18 volt cordless drill/driver with 1/2" chuck (16 pages)
Summary of Contents for Chicago Electric 45338
Page 1
Tools required for assembly and service may not be included. For technical questions or replacement parts, please call 1-800-444-3353. 45338 . All rights reserved. No portion of this manual or any artwork ®...
SKU 45338 For technical questions, please call 1-800-444-3353. NOtICE is used to address practices not related to personal injury. CAutION, without...
Page 3
Always wear eye protection. SKU 45338 For technical questions, please call 1-800-444-3353. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropri- ate conditions will reduce personal injuries.
Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. SKU 45338 For technical questions, please call 1-800-444-3353. use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed.
• Arsenic and chromium from chemi- cally treated lumber Your risk from these exposures var- SKU 45338 For technical questions, please call 1-800-444-3353. ies, depending on how often you do this type of work. To reduce your...
To reduce vibration, maintain the tool as explained in this manual. If any abnormal vibration occurs, stop use immediately. SAVE tHESE INStRuCtIONS. SKU 45338 For technical questions, please call 1-800-444-3353. gROuNDINg tO PREVENt ELECtRIC SHOCK AND DEAtH FROM INCORRECt gROuNDINg...
Inc., the Canadian Standard Association, and the National Electri- cal Code. (See Outlets for 2-Prong Plug.) SKU 45338 For technical questions, please call 1-800-444-3353. Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration. (See Outlets for 2-Prong Plug.)
Page 8
150% of the rated amperes. Symbology Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. Volts Alternating Current Amperes No Load Revolutions per Minute n 0 xxxx/min. (RPM) SKU 45338 For technical questions, please call 1-800-444-3353. Page 8...
Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. SKU 45338 For technical questions, please call 1-800-444-3353. Assembly Housing (29) Auxiliary Handle (501)
Insert the Chuck Key (3) into the Chuck (2) and turn counterclockwise to open the mouth of the Chuck. Insert the hammer bit or the drill bit (not supplied) all the way into the Chuck. Turn the Chuck Key clockwise to tighten the Chuck on the bit.
Page 11
Gear Setting Control Figure F (top view) On the top of the Hammer Drill, push the Gear Setting Control to select plain drilling or hammer drilling. A symbol for a drill bit indicates plain drilling is selected. If a hammer is shown, it is set for hammer drilling.
Periodically blow out the motor air vents of dust and debris using com- pressed air. SKU 45338 For technical questions, please call 1-800-444-3353. Over time, if the performance of the tool diminishes, or it stops working completely, it may be necessary to replace the motor’s Carbon Brush...
LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 45338 For technical questions, please call 1-800-444-3353. PARtS LISt Qty.
Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not avail- able individually as replacement parts. SKU 45338 For technical questions, please call 1-800-444-3353. Page 14...
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353 SKU 45338 For technical questions, please call 1-800-444-3353. Page 15...