Related Manuals for THOMSON ST2022 SIP
Summary of Contents for THOMSON ST2022 SIP
- Page 1 Thomson Telecom S.A.S with a capital of 130 037 460 € RCS 390 546 059 Copyright © THOMSON 2005 All rights reserved 09/2005 - 1 www.speedtouchpartner.com...
- Page 2 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility. Thomson Telecom declares that this ST2022 MGCP IP Phone is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. You can download the declaration of conformity on www.speedtouchpartner.com.
-
Page 3: Table Of Contents
PRODUCT OVERVIEW AND CONNECTIONS .............. 4 ..........................4 ONNECTIONS PC................. 4 ONNECTING TO THE ETWORK AND THE ....................... 5 OWERING UP THE HONE ........................5 ONNECTED A HEADSET ........................6 HYSICAL EATURES ............................. 6 SER PANEL ................E ISPLAY KEYS RREUR IGNET NON DEFINI .................. -
Page 4: Product Overview And Connections
I. Product overview and connections Connections ST 2022 (Arrière) (a)Transformateur Combiné (b)Ordinateur (c)Réseau Connecting to the Network and the PC The ST2022 MGCP IP Phone has 2 RJ-45 ports that each support 10/100 Mbps full duplex Ethernet connection to external devices- Network port and access port (one for PC and one for LAN). -
Page 5: Powering Up The Phone
Access port (10/100PC) Use the Ethernet cable to connect a network device, such as a computer to the PC port on the back of your phone. Powering up the Phone The ST2022 could be powered by either a main power unit, or PoE. Its power consumption is under 6W. -
Page 6: Physical Features
Physical Features User panel Softkey Handset Navigator keys Phonebook Menu Key Voicemail Clear Key Dial Pad Volume Line/Memory Keys... -
Page 7: Definitions Of Led
Definitions of LED LED Indicator Condition Color Status Default Speaker During FW boot Loudspeaker is activated during a call Default Voicemail During FW boot Voicemail received Slow blinking Default Mute During FW boot Mute is active Default During FW boot Used for speed dial keys in standby mode Feature keys Line appearance: standby mode... -
Page 8: Configuration Through Lcd
II. Configuration through LCD Assign an IP address to the phone Setting the address Using Fix IP address menu Press key. with softkeys. Choose Admin Input Password: The phone will prompt Make sure you have selected the right entry mode with the A>a>1 softkey. - Page 9 softkey Press Wait for ST2022 to reboot The new IP address is set Check that the IP address is set properly Using DHCP menu Press key. with softkeys. Choose Admin Input Password: The phone will prompt Make sure you have selected the right entry mode with the A>a>1 softkey.
-
Page 10: Check That The Ip Address Is Set Properly
Check that the IP address is set properly menu Press softkeys Choose User with Navigator keys Information Use the to scroll down the menu to softkey Press Select The IP address is displayed Once you know the IP address of the ST2022, you can start to configure the phone using its friendly web interface. -
Page 11: Configure Phone Using Web Interface
III. Configure phone using web interface Find the phone IP address menu Press softkeys Choose User with Navigator keys Information Use the to scroll down the menu to softkey Press Select The IP address is displayed Access to Admin Homepage (web interface) Open a web browser (Firefox, Internet Explorer, Safari…) Enter the ST2022 IP address in the address bar with /admin.html appended at the end of it. -
Page 12: S C A
Enter the administrator password (default value is 784518) You will access the Homepage of the ST2022 Setup the SIP configuration Once connected to the ST2022 Admin Homepage, go to the Utility page (Click on SETUP on the top menu of the Homepage. You will access the Setup Page... - Page 13 Click on Basic Setup in the left menu You will access the Setup – Basic Setup page...
- Page 14 Click on the Edit button of the profile you want to edit. You will access the Profile Setup page.
- Page 15 Fill in the SIP Servers properties and the User Accounts Click on Apply...
-
Page 16: Upgrade Firmware
Your changes have been taken into account Upgrade firmware Once connected to the ST2022 Admin Homepage, go to the Setup page (Click on UTILITY on the top menu of the Homepage. You will access the Utilities Page... - Page 17 Click on Firmware Update You will access the Utilities – Firmware Update page...
- Page 18 Browse to find the firmware file you want to upload Click on Apply...
- Page 19 The ST2022 will upload the firmware...
- Page 20 When the firmware file will be uploaded, the ST2022 will ask you to confirm the restart.
- Page 21 Click on Telephone Configure You will access the Utilities – Telephone Configure page Browse to find the TelConf file associated to the firmware Click on Apply When the TelConf file will be uploaded, the ST2022 will ask you to confirm the restart. Click on Restart.