Advertisement
OPERATION
1
2
6
D D U U A A L L B B I I N N N N A A C C L L E E E E V V I I N N R R U U D D E E I I C C O O N N I I I I
C C O O N N T T R R O O L L
1. Master Trim/tilt switch
2. Gear position indicators
3. Individual engine trim switches
4. SYNC button
5. Mode button
6. RPM Tune button
S S h h i i f f t t i i n n g g
With the engine running and the con-
trol handle in the NEUTRAL position,
move the control handle forward or aft
until the handle engages the forward
or reverse gear detent.
S S p p e e e e d d C C o o n n t t r r o o l l
After gear engagement, move the
control handle slowly in the same di-
rection to increase speed.
Press the RPM + or – button to fine
tune engine speed up or down in 1%
increments.
E E n n g g i i n n e e S S y y n n c c h h r r o o n n i i z z a a t t i i o o n n ( ( D D u u a a l l
B B i i n n n n a a c c l l e e O O n n l l y y ) )
Press the SYNC button to automati-
cally synchronize the RPM of multiple
engines. The SYNC button also trans-
fers control of all engines to the port
lever on the control.
N N O O T T I I C C E E
S S Y Y N N C C w w i i l l l l n n o o t t m m a a t t c c h h e e n n g g i i n n e e R R P P M M
u u n n d d e e r r t t h h e e f f o o l l l l o o w w i i n n g g c c o o n n d d i i t t i i o o n n s s : :
– NEUTRAL throttle is active
32
3
4
5
– Port Engine speed is below 700
RPM
– Port Throttle setting is above 95%
– A critical fault is set
E E v v i i n n r r u u d d e e M M e e c c h h a a n n i i c c a a l l C C o o n n t t r r o o l l s s
W W A A R R N N I I N N G G
I I f f y y o o u u c c h h o o o o s s e e a a n n o o n n - - E E v v i i n n r r u u d d e e r r e e - -
m m o o t t e e c c o o n n t t r r o o l l , , i i t t m m u u s s t t h h a a v v e e a a s s t t a a r r t t - -
i i n n - - g g e e a a r r p p r r e e v v e e n n t t i i o o n n f f e e a a t t u u r r e e . . T T h h i i s s
f f e e a a t t u u r r e e c c a a n n p p r r e e v v e e n n t t i i n n j j u u r r i i e e s s r r e e - -
s s u u l l t t i i n n g g f f r r o o m m u u n n e e x x p p e e c c t t e e d d b b o o a a t t
m m o o v v e e m m e e n n t t w w h h e e n n t t h h e e e e n n g g i i n n e e
s s t t a a r r t t s s . .
Use of a mechanical remote control
requires an accessory mechanical to
digital shift and throttle converter.
I I M M P P O O R R T T A A N N T T : : When selecting the re-
mote control system for your boat,
specify Evinrude components. Evin-
rude controls incorporate safety and
convenience features as:
– Start-in-gear prevention
– Plug-in compatibility with Evinrude
Modular Wiring System (MWS).
3
5
S S I I D D E E M M O O U U N N T T C C O O N N T T R R O O L L
1. Handle – shift and throttle
2. Trim/tilt switch (where equipped)
3. Neutral lock lever
4. Fast idle lever (warm-up)
5. Throttle friction adjusting screw
6. Engine cut–off switch clip and tether cord
2
1
4
6
Advertisement
