Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Teledyne Lecroy PP009-1
Summary of Contents for Teledyne Lecroy PP009-1
- Page 1 PP009-1 PP009-2 Operator’s Manual PP009 Passive Probe...
-
Page 2: Warranty
The customer will be responsible for the transportation and insurance charges for the return of products to the service facility. Teledyne LeCroy will return all products under warranty with transportation charges prepaid. -
Page 3: Safety Instructions
Operator’s Manual Safety Instructions Follow generally accepted safety procedures in addition to the precautions specified in this section. The overall safety of any system incorporating this accessory is the responsibility of the assembler of the system. Symbols These terms and symbols may appear on the probe body or in this manual to alert you to important safety considerations. - Page 4 PP009 Passive Probe Do not overload. To avoid electric shock or fire, do not apply any potential to the probe leads that exceeds the maximum rating of the probe. Comply with voltage derating curve. When measuring higher frequency signals, comply with the Voltage vs. Frequency Derating Curve. Observe all terminal ratings.
-
Page 5: Specifications
Introduction The PP009 is a miniature high impedance passive probe designed for use with ≤ 600 MHz Teledyne LeCroy oscilloscopes. Its high input resistance and low capacitance make it ideal for general purpose probing of signals with frequency content from DC through several hundred MHz. -
Page 6: Operating Environment
PP009 Passive Probe Operating Environment Temperature, Operating to 50 Temperature, Storage to 71 Altitude, Operating Up to 2000 m (6560 ft) Humidity, Operating 5% to 85% RH to 30° C 5% to 65% RH 30° C to 40° C 5% to 45% RH above 40° C General Characteristics Cable Length 1.3 m (4.3 ft) -
Page 7: Connectivity Accessories
The PK005A series of connectivity accessories is compatible with any Teledyne LeCroy 5 mm PP009 series probe. Accessories are shown with the Teledyne LeCroy part number followed by the description. -
Page 8: Standard Accessories
PP009 Passive Probe Standard Accessories PK1-5MM-101 PK1-5MM-102 PK1-5MM-103 Sprung Hook Standard Ground Lead Adjustment Tool PK1-5MM-104 PK1-5MM-105 PK1-5MM-106 Rigid Tip, 0.8 mm Insulating Cap Color Coding Rings (set) Protective Cap Optional Accessories ROUND EADS PK1-5MM-119 PK1-5MM-120 PK1-5MM-121 Ground Lead with mini clip Ground Lead, 8 mm socket Ground Lead, 2 mm plug PK1-5MM-122... - Page 9 Operator’s Manual IPS AND PRINGS PK1-5MM-109 PK1-5MM-124 PK1-5MM-108 PK1-5MM-118 Spring Tip, 0.8 mm Spring Tip, 0.38 mm IC Cap, 2.54 mm pitch Ground Spring NPUT DAPTERS AND LIPS PK1-5MM-111 PK1-5MM-112 PK1-5MM-116 PK1-5MM-117 Single Lead Adapter Dual Lead Adapter Adapter, 2 mm plug Adapter, 4 mm plug PK1-5MM-113 PK1-5MM-114Y...
-
Page 10: Use And Maintenance
Use of PCB Adapter The PCB adapter (Teledyne Lecroy P/N PK1-5MM-107) is intended to be designed into and permanently installed in circuit boards to provide a reliable, high frequency test point which eliminates the need to hand hold the probe. -
Page 11: Probe Compensation
Operator’s Manual Probe Compensation Proper compensation of the probe is required to assure good amplitude accuracy in the dynamic portions of the waveform being measured. LF compensation matches the probe to differences in oscilloscope input capacitance. The LF compensation should always be checked and adjusted as needed when first connecting a passive probe to the oscilloscope input. - Page 12 PP009 Passive Probe Tip Selection and Replacement The PP009 probe is supplied a rigid tip. The spring-loaded tips PK1-5MM-109 (0.8 mm) and PK1-5MM-124 (0.38 mm), which can be ordered from Teledyne LeCroy as optional accessories, have sharp points and an on-axis requirement.
-
Page 13: Environmental Compliance
Operator’s Manual Certifications Teledyne LeCroy certifies compliance to the following standards as of the date of publication. See the EC Declaration of Conformity shipped with the product for current certifications. EC Declaration of Conformity - Safety The probe meets intent of EC Directive 2014/35/EU for Product Safety. - Page 14 PP009 Passive Probe...
- Page 16 928598-00 Rev A July, 2017...
- Page 17 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Teledyne LeCroy PP009-1 PK1-5MM-118 PK1-5MM-102 PK1-5MM-119 PK1-5MM-105 PK1-5MM-101 PK1-5MM-104...