GE JSP39DN Dimensions And Installation Information

JSP39DN
GE 30" Slide-In Electric Range with Self-Cleaning Oven
®
Dimensions and Installation Information (in inches)
Note: Cabinets installed adjacent to slide-in ranges must have an adhesion spec
KW Rating
of at least 194° temperature rating.
240V 11.6
Note: To reduce the possibility of scorching the side walls above the countertop
when no load is present on burners, it is recommended that a minimum 6"
208V
8.7
spacing from adjacent side wall be allowed for possible extended high-heat
element operation.
Receptacle Locations: For all 30" Slide-In Ranges locally approved flexible service cord or conduit
must be used because terminals are not accessible after range installation. See shaded area
in drawing for location of electrical outlet box. Recommended outlet locations allow range to be
installed directly against rear wall.
Optional Kits For Slide-In Body Sides
Electric Ranges
(Slide-in ranges are sold
(Available At Additional Cost) without sides installed. Can
be installed on either left
Accessory Backguards
or right when unit has one
(Attaches to the back of range
exposed side [no cabinet
as a backguard when unit is
adjacent]. Kit contains
installed in 30" free-standing
1 body side)
cutout)
JXS77WW (White)
JXS32WW (White) - 4" High
JXS77BB (Black)
JXS32BB (Black) - 4" High
Rear Filler Strip
JXS37WW (White) - 5-1/4" High
JXS37CC (Bisque) - 5-1/4" High WB07T10680 - Black Filler Strip Assembly
JXS37BB (Black) - 5-1/4" High WB07T10681 - White Filler Strip Assembly
WB07T10682 - Bisque Filler Strip Assembly
For answers to your Monogram, GE Profile
®
GE appliance questions, visit our website at
®
ge.com or call GE Answer Center
®
800.626.2000.
Optional Lower Trim Kits
(If counter height is greater
than 36.5", a lower trim kit
is recommended to extend
the useful height to 38"
maximum)
JXS56WW – White
JXS56BB – Black
or
™
service,
If you are NOT using the
optional Filler or Backguard:
23-3/16
30
Recommended
6" Min.
From Walls
35-7/8"–38"
from floor to
countertop
2-7/8"
To Front
Surface Of
Countertop
If you are using the optional
If you are NOT using the
Filler or Backguard:
optional Filler or Backguard:
23-3/16
30
If you are using the optional
Filler or Backguard:
If the countertop area is not flat, excess tension may be applied to the glass cooktop causing breakage
and voiding the warranty. Make sure the wall covering, countertop, flooring and cabinets around the range
can withstand the heat (up to 200°F) generated by the range.
A. Allow 30" minimum clearance between surface units and bottom of unprotected wood or metal cabinet,
25
B. This appliance has been approved for 0" spacing to adjacent surfaces above the cooktop. However,
To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage space above
30
the cooktop should be avoided. If cabinet storage space is to be provided above the cooktop, the risk can
be reduced by installing a range hood that projects at least 5" beyond the front of the cabinets. Cabinets
installed above the cooktop must be no deeper than 13".
Shave Raised Edge To Clear
31-1/8" Wide Control Panel
30" Min .
Excluding Models JSS28 and JSP39
30 " Mi n.
Recommended
6" Min.
9/16
From Walls
30" Min .
30 " Mi n.
Acceptable
23-3/16
Electrical 13" Max.
Acceptable
Outlet Area 23-3/16
Electrical
15" Min.
Outlet Area
25
35-7/8"–38"
2-1/2
from floor to
7-1/2
countertop
2-1/2
2-1/2
30
30
24
31-1/4
24
2-7/8"
To Front
Surface Of
Countertop
20-5/8" Door
Clearance
From Front
Surface of
20-5/8" Door
Countertop
Clearance
From Front
Surface of
Countertop
25-3/4**
25
(excluding handle)
30
Dimension and installation information are shown in inches.
or allow a 24" minimum when bottom of wood or metal cabinet is protected by no less than 1/4"-thick All GE ranges are equipped with
flame-retardant millboard covered with no less than No. 28 MSG sheet metal (.015" thick), .015"-thick an Anti-Tip device. The installation
If the countertop area is not flat, excess tension may be applied to the glass cooktop causing breakage
of this device is an important,
stainless steel, .025" aluminum or .020" copper.
and voiding the warranty. Make sure the wall covering, countertop, flooring and cabinets around the range
required step in the installation
can withstand the heat (up to 200°F) generated by the range.
of the range.
a minimum 6" spacing to surfaces less than 15" above the cooktop and adjacent cabinetry is
A. Allow 30" minimum clearance between surface units and bottom of unprotected wood or metal cabinet,
recommended to reduce exposure to steam, grease splatter and heat. Allow 1/4" minimum clearance
or allow a 24" minimum when bottom of wood or metal cabinet is protected by no less than 1/4"-thick
at the back wall.
flame-retardant millboard covered with no less than No. 28 MSG sheet metal (.015" thick), .015"-thick
stainless steel, .025" aluminum or .020" copper.
B. This appliance has been approved for 0" spacing to adjacent surfaces above the cooktop. However,
a minimum 6" spacing to surfaces less than 15" above the cooktop and adjacent cabinetry is
recommended to reduce exposure to steam, grease splatter and heat. Allow 1/4" minimum clearance
at the back wall.
To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage space above
Shave Raised Edge To Clear
31-1/8" Wide Control Panel
Excluding Models JSS28 and JSP39
9/16
13" Max.
15" Min.
25
7-1/2
2-1/2
Accessory
Backguard
Accessory
Backguard
A/B*
A/B*
31-1/4
36-1/4
36-1/4
*JXS37 is 5-1/4" and JXS32 is 4"
**Total depth from wall to
front of closed oven door
including handle is 27-13/16.
*JXS37 is 5-1/4" and J
25-3/4**
(excluding handle)
**Total depth from wall
front of closed oven d
including handle is 27
Listed by
Underwriters
Laboratories
Specification Revised 6/10
320641