping Follow the same steps to prepare the computer for shipping that you follow for traveling. Pack the computer and external devices in their original packing boxes or similar boxes with sufficient packing material to protect them. If a drive must be mailed, do the following. Place the drive into its carrying case.
Page 104: Security Features Software Security
chapter ECURITY This chapter describes the following software and hardware security features: Software security Power-on password QuickLock/QuickBlank Setup password Device disabling Hardware security Hard drive in hard drive bay Memory compartment Optional cable lock EATURES Security Features 14-1...
Page 105: Software Security
Software Security Establishing a Power-On Password The power-on password prevents unauthorized use of the computer. After you establish a power-on password, you must enter it each time you turn on the computer. You can establish a power-on password within Windows or in Computer Setup. In Windows, double-click the Passwords icon in Control Panel, click the Computer Security tab, then click the Set button.
Page 106: Enabling Quicklock And Quickblank
Enabling QuickLock and QuickBlank If you enable QuickLock when you establish a power-on password, the keyboard and pointing device are disabled at power- on until you enter your power-on password. If you enable QuickBlank, the screen is blank at power-on until you enter your password.
Page 107: Changing Or Deleting A Password
Changing or Deleting a Password After establishing a power-on password or setup password, you can change or delete that password only in the password prompt window. To change the password, type the old password once and the new password twice, separated by the password delimiter for your keyboard, for example old password/newpassword/newpassword To delete your password, do not type a new password after...
Page 108: Hardware Security
Hardware Security A screwdriver, two tamper-resistant screws for the memory compartment cover, and a tamper-resistant hard drive security plate are supplied with the computer. The tamper-resistant Torx screw heads have an additional post in the middle, which the supplied screwdriver fits. You will need a Torx T-8 screwdriver to remove the factory- installed memory compartment screws and/or hard drive security plate.
Page 109: Memory Compartment Security Screws
Memory Compartment Security Screws Two tamper-resistant screws are supplied with the computer to provide security for the original system memory board and/or optional memory expansion board(s). To install the memory compartment security screws: 1. Shut down the computer and turn it upside down. 2.
Page 110: Cable Lock
Cable Lock A security cable slot is provided on the right side of the computer for an optional cable to lock the computer to an immovable object. A cable lock can be purchased from Kensington Microware Limited and major dealers worldwide. Ask for the Kensington MicroSaver Security System Model 64068.
Page 111: Intelligent Manageability
chapter NTELLIGENT Intelligent Manageability combines innovative hardware and software technology from Compaq and other leading vendors to make Compaq computers easier to inventory, troubleshoot, and protect. Intelligent Manageability provides Inventory Management, Fault Management, and Security Management. The lowercase i in the notification area (system tray) on the taskbar indicates that Intelligent Manageability is installed on the computer.
Page 112: Fault Management
Compaq Insight Manager refers to Intelligent Manageability NOTE: software on Compaq servers, which provides monitoring, remote maintenance, and asset management of network resources. The asset tag number can be changed in Computer Setup (see Chapter 16, “Computer Setup and Diagnostics Utilities”). Fault Management Fault Management provides the following features to help prevent the loss of critical data:...
Page 113: Computer Setup And Diagnostics Utilities Computer Setup
chapter OMPUTER IAGNOSTICS Compaq Utilities help you configure and test the computer and Compaq options. To run Compaq Utilities, follow these steps: 1. Turn on or restart the computer. To restart the computer, click the Start buttonÆShut DownÆRestart the ComputerÆYes. 2.
Page 114: Help Button
Computer Setup Run Computer Setup to set custom features that are not available within Windows. You may also need to run Computer Setup to configure some new devices. Help button For information about options on Computer Setup screens, click the Help button near the lower-right corner of the screen. View Menu The View menu in Computer Setup provides two ways to view settings: by type and by connection.
Page 115: Tools Menu
Tools Menu The Tools menu in Computer Setup includes the following options: Set Defaults—reestablishes the factory default settings. Resource Priorities—changes the priority of a resource type (IRQ, DMA, I/O address, and memory address). Resolve Conflicts—attempts to resolve configuration conflicts. Legacy—provides a way to add Legacy (ISA) devices that predate Plug and Play.
Page 116 6. Verify that Computer Checkup correctly detected the devices installed. Devices from other manufacturers may not be detected NOTE: or may be reported inaccurately. a. If the list is correct, select OK. The test option menu is displayed again. Go to step 7. b.
Page 117: View System Information (Inspect)
View System Information (INSPECT) The View System Information (INSPECT) utility provides information about the system configuration. You can display, print, or save the information. Within Windows, you can double-click Compaq NOTE: Diagnostics in Control Panel to view similar information. To run View System Information (INSPECT), follow these steps: 1.
Page 118: Prepare Computer For A Compaq Service Call (Remotepaq)
Prepare Computer for a Compaq Service Call (RemotePaq) This utility is only available in certain geographical regions and requires a modem. It allows your Compaq service provider to automatically run diagnostics on the computer. Follow your Compaq service provider’s instructions if you are requested to run RemotePaq.
Page 119: Troubleshooting
chapter ROUBLESHOOTING This chapter provides solutions to some common problems. If you have a problem with the computer, you may be able to easily resolve it with solutions provided in this chapter. In addition to a minor problems checklist, common problems and solutions are provided for the following topics: Audio Battery/battery gauge...
Page 120: Minor Problems Checklist
Minor Problems Checklist If you encounter a minor problem with your computer or software application, go through the following checklist for possible solutions. Is the computer connected to an external power source, or does it have a fully charged battery pack installed? Is the computer turned on (the power/suspend light is on)? Are all cables connected properly and securely? Was a nonbootable diskette in the computer diskette drive...
Page 121: Solving Audio Problems
Solving Audio Problems Problem Computer beeps once after you turn it on. Computer does not beep after the Power-On Self- Test (POST). Computer beeped three times and battery light is blinking. Computer beeped three times when exiting Suspend, and the battery light is blinking.
Page 122: Solving Battery And Battery Gauge Problems
Solving Battery and Battery Gauge Problems The solutions for “Solving Power Problems” also may be helpful. Problem Computer will not turn on when battery pack is inserted (and external power is disconnected). Computer beeped three times and battery light is blinking.
Page 123 Solving Battery and Battery Gauge Problems Problem Possible Cause After the battery light Hibernation has been began blinking, com- turned off, and the puter beeped twice computer has entered and the power/ a critical low-battery suspend light began condition. blinking. Battery light blinks to Low-battery warning indicate low-battery...
Page 124 Solving Battery and Battery Gauge Problems Problem Computer shut down and information in memory was lost when a battery pack was being replaced. Unsaved data was lost when system did not initiate Hibernation on critical low-battery condition. Battery charge does not last as long as expected.
Page 125: Solving Diskette And Diskette Drive Problems
Solving Battery and Battery Gauge Problems Problem Battery charge does not last as long as expected. (continued) Battery gauge is inaccurate Solving Diskette and Diskette Drive Problems Problem Cannot access diskette drive Diskette drive cannot write to a diskette. Continued Possible Cause Battery pack is being exposed to tempera-...
Page 126 Solving Diskette and Diskette Drive Problems Problem Diskette drive cannot write to a diskette. (continued) Diskette drive cannot read a diskette. Cannot boot from a diskette 17-8 Troubleshooting Possible Cause Diskette has a bad sector. Drive error has occurred. Diskette is not formatted.
Page 127: Solving Hard Drive Problems
Solving Hard Drive Problems CAUTION: of errors or failures. Problem Cannot access hard drive. Reading the hard drive takes an unusually long time after restarting the computer. Hard drive error occurs. Errors occur after booting from an additional hard drive. Maintain an up-to-date backup of your hard drive in case Possible Cause Hard drive is not...
Page 128: Solving Hardware Problems
Solving Hardware Problems Problem New device is not recognized as part of the computer system. Cannot access a removable drive. Computer beeps four times when turned on, power/suspend light is on, but screen remains blank. 17-10 Troubleshooting Possible Cause The system did not automatically configure the new device.
Page 129: Solving Infrared Problems
Solving Infrared Problems Problem Cannot link with another infrared- equipped computer. Cannot transmit data. Possible Cause The infrared software is not running on both computers. Interrupt request (IRQ) conflict. Baud rate conflict. # bits conflict. Stop byte conflict. Parity conflict. Target device is not IrDA-compliant.
Page 130: Solving Keyboard And Numeric Keypad Problems
Solving Infrared Problems Problem Cannot transmit data (continued) Solving Keyboard and Numeric Keypad Problems Problem Embedded numeric keypad does not work. External keyboard does not work. Keyboard and pointing device are locked. 17-12 Troubleshooting Continued Possible Cause A device was moved. Direct sunlight, fluorescent light, or flashing incandescent...
Page 131: Solving Memory Problems
Solving Memory Problems Problem Memory count during Power-On Self-Test (POST) is incorrect. “Out of Memory” message is displayed on the screen, or insufficient memory error occurs during operation. Possible Cause Optional memory expansion boards are installed incorrectly. System ran out of memory for the application.
Page 132: Solving Modem Problems
Solving Modem Problems Problem No dial tone. 17-14 Troubleshooting Possible Cause Phone service is not connected or is temporarily inter- rupted. The modem is not responding to commands from the keyboard. Speaker Control AT Command (ATM) is set to 0. Solution Connect a phone to the wall jack.
Page 133 Solving Modem Problems Problem Possible Cause Modem loses The cable connection connection. is loose. Call Waiting has not been disabled. Hang-up Delay S Register (S10) is set too low and noise on the line is causing the modem to disconnect. Characters are There is noise in the garbled or transfer...
Page 134: Solving Pc Card Problems
Solving PC Card Problems Also refer to the online Windows 95 Troubleshooting Help or the help available within CardWorks for Windows NT. Problem Computer does not beep when PC Card is inserted but PC Card works correctly. Computer does not beep when PC Card is inserted and PC Card does not...
Page 135 Solving PC Card Problems Problem Possible Cause Computer beeps Telephone cord is not twice but modem, plugged in all the way. fax, or network card does not work. You are trying to access the card using the wrong COM port. Network server is unavailable.
Page 136: Solving External Pointing Device Problems
Solving External Pointing Device Problems The following are common problems with an external mouse, trackball, or other pointing device. Problem External pointing device does not work Cursor skips or moves abnormally when using an external pointing device. Solving Power Problems Solutions for “Solving Battery Problems”...
Page 137 Solving Power Problems Problem Possible Cause Computer will not Battery pack may be turn on when defective. connected to external power if battery pack is in the computer. Computer turned off System initiated while it was left Hibernation after a unattended and preset timeout.
Page 138: Solving Printer Problems
Solving Printer Problems If you experience problems printing, refer to the printer documen- tation for instructions to run a printer self-test. If the self-test is successful, it is not a printer-specific problem. Problem Printer will not turn Printer will not print. Printer prints garbled information.
Page 139: Solving Screen Problems
Solving Screen Problems This section lists some common causes and solutions for computer display and external monitor problems You can perform a monitor self-test on an external VGA color or monochrome monitor by disconnecting the monitor from the computer. To do so, complete the following steps: 1.
Page 140 Solving Screen Problems Problem Screen is blank continued Screen is blank and the power/suspend light is blinking. Screen is blank, and the power/suspend light and battery light are both blinking. Computer screen is blank and the external monitor displays information. External monitor does not display information.
Page 141 Solving Screen Problems Problem Possible Cause Display on an The external monitor external monitor is is not Energy Star distorted. compliant, but monitor (continued) energy saving feature is enabled. Small red, green, or Small spots, called blue spots appear on-pixels, often on the computer appear on TFT TFT display.
Page 143: Compaq Customer Support
appendix OMPAQ Preparing for a Technical Support Call If you cannot solve a problem using the troubleshooting tips in Chapter 17 and the online Troubleshooting help, you may need to call technical support. To receive the fastest possible solution when you call, follow the instructions in Chapter 16 to run the Compaq diagnostics utilities and have the following available when you call: The computer...
Page 144: Worldwide Telephone Numbers
Worldwide Telephone Numbers Locate your geographical area in the following table and use one of the telephone numbers for Compaq assistance. General Information Numbers—Product information, technical assistance, and the location of your nearest Compaq authorized dealer, reseller, or service provider. Technical Support Numbers—Hardware technical support in analyzing system configuration and diagnostic problems or troubleshooting.
Page 145 Worldwide Telephone Numbers Location Belgium / Luxembourg Compaq Care Center General Fax Infoline (resellers, brochures) QuickLine (BBS) Order Software Backup Order Software Backup by Fax Brazil General Information Canada General Information Technical Support* Customer Support* Order Software Backup* Battery Pack Recycling* Caribbean General Information Technical Support...
Page 146 Worldwide Telephone Numbers Location Denmark General Information Technical Support Finland General Information Technical Support* QuickLine (BBS) France General Information Technical Support Germany Hotline Hotline Fax Infoline Infoline Fax QuickLine FaxPaq Order Software Backup* Hong Kong General Information Technical Support PaqFax Hungary General Information Technical Support...
Page 147 Worldwide Telephone Numbers Location Israel General Information Technical Support PaqFax Italy General Information Technical Support Japan General Information* Technical Support* Windows 95 Support* Order Software Backup * FaxStation Korea General Information Technical Support Malaysia General Information Technical Support Mexico General Information Technical Support PaqFax Netherlands...
Page 148 Worldwide Telephone Numbers Location New Zealand General Information Norway General Information Technical Support Poland General Information Technical Support Portugal General Information Technical Support Russia General Information Technical Support PaqFax Singapore General Information Customer Support Center PaqFax South Africa General Information Technical Support Spain General Information...
Page 149 Worldwide Telephone Numbers Location Switzerland General Information Technical Support QuickLine Bulletin Board Order Software Backup Taiwan General Information Technical Support Thailand General Information United Arab Emirates (Dubai) General Information United Kingdom General Information FaxPaq QuickLine Bulletin Board United States Product Information* Technical Support* PaqFax* Download Facility...
Page 150: Regulatory Notices
appendix EGULATORY Regulatory Agency Identification Numbers Regulatory agencies worldwide use agency series numbers for product identification. Each approved product displays the assigned agency series number. To ensure continued safe and reliable operation, the options listed below should be used only with Compaq series 2910, 2910A, and 2910B computers.
Page 151: Federal Communications Commission Notice
Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Page 152: Canadian Notice
To identify this product, refer to the Series number found on the product. For questions regarding this declaration, write Compaq Computer Corporation P. O. Box 692000, Mail Stop 510101 Houston TX 77269-2000 or call (281) 514-3333. Canadian Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Page 153: German Ergonomics Notice
German Ergonomics Notice The Compaq 2910 series of computers have been evaluated and found to comply with the requirements of ZH 1/618, 1980. The computers were evaluated using MS-DOS Version 3.31 or higher, BASICA/T, and the EGA_THIN.CPI character set, as published by Compaq.
Page 154: Power Cords
In North America, dispose of nickel metal hydride or lithium ion batteries by taking advantage of the Compaq battery recycling program. You will be provided with a postage-paid battery pack mailer preaddressed to a reclamation facility where the metals are recycled. Call the telephone number listed for your location in Appendix A for more information.
Page 155: Laser Safety
Laser Safety All Compaq systems equipped with laser products comply with appropriate safety standards, including IEC 825. With specific regard to the laser, the equipment complies with laser product performance standards set by government agencies for Class 1 laser products. It does not emit hazardous light; the beam is totally enclosed during all modes of customer operation and maintenance.
Page 156 Safety Precautions for Modems Always follow these basic safety precautions when using a modem or telephone that is not cordless. WARNING: fire: Never connect or use a modem or telephone during a lightning storm. There may be a remote risk of electric shock from lightning.
Page 157: Telephone Consumer Protection Act Of 1991
Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the proper functioning of your equipment. If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service. If you experience trouble with this telephone equipment, contact your local telephone company for information on obtaining service or repairs.
Page 158 Before installing the equipment, users should ensure that it is permissible to be connected to the facilities of the local tele- communications company. The equipment must also be installed using an acceptable method of connection. In some cases, the company’s inside wiring associated with a single line individual service may be extended by means of a certified connector assembly (telephone extension cord).
Page 159 AUSTEL Requirements CAUTION: software used with the modem, to the values contained in the Telephone Answering Machine documentation will result in the modem being operated in a non-compliant manner. Consequently, there would be no permit in force for this equipment, and the Telecommunications Act 1991 prescribes a penalty of $12,000 for the connection of non-permitted equipment.
Page 160 U.K. BABT User Information Safety The Compaq series 577 global modem is intended for use in the Compaq 2910 series of computers. For the purposes of BABT approval, the Compaq series 577 global modem is classified as a host-independent product. The following information characterizes the requirements of the host system in order to maintain the reliable use of the Compaq series 577 global modem:...
Page 161 Telephone Network Connection The modem is suitable for connection to the Public Switched Telephone Network (PSTN) direct exchange lines and relevant branch systems (PBXs). A ringer equivalent number (REN) is a value given to all apparatus to be connected to the PSTN. Its value can be taken and used to calculate the maximum number of equipment items that can be connected in parallel without impairing the performance of the standard bell circuit.
Page 162 Automatic dialing Tone detection of busy tone, dial tone, or number unobtainable tone Auto clear from the call origination end Loop disconnect (pulse) dialing Multifrequency (tone) dialing Any other usage will invalidate the approval of the apparatus if, as a result, it ceases to conform to the standards against which approval was granted.
Page 163 If the above mentioned difficulties are experienced, please contact your product supplier or your authorized Compaq reseller in the United Kingdom. This device is intended for auto-answering of incoming calls. Under normal conditions callers will be accustomed to calls being answered within 10 seconds, and a majority of callers will abandon calls that are not answered within 45 seconds.
Page 164: Electrostatic Discharge
appendix LECTROSTATIC A discharge of static electricity from fingers or other electrostatic conductors may damage electronic components. Before handling electrostatic-sensitive components, discharge static electricity by one of the methods described in this appendix. Preventing Electrostatic Discharge When Handling Removable Drives To prevent electrostatic damage to removable drives, observe these precautions: Before handling a removable drive, discharge static electricity...
Page 165: Grounding Methods
Before touching an electronic component, discharge static electricity by one of the grounding methods described later in this appendix. If you must leave the area during installation, remember to reground yourself before resuming installation. Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.
Page 166: Specifications
appendix PECIFICATIONS The following guidelines provide a safe operating environment for your computer. Temperature Operating Nonoperating (excluding battery pack) Relative Humidity (non-condensing) Operating Nonoperating Maximum Altitude (unpressurized) Operating Nonoperating Operating Environment U.S. 50 to 104°F -4 to 140°F 10 to 90% 5 to 90% 38.7°C Maximum Wet Bulb 0-10,000 ft...
Page 167 AC Adapter Power Requirements Rated Voltage Rated Current Rated Frequency Range NOTE: This product is designed for IT power systems in Norway with phase-to-phase voltage not exceeding 240Vrms. Height Width Depth D-2 Specifications 100–240 Volts AC 1.0 Amp 50 to 60 Hz Computer Dimensions U.S.
Page 168: Index
See software Armada MiniStation, 2-2, 2-7, 4-1, 4-5, 5-4, 6-9, 6-18, 7-6 Armada 7000 Removable Drive MultiBay Adapter, 6-3, 6-9–6-13 Armada 7300 Hard Drive MultiBay Adapter, 6-8 ArmadaStation, 2-2, 2-7, 4-1, 4-5, 5-4, 6-9, 6-18, 7-6, 11-3 asset management, 15-1...
Page 169 cable slot, security, 2-5, 14-7 cable, modem, 1-2, 2-4, 8-3, 8-4, 13-3 cache memory, 2-1 caps lock light, 2-3 caps, spare pointing device, 1-2, 3-1, 13-2 card and socket services, 10-2 CardBus. See PC Cards CardWare for Windows NT, 10-2, 10-3 carrying case computer, 1-2, 13-2, 13-3 hard drive, 1-2, 6-2, 6-3...
Page 170 Control Panel Add New Hardware icon, Windows 95, 7-3 Compaq Diagnostics icon, 2-8, 12-1, 16-5 customizing settings, 1-10 Display icon, 7-4 Keyboard icon, 3-4 Mouse icon, 3-2 Multimedia icon, 11-3 Passwords icon, 14-2 Power icon, 4-6 Programmable Keys icon, 3-4 conventions used in guide, xi cord, power, 1-2, 1-4, 13-3, B-5 Create Diagnostics Diskette utility,...
Page 171 fan, 2-6, 4-2 fault management, 15-2 features overview, 2-1 file transfer, wireless, 2-1, 9-2 floppy disk drive. See diskette drive Fn key, 3-2, 3-3 graphics controller, 2-1, 7-5, 16-2 grounding methods, C-2 hard drive, 2-4 backing up, 6-4, 13-2, 17-9 caring for, 6-2 carrying case, 1-2, 6-2, 6-3 door, 6-5, 6-6...
Page 172 jack microphone, external, 2-4, 11-2, 11-4 RJ-11 modem, 2-5, 8-3 stereo line-in, 2-4, 11-2, 11-4 stereo speaker/headphone, 2-4, 11-2, 11-4 Just Connect, 8-2 Kensington lock, 14-7 keyboard components, identifying, 3-2 external connector, 2-6, 7-2, 7-3 hotkeys, 3-3 icon in Control Panel, 3-4 troubleshooting, 17-12 keypad embedded numeric, 3-2, 3-4...
Page 173 MultiBay, 2-4, 6-1, 6-14–6-16 device carrying case, 1-2, 6-2, 6-3, drive light, 2-3 inserting drive, 6-15 release latch, 2-7, 6-14, 6-16 removing drive, 6-14 weight saver, 1-2, 6-16 MultiBoot, 6-18, 16-2 Multimedia icon in Control Panel, 11-3 mute, 11-3, 17-3 notices, regulatory, B-1 num lock, 3-4 num lock light, 2-3...
Page 174 Power Properties, 4-6 power/suspend light, 1-7, 2-3, 4-2, 4-3, 4-4, 5-5, 5-6 power-on password, 14-2, A-1 Power-On Self-Test, 17-3, 17-13 printed documentation, 1-2 printer, 7-1, 7-2, 7-3, 17-20 problem solving. See troubleshooting processor, 2-1 product identification number (PIN), programmable keys, 2-3, 3-2, 3-4–3-6 assigning, 3-5 icon in Control Panel, 3-4 icon on taskbar, 3-4...
Page 175 software drivers. See device drivers solving problems. See troubleshooting Sound Recorder, 11-1 spare caps, pointing device, 1-2, 3-1, 13-2 speakers external, 2-4, 11-2, 11-4 internal, 2-3, 11-2, 11-3 specifications, computer, D-1 static electricity. See electrostatic discharge stereo headphones, external, 2-4, 11-2, 11-4 headset, external, 2-4, 11-2, 11-4 line-in jack, 2-4, 11-2, 11-4 speakers, external, 2-4, 11-2, 11-4...
Page 176 unpacking computer, 1-2 utility Computer Checkup (TEST), 16-1, 16-3 Computer Setup, 16-1, 16-2 Create Diagnostics Diskette, 16-1, 16-6 Manage Diagnostics Partition, 16-1, 16-6 RemotePaq, 16-1, 16-6 View System Information (INSPECT), 16-1, 16-5 ventilation, 2-6, 4-2 View System Information (INSPECT), 16-1, 16-5 volume control buttons, 2-3, 11-2, 11-3, 17-3 wave table synthesis, 2-2...

This manual is also suitable for:

Armada 7300 series

HP Armada 7300 Reference Manual

Chapter 1 GETTING STARTED

Chapter 2 TAKING a LOOK at the COMPUTER

Chapter 3 USING the KEYBOARD and POINTING DEVICE

Chapter 4 USING POWER and POWER MANAGEMENT

Chapter 5 USING BATTERY PACKS

Chapter 6 WORKING with REMOVABLE DRIVES

Chapter 7 CONNECTING EXTERNAL DESKTOP EQUIPMENT

Chapter 8 USING the INTERNAL MODEM

Chapter 9 USING the INFRARED PORT

Chapter 10 USING PC CARDS

Chapter 11 USING AUDIO FEATURES

Chapter 12 UPGRADING RAM MEMORY

Chapter 13 MAINTENANCE and TRAVEL GUIDELINES

Chapter 14 SECURITY FEATURES Software Security

Chapter 15 INTELLIGENT MANAGEABILITY

Chapter 16 COMPUTER SETUP and DIAGNOSTICS UTILITIES Computer Setup

Chapter 17 TROUBLESHOOTING

Appendix A COMPAQ CUSTOMER SUPPORT

Appendix B

Regulatory Notices

Appendix C ELECTROSTATIC DISCHARGE

Appendix D

Specifications

Quick Links

Related Manuals for HP Armada 7300

Summary of Contents for HP Armada 7300

This manual is also suitable for:

Table of Contents