GE JGSP28BEKBB Dimensions And Installation Information

JGSP28WEK/CEK/BEK
GE 30" Slide-In Gas Range
®
Dimensions and Installation Information (in inches)
You must use the rear filler strip kit shipped with
the range or the optional accessory backguard
when installing these ranges
Note: Cabinets installed adjacent to slide-in
ranges must have an adhesion spec of at least
194° temperature rating.
Optional Kits for Slide-In Gas Ranges:
(Available at additional cost)
Lower/Side Trim Kits
JXS56BB - Lower Trim Kit (Black)
JXS56WW - Lower Trim Kit (White)
JXS56CC - Lower Trim Kit (Bisque)
JXS77BB - Side Trim Kit (Black)
JXS77WW - Side Trim Kit (White)
JXS77CC - Side Trim Kit (Bisque)
Accessory Backguards
JXS32BB (Black) - 4" High JXS32SS (Stainless) - 4" High
JXS32CC (Bisque) - 4" High JXS32WW (White) - 4" High
JXS37BB (Black) - 5-1/4" High
JXS37CC (Bisque) - 5-1/4" High
JXS37WW (White) - 5-1/4" High
Installation Information: Before installing, consult
installation instructions packed with product for
current dimensional data.
For answers to your Monogram, ® GE Profile
GE ® appliance questions, visit our website at
ge.com or call GE Answer Center ®
800.626.2000.
26-5/8*
(excluding handle)
5-5/8"
to front
surface of
countertop
20-5/8"
door clearance from
front surface of countertop
*Total depth from wall to
front of closed oven door
including handle is 29-5/8.
™ or
service,
20-5/8"
door clearance from
front surface of countertop
*Total depth from wall to
front of closed oven door
including handle is 29-5/8.
Follow instructions
packaged with
alternate appliance
6" min. from walls
For optimum
installation
these surfaces
must be flat
and level
31-1/4
Max. depth
of cord, plug,
35-7/8"
recept. box &
to 38" from
gas hookup
floor to
4" to prevent
countertop
interference
with drawer
Counter Cutout Dimensions (in inches)
If you are NOT using the
Follow instructions
optional Filler or Backguard:
packaged with
alternate appliance
6" min. from walls
For optimum
23-3/16
24" min.
installation
these surfaces
must be flat
and level
23-3/16
30
Max. depth
of cord, plug,
35-7/8"
recept. box &
to 38" from
gas hookup
floor to
4" to prevent
countertop
interference
with drawer
2-1/2
29-15/16" min.
30-1/16" max.
30" min.
30" min. to
24" min.
unprotected
cabinet from
countertop
13" max.
23-3/16
depth
Countertop depth 25" (typical)
2-1/2
7-1/2
25
29-15/16" min.
2-1/2
30-1/16" max.
Acceptable gas line and
electrical outlet area
If you are using the optional
30" min.
Filler or Backguard:
30" min. to
25
unprotected
cabinet from
countertop
13" max.
18" min. vertical distance
depth
from the bottom of the
adjacent overhead cabinets
30
Countertop depth 25" (typical)
All GE ranges are equipped with
an Anti-Tip device. The installation
of this device is an important,
1-1/4" min. countertop
required step in the installation
to top of drawer
of the range.
7-1/2
25
2-1/2
Acceptable gas line and
electrical outlet area
18" min. vertical distance
from the bottom of the
adjacent overhead cabinets
1-1/4" min. countertop
to top of drawer
Listed by
Underwriters
Laboratories
R
Specification Revised 12/06
330228