Dyson Cyclone v10 Operating Manual page 19

EN
USING YOUR DYSON APPLIANCE
PLEASE READ THE 'IMPORTANT SAFETY INSTRUCTIONS' IN THIS
DYSON OPERATING MANUAL BEFORE PROCEEDING.
DOCKING STATION INSTALLATION
• Unpack the docking station, plug and installation leaflet.
• Select the location for the docking station and ensure that there is no
pipework (gas, water or air), electrical cables, wires or ductwork directly
behind the mounting location.
• Follow the instructions on the Installation leaflet.
• Click the attachments into place.
• Place the appliance in the docking station.
• Plug in the docking station and turn on to charge.
• Your appliance will need to be fully charged before first use.
The docking station must be mounted in accordance with regulations
and applicable codes/standards (state and local laws may apply).
3
Dyson recommends the use of protective clothing, eyewear and
materials when installing the docking station.
VACUUMING
• Remove the appliance from the docking station.
• Check that the underside of the cleaner head or tool is clean and free
from foreign objects that may cause damage.
Before vacuuming your flooring, rugs and carpets, check the
manufacturer's recommended cleaning instructions.
The brush bar on the appliance can damage certain carpet types
and floors. Some carpets will fuzz if a rotating brush bar is used when
vacuuming. If this happens, we recommend vacuuming without the
motorised floor tool and consulting with your flooring manufacturer.
LIGHTS DURING CHARGING
Charging, low charge
Charging, medium charge
1 Charging, nearly full
Fully charged
LIGHTS DURING USE
High level of charge
4
Medium level of charge
Low level of charge
Empty, needs charging
LIGHTS DIAGNOSTICS
7
Battery fault-call Dyson Helpline
Main body fault-call Dyson Helpline
Charger fault-call Dyson Helpline
06.09.2017 07:40 - C87672_SV12_OPMAN_FEAST_X248-V10-ABSOLUTE-OPMAN-87672.indd_15_4c0s
1
4
2
5
8
clik
clik
FILTER WASH AND BLOCKAGE INDICATOR LEDS
Blockage indicator
2
Filter unit requires washing
Filter unit not fitted correctly
See battery section
5
EMPTYING THE CLEAR BIN
• Empty as soon as the dirt reaches the level of the MAX mark – do
not overfill.
• Ensure that the appliance is disconnected from the charger before
emptying the clear bin. Be careful not to pull the 'ON' trigger.
• Avoid pulling the "ON" trigger when emptying.
• Remove the wand by pressing the red wand release button and pulling
away from the bin.
• To release the dirt:
– Hold the appliance with the bin in a downwards position.
– firmly push the red bin release button.
– The bin will slide down, cleaning the shroud as it goes.
– The bin base will then open.
– The bin base will not open if the red button is not pushed down fully.
To minimise dust contact when emptying, encase the clear bin tightly in a
plastic bag and empty. Remove the clear bin carefully from the bag. Seal
the bag tightly, dispose as normal.
CLEANING THE CLEAR BIN (OPTIONAL)
If it is necessary to clean the clear bin: 3
• Follow the instructions in the "Emptying the clear bin" section.
• Press the red button located on the bin runner to release the bin and slide
the bin off the runner.
• Clean the clear bin with a damp cloth only.
• Ensure that the clear bin and seals are completely dry before replacing.
• To refit the clear bin:
– Insert the spine on to the bin runner.
Close the clear bin by pushing the bin base upwards until the clear bin
and bin base click into place.
The clear bin is not dishwasher safe and the use of detergents, polishes
or air fresheners to clean the clear bin is not recommended as this may
damage to your appliance.
FILTER AND BLOCKAGE INDICATOR LEDS
Your appliance has two indicator lights that will help alert you that simple
6
maintenance steps are needed.
• The filter indicator will flash intermittently when the filter unit is not
fitted correctly. Follow the instructions on how to refit the filter unit in the
'Washing the filter unit' section.
• The filter indicator will light continuously when the filter unit needs
washing. Follow the instructions on how to wash the filter unit in the
'Washing the filter unit' section.
• The blockage Indicator LED will light if there is a blockage. Follow the
instructions on how to clear blockages in the 'Looking for blockages'
section.
WASHABLE PARTS
Your appliance has washable parts, which require regular cleaning.
Follow the instructions below.
WASHING THE BRUSH BARS
Your appliance has two washable brush bars, check and
wash these regularly according to the following instructions to
maintain performance.
• Ensure the appliance is disconnected from the charger before removing
the brush bar. Be careful not to pull the 'ON' trigger.
To remove, wash and replace brush bars:
• Please refer to the 'Washing the brush bars' illustrations alongside the
instructions below.
• Turn the cleaner head upside down so the underside of the cleaner head
is facing you. Use a coin to turn the fastener one quarter anti-clockwise
until it clicks into the unlocked position.
• Rotate the end cap to the open position. Gently slide the large brush bar
away from the cleaner head.
• Remove the end cap from the large brush bar. Do not wash the end cap.
• Lift out the small brush bar from the octagonal end and pull away from
the cleaner head.
• Hold the brush bars under running water and gently rub to remove any
lint or dirt.
9
19