Dyson cyclone v10 User Manual page 19

EN
USING YOUR DYSON MACHINE
PLEASE READ THE 'IMPORTANT SAFETY INSTRUCTIONS' IN YOUR
DYSON USER MANUAL BEFORE PROCEEDING.
INSTALLING YOUR DOCKING STATION
• Unpack the docking station, charger and installation leaflet.
• Choose a suitable location for the docking station and make sure there
is no pipework (gas, water or air), electrical cables, wires or ductwork
directly behind the mounting location.
• Don't locate the docking station near a heat source such as a cooker,
radiator or in direct sunlight.
• Follow the instructions on the installation leaflet.
• Click the tools into place on the docking station.
• Place the machine into the docking station.
• Plug the charger into the mains electricity supply. Switch on (if
necessary) to charge the battery.
Your machine will need to be fully charged before first use.
The docking station must be mounted in accordance with regulations
and applicable codes/standards (state and local laws may apply).
Dyson recommends the use of protective clothing, eyewear and
materials when installing the docking station.
USING YOUR MACHINE
• Remove the appliance from the docking station.
• Check that the underside of the cleaner head or tool is clean and free
from foreign objects that may cause damage.
Before vacuuming your flooring, rugs and carpets, check the
manufacturer's recommended cleaning instructions.
The brush bar on the machine can damage certain carpet types and
floors. Some carpets will fuzz if a rotating brush bar is used when
vacuuming. If this happens, we recommend vacuuming without the
motorised floor tool and consulting with your flooring manufacturer.
LIGHTS DURING CHARGING
Charging, low charge
Charging, medium charge
Charging, nearly full
Fully charged
LIGHTS DURING USE
High level of charge
Medium level of charge
Low level of charge
Empty, needs charging
LIGHTS DIAGNOSTICS
Battery fault - call the Dyson Helpline
Main body fault - call the Dyson Helpline
Charger fault - call the Dyson Helpline
FILTER WASH AND BLOCKAGE INDICATOR LEDS
Blockage indicator
Filter unit not fitted correctly
Filter unit requires washing
See battery section
EMPTYING YOUR CLEAR BIN
• Empty as soon as the dirt reaches the MAX level – don't overfill. Using
the machine when the dirt is above the MAX line may cause the dirt to
reach the filter and more frequent maintenance will be required.
• Ensure that the appliance is disconnected from the charger before
emptying the clear bin. Be careful not to pull the 'ON' trigger.
• The 'ON' trigger cannot be operated while the clear bin is open
for emptying.
• Press the red wand release button and pull the wand away from
the bin.
• To release the dirt:
– Hold the machine over a bin in a downwards position.
– Firmly push the red bin release button. The bin will slide down,
cleaning the shroud as it goes and the bin base will open.
– The bin base won't open if the red bin release button isn't pushed
down all the way.
To minimise dust contact when emptying, encase the clear bin tightly
in a dust proof bag and empty. Remove the clear bin carefully from the
bag. Seal the bag tightly and dispose. Remove the clear bin carefully
from the bag. Seal the bag tightly and dispose.
CLEANING YOUR CLEAR BIN
If it is necessary to clean your clear bin, empty the bin as shown in the
'Emptying your clear bin' section.
• Press the red button located on the bin runner to release the bin and
slide the bin off the runner.
• Clean the clear bin with a damp cloth only.
• Make sure that the clear bin and seals are completely dry
before replacing.
• To refit the clear bin:
– Insert the spine on to the bin runner.
– Close the clear bin by pushing the bin base upwards until the clear
bin and bin base click into place.
The clear bin is not dishwasher safe and the use of detergents, polishes
or air fresheners to clean the clear bin is not recommended as this may
damage your machine.
FILTER AND BLOCKAGE INDICATOR LEDS
Your appliance has two indicator lights that will alert you when simple
maintenance steps are needed.
• The filter indicator will flash intermittently when the filter unit is not
fitted correctly. Follow the instructions on how to refit the filter unit in
the 'Washing the filter unit' section.
• The filter indicator will light continuously when the filter unit needs
washing. Follow the instructions on how to wash the filter unit in the
'Washing the filter unit' section.
19