21.Configuration wizard 1.1 Setup Wizard Page Connect to WiFi and log in to app , automatically jump to the configuration wizard page (NO password in default) Note:The device needs to be restored to factory Figure 1-1 ...
1.3 Enter the password to relay WiFi Figure 1-3 Click Confirm, repeater needs to be connected to the root router to verify the password Figure 1-4 Figure 1-5...
1.4 WiFi Settings Configure your extended WiFi network. Note :The sync WiFi switch is turned on by default, and you can customize WiFi Settings after you turn it off Figure 1-6 1.5 Device Admin Password Note:Synchronize administrator password switch is turned on by default. You can customize administrator password after turning it off...
Page 7
Figure 1-7 1.6 Summary Check the information, and then click “Finish” to save the configuration.
Figure 1-8 2.Login 2.1 Login APP After completing the configuration wizard, please reconnect to the WiFi and log in to app again. Admin Password:The Device administrator Password you set in Wizard Page.
Figure 2-1 3 .Home Page Home page information is displayed below, including signal strength, internet connection status, device information and logout button.
Figure 3-1 3.1 device Information Display Page Home>>Info It shows basic information of router,including device name,FW version and Hardware version of router. Figure 3-2...
3.2 Logout Button Home>>Logout Click “Logout” to exit the current login and jump to the login page. 4 .Device Page 4.1 Connected Clients List It shows all Connected Clients information,including device name,mac address,ip address and connection method. Figure 4-1...
4.2 Device details Page Device>>Device details page The device details page shows details information of connected device. You can set the remark of connected device. Click the “add to blacklist” button to add the device to blacklist. Figure 4-2 4.3 Blacklist Page Device>>Blacklist The blacklist page shows all the devices added to blacklist.
Click “Remove blacklist” to remove the device from blacklist. Figure 4-3 5 .Basic Configuration 5.1 Administrator Password Settings Basic Configuration>>Administrator Password To set the administrator password, you need to enter the original password for verification,then enter a new administrator password and verify it again. Figure 5-1 Figure 5-2 After modifying the administrator password,app will automatically jump to the login page.
5.2 Root Router Connection Basic Configuration>>Root Router Connection You can view the current root router on this page, or click Scan to select the network to be relayed. Figure 5-3 5.3 WIFI Settings Basic Configuration>>WIFI Settings Use this section to configure the wireless settings for your repeater.
Figure 5-4 5.3.1 Advanced Setup Configure the 2.4G or 5G WIFI SSID ,password and security. Figure 5-5 5.3.2 Smart Connect When Smart Connect feature is on, your wireless device can only find one wireless SSID of the router, and it will automatically match the 2.4G or 5G band WIFI according to the connection signal strength.
Page 16
Figure 5-6 After the smart connection is closed, the 2.4G WIFI and the 5G WIFI can be searched on the terminal wireless device respectively, and there are two wireless bands to be displayed on the page. Figure 5-7...
6 .Advanced Configuration 6.1 WiFi Advanced Settings Advanced Configuration>>WiFi Advanced Settings You can configure 2.4G and 5G wifi advanced configuration by this section, such as SSID Broadcast and security mode. Figure 6-1 Figure 6-2 6.2 Online Upgrade Advanced Configuration>>Online Upgrade This page will display your current firmware version.
7. System Settings 7.1 FAQ FAQ list shows the Frequently Asked Questions. Figure 7-1 Figure 7-2 7.2 About Us This section shows the app version,website and technology support. Figure 7-3...
7.3 Cache clear Click “Clear cache” to clear the cache of app. Figure 7-4...
Page 20
Frequently Asked Questions: Why the connected node can not be managed: Please confirm that the mobile wifi is connected to the SSID of the device to be managed How to restore the router to factory settings: When the power is on, sting the repeater's "Reset" pinhole for 10 seconds to restore the factory settings.
Page 21
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ‐ Reorient or relocate the receiving antenna. ‐ Increase the separation between the equipment and receiver. ‐Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ‐Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The device is restricted to indoor use only when operating in the 5150 to 5250 MHz frequency range. ...