Chicago Electric 66910 Set Up And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Chicago Electric Manuals
  4. Chippers/Shredders
  5. 66910
  6. Set up and operating instructions manual

Chicago Electric 66910 Set Up And Operating Instructions Manual

Chicago electric chipper user manual 2.5 hp
Hide thumbs

Advertisement

Table of Contents

CHIPPER SHREDDER
SEt uP anD OPERatIng InStRuCtIOnS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SaVE tHIS Manual.
©
Copyright
2009 by Harbor Freight Tools
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 10h
2.5 HP
Model
66910
®
. All rights reserved. No portion of this manual or any artwork

Advertisement

Table of Contents
loading

Related Manuals for Chicago Electric 66910

Summary of Contents for Chicago Electric 66910

  • Page 1 Tools required for assembly and service may not be included. For technical questions or replacement parts, please call 1-800-444-3353. Revised Manual 10h 2.5 HP Model 66910 ® . All rights reserved. No portion of this manual or any artwork...

  • Page 2: Important Safety Instructions

    – MInIMuM WIRE gaugE FOR EXtEnSIOn CORDS EXtEnSIOn CORD ampere lEngtH Rating 25’ 50’ (at full load) 0 – 6 6 – 10 10 – 12 12 – 16 (120 VOlt) 100’ 150’ Not recommended SKU 66910...
  • Page 3 Do not abuse the Cord - Do not carry appliance by cord or pull on it to disconnect from receptacle. Keep the cord from heat, oil, and sharp edges. SKU 66910 For technical questions, please call 1-800-444-3353. Use only three-wire outdoor extension cords that have three-prong grounding plugs and grounding receptacles that accept the appliance’s plug.

  • Page 4: Personal Safety

    Inspect extension cords periodically and replace if damaged. Keep handles dry, clean, and free from oil and grease. Check for damaged parts - Before using the equipment, checked to determine that all guards will operate properly and perform their intended function. Check SKU 66910...

  • Page 5: General Safety

    Disconnect the Power Cord, and take the following steps: Remove any foreign or clogged material. SKU 66910 For technical questions, please call 1-800-444-3353. Check for any loose parts and tighten. Replace or repair damaged parts. Periodically stop the Chipper Shredder...

  • Page 6: Specifications

    14mm-17mm Wrench unPaCKIng When unpacking, make sure the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at 1-800-444-3353 as soon as possible. Page 6 For technical questions, please call 1-800-444-3353. SKU 66910...
  • Page 7 Right legs in diagram. Secure front Axle in place using Curved Washers (27) and Bolts (28). 31 30 29 REV 10h SKU 66910 For technical questions, please call 1-800-444-3353. aSSEMBly FROM aCCIDEntal OPERatIOn: turn the Power Switch off and...
  • Page 8 Leg assembly. Secure with one Curved Washer (27) and Lock Nut (75) each. With assistance, turn the assembly back over. Tighten all Bolts (28, 32, 64) and Lock Nuts (75), including the ones left loose from Phase 1. REV 10h SKU 66910...
  • Page 9 Washers (8), Spring Washers (6) and Safety Screws (7). REV 10h SKU 66910 For technical questions, please call 1-800-444-3353. Attach the Brace (77) to one of the Legs and insert the Feed Stick (78) into it.

  • Page 10: Product Features

    IMPORTANT: Branches cannot be more than 1-1/4” in diameter. Never attempt to cut limbs over 1-1/4” in diameter. Doing so can cause equipment damage and/or serious personal injury. WaRnIng! tO PREVEnt ElECtRIC SHOCK anD SERIOuS PERSOnal InJuRy: the extension cord SKU 66910...
  • Page 11 “OFF” position. Remove the Safety Lock-Off Switch from the Power Switch. Then unplug the Power Cord (37) from REV 10h SKU 66910 For technical questions, please call 1-800-444-3353. its extension cord. (See Figures D and E.) Wait until all moving parts of the Chipper Shredder have stopped moving.
  • Page 12 Blades to the Disc (21). Turn the Blades over to expose the sharp edges. Then retighten the Screws to secure the Blades to the Disc. Call 1-800-444-3353 for replacement blades. BlaDE (20) SCREWS (19) REV 10h SKU 66910...

  • Page 13: Troubleshooting

    PREVEnt SERIOuS InJuRy FROM aCCIDEntal OPERatIOn OR ElECtRIC SHOCK: turn the Power Switch (42) of the Chipper Shredder to its “OFF” position and unplug the unit from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. Problem Chipper Shredder will not start.

  • Page 14: Parts List

    Washer Screw Screw Spring Screw Steel Pad Small Rivet Chute Lock Nut Washer Safety Screw Screw Cupped Washer Lock Nut Feed Stick Brace Screw 5mm Allen Wrench 6mm Allen Wrench 14mm-17mm Wrench Spring Washer Description Qty. REV 10g SKU 66910...

  • Page 15: Assembly Diagram

    DIagRaM REV 10g SKU 66910 For technical questions, please call 1-800-444-3353. Page 15...

  • Page 16: Limited 90-Day Warranty

    Record Product’s Serial number Here: note: If product has no serial number, record month and year of purchase instead. note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. DISTRIBUTOR SKU 66910...

Table of Contents