Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ricoh PB2030
Summary of Contents for Ricoh PB2030
- Page 1 Paper Feed Unit PB2030/2040 Machine Code: D3F1 Installation Procedure Initial Release: December, 2018 (c) 2018 Ricoh Co., Ltd. NOTE: THIS UNIT MUST BE INSTALLED BY A CUSTOMER SERVICE REPRESENTATIVE WHO HAS COMPLETED THE TRAINING COURSES ON THE BASE MACHINE AND THE UNIT.
- Page 3 Symbols and Abbreviations This manual uses the following symbols and abbreviations: Symbols: Screw Black screw Connector Flexible flat cable (FFC) Hook Clamp Clip ring E-ring C-ring Timing belt Spring Location of a screw(s) to be tightened or loosened. Location of a connector(s), clamp(s) or spring(s) to be removed Direction (Rotating or moving) Abbreviations: Abbreviations such as (M1), (S1), or (TH1) after the names of some electrical components indicates...
-
Page 5: Table Of Contents
Table of Contents Installation Requirements ........................2 Environment ............................2 Machine Level............................3 Minimum Space Requirements ......................4 Power Requirements ..........................5 Accessory Check ..........................6 Installation Procedure ......................... 7 Installing the Single Paper Feed Unit ..................... 7 Installing the Double Paper Feed Unit ....................12... -
Page 6: Installation Requirements
1.Installation Requirements 1. Installation Requirements Environment –Temperature and Humidity Chart– 10 - 32°C (50 - 89.6°F) Standard temperature range: • 15% to 80% RH • Standard humidity range: 10 - 38°C (50 - 100.4°F) Extended temperature range: • 10% to 90% RH Extended humidity range: •... -
Page 7: Machine Level
1.Installation Requirements Machine Level Front to back: Within 5 mm (0.2") of level Right to left: Within 5 mm (0.2") of level... -
Page 8: Minimum Space Requirements
1.Installation Requirements Minimum Space Requirements Place the machine near a power source, providing clearance as shown: A (front): 750 mm (30") B (left): 150 mm (6") C (rear): 300 mm (12") D (right): 450 mm (18") The recommended 750 mm (30") front space is sufficient to allow the paper tray to be pulled out. Additional front space is required to allow operators to stand at the front of the machine. -
Page 9: Power Requirements
1.Installation Requirements Power Requirements • Make sure that the wall outlet is near the machine and easily accessible. After completing the installation, make sure the plug is firmly inserted into the outlet. • Avoid using extension cables. Input voltage: EU, AP, CHN 220V - 240V, 50/60Hz, 8A... -
Page 10: Accessory Check
2.Accessory Check 2. Accessory Check Check the quantity and condition of the accessories against the following list. Description Q’ty Relay harness Screws... -
Page 11: Installation Procedure
3.Installation Procedure 3. Installation Procedure • Turn off the main power switch of the main machine and unplug the power cord before starting the installation procedure. • Two or more people are required to lift the main machine. The main machine is highly unstable when lifted by one person, possibly resulting in injury or property damage. - Page 12 3.Installation Procedure Remove the rear cover of the main machine [A]. Remove the rear cover [A] of the paper feed unit.
- Page 13 3.Installation Procedure Remove the brackets [A] on the bottom of the main machine. Insert the relay harness into the opening [A] of the main machine. Connect the relay harness provided with the paper feed unit to the bottom connector [A] and...
- Page 14 3.Installation Procedure CN246 [B] on the MPU (PCB7) board. Pull out the paper trays [A] and [B]. 10. Secure the main machine to the paper feed unit. Screws (M4 x 6) are provided with the paper feed unit. Use a stubby driver or the bracket wrench [A] attached to the rear bottom of the paper feed unit. Reattach the bracket wrench after tightening the screws.
- Page 15 3.Installation Procedure 11. Reinstall all trays and covers. 12. Load paper into the paper feed unit. 13. Turn on the main power switch of the machine. 14. Adjust the registration of the upper paper feed unit. (Adjustment after Replacement) • Use SP1-002-004 for the tray bank 1.
-
Page 16: Installing The Double Paper Feed Unit
3.Installation Procedure Installing the Double Paper Feed Unit Remove all tapes and accessories on the paper feed unit. Pull the tray, and then remove the filament tapes and paddings. Lift the main machine and place it on the paper feed unit. - Page 17 3.Installation Procedure Remove the rear cover of the main machine [A]. Remove the rear cover [A] of the paper feed unit.
- Page 18 3.Installation Procedure Remove the brackets [A] on the bottom of the main machine. Insert the relay harness into the opening [A] of the main machine. Connect the relay harness provided with the paper feed unit to the bottom connector [A] and...
- Page 19 3.Installation Procedure CN246 [B] on the MPU (PCB7) board. Pull out the paper trays [A] and [B]. 10. Secure the main machine to the paper feed unit. Screws (M4 x 6) are provided with the paper feed unit. Use a stubby driver or the bracket wrench [A] attached to the rear side of the paper feed unit.
- Page 20 3.Installation Procedure Reattach the bracket wrench after tightening the screws. 11. Reinstall all trays and covers. 12. Load paper into the paper feed unit. 13. Turn on the main power switch of the machine. 14. Adjust the registration of the upper paper feed unit. (Adjustment after Replacement) Use SP1-002-005 for the tray bank 2.