1. Manuals
  2. Brands
  3. Record Manuals
  4. Door Opening System
  5. system 20
  6. Translation of the original manual

Record system 20 Translation Of The Original Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

record system 20
Translation of the original manual

Advertisement

Table of Contents
loading

Related Manuals for Record system 20

Summary of Contents for Record system 20

  • Page 1 20 Translation of the original manual...

  • Page 2: Table Of Contents

    Table of contents Table of contents Table of revisions ..................... General information ..................Book 8 / Document identification ....................Structure of the documentation ...................... Purpose and use of the instructions ....................Parameter explanations V2.1_V2.6 ..............Parameter overview V2.1_V2.6 ................. Parameter overview STM 20, STG 20 UNI, STM 20 DUO, STM 22 DUO ........Parameter overview STM 20 RED, STM 22 RED ................

  • Page 3: Table Of Revisions

    Table of revisions Table of revisions Book 8 / Document identification New Version V2.2 ............4 Parameter explanations V2.1_V2.6 Newr Parameter FlowControl ........6 Parameter overview V2.1_V2.6 STM20 RED, STM22 RED, STM21 RED Version V2.6 ................47 IRA_B8_EN_2V2_REC_102-020401137 3/ 56...

  • Page 4: General Information

    General information General information Book 8 / Document identification Name: IRA_B8_EN_2V2_REC_102-020401137 Version: V2.2 Article nr.: 102-020401137 Publication date: 07/2020 Structure of the documentation The documentation is divided into different manuals in order to reduce file size and to simplify the handling.

  • Page 5: Purpose And Use Of The Instructions

    General information Purpose and use of the instructions These instructions are an integral part of the system and enable the efficient and safe handling of the system. Although only the male form has been chosen for reasons of better legibility, the information refers to members of both sexes.

  • Page 6: Parameter Explanations V2.1_V2.6

    Parameter explanations V2.1_V2.6 Parameter explanations V2.1_V2.6 PARAMETER COMMENT DRIVING CYCLE → Opening speed Driving speed of the opening door. 0 = lowest speed 40 = highest speed ▪ The maximum reachable speed depends on the driven distance (door width) and the acceleration setting. ▪...
  • Page 7 Parameter explanations V2.1_V2.6 → Creep section Ending creep section while closing. 0 = no creep section 1 = creep on the last 2.5% of travel way 40 = 100% creep on 100% of travel way ▪ The creep section is calculated on the basis of the maxi- mum opening distance driven.
  • Page 8 Parameter explanations V2.1_V2.6 Seal Setting for doors with special wide and strong seal in the clos- ing area, e.g. for OP doors. 0 = no seal 1 = 10 cm wide sealing area … = approx. 0.5 mm increments 40 = 30 mm wide sealing area ▪...
  • Page 9 Parameter explanations V2.1_V2.6 Reset with button Enables an early closing of the door by sending the same opening signal again during the hold-open time. This function is usually implemented with OP doors. Disabled No interruption of the hold-open time. Enabled Hold-open time can be interrupted with one of the signals from the same group: Group 1: AKI button, AKA button...
  • Page 10 Parameter explanations V2.1_V2.6 → Reduced opening width With RED doors, this parameter helps configure the Escape (with RED) route width. This is normally specified by each country’s build- ing inspection and can also be shared for several doors. 0 = minimum opening width 40 = total opening width ▪...
  • Page 11 Parameter explanations V2.1_V2.6 Open position If the door has reached the planned opening width, pull the brake in all operating modes. This is also valid in case of re- duced opening width. ▪ If the door stops e.g. due to safety signals or because of a collision, the brake is not activated.
  • Page 12 Parameter explanations V2.1_V2.6 Two motors This parameter indicates whether one or two motors are con- nected to the STM. Normally, the second motor is automatical- ly identified. ▪ Two motors can only be configures if the STM has been planned accordingly (DUO). ▪...
  • Page 13 Parameter explanations V2.1_V2.6 → Power failure This parameter determines the behaviour of the door controller after a power failure. → Battery operation In case of sufficient battery capacity, the door goes on func- tioning as before the power failure. However, the door is oper- ated with reduced acceleration to preserve the battery capaci- ty.
  • Page 14 Parameter explanations V2.1_V2.6 → Interlock Two doors, each fitted with function extension module FEM1, can be interconnected in an interlock system. The parameter determines in which operating modes the interlock function is enabled. ▪ Interlock not possible with RED doors and STM21. ▪...
  • Page 15 Parameter explanations V2.1_V2.6 → RED battery Standard setting for escape route doors. ▪ This door type can only be selected for redundant control units with appropriate software. ▪ Standard and emergency channels are checked at least every 24 hours for correct functioning. Normally, the re- dundancy test occurs after approx.
  • Page 16 Parameter explanations V2.1_V2.6 FlipFlow Folding door application with double swing leaf (DDF). ▪ Increased force and speed when closing. ▪ NSK/SÖK speed is adjustable. Attention: Safety signals are not monitored. Increasing the speed reduces personal safety at the expense of e.g. building security. ▪...
  • Page 17 Parameter explanations V2.1_V2.6 Input/Output → STG → SÖK:NSK → Speed Miscellaneous → Alarm display → Time activation → CO48 Sandow direct Door with integrated rubber cord (power storage). ▪ For 108/150 mm drives ▪ Only for motors with brake ▪ In France no batteries are allowed ▪...
  • Page 18 Parameter explanations V2.1_V2.6 → Breakout USA Door type for the USA ▪ Default parameters: Parameter Default value Input/Output → EMERG. STOP Disabled Reset Miscellaneous → Alarm display Enabled → Collision → Ratchet Door controlled by a single key for USA applications (garage door control).
  • Page 19 Parameter explanations V2.1_V2.6 Dead man → Dead man Door controlled by two keys with behaviour, i.e. the door only slides as long as the OPENING or CLOSING key is continuously pressed (24V on signal input). ▪ If the CLOSING and OPENING buttons are pressed at the same time, the door stops.
  • Page 20 Parameter explanations V2.1_V2.6 → 3 buttons Door controlled by three keys – a key to open, a key to close and a key to stop the door. ▪ One pulse 0V 24V with the AKI button opens the door up to the opening width.
  • Page 21 Parameter explanations V2.1_V2.6 Driving cycle → Open → Creep section Time delay open → Time delay Drive → Collision close Control unit → BDE-D → Select language → Français Control unit → Default operat- ing mode → Automatic Output → AUX0_OUT → Fault output →...
  • Page 22 Parameter explanations V2.1_V2.6 → OP door 2 Button-operated door for the hermetic closing of an operating room. ▪ Default parameters: Parameter Default value Driving cycle → Ramp → Sec- tion Driving cycle → Seal For more parameters, see OP door 1 Basic escape route →...
  • Page 23 Parameter explanations V2.1_V2.6 Input/Output → SIO → Function Stop Miscellan. → Alarm display → Enabled Collision → Folding door USA Folding door for the USA with various adjustments. CONTROL PANEL → BDE-M Selection of the mechanical control unit. ▪ The selection depends on the STM variant and software version.
  • Page 24 Parameter explanations V2.1_V2.6 → Analogue BDE-A Mechanical BDE for USA. BDEM_1 Opening width Complete opening width Reduced opening width BDEM_2 Operating mode approx. 2.5V approx. 7.5V Continuously open approx. 13V One-Way approx. 19V Automatic → Standard Reduced BDEM_2 BDEM_1 Oper. mode Open.
  • Page 25 Parameter explanations V2.1_V2.6 → Contrast BDE 1 Contrast of the display screen for 1st BDE-D. 0 = high contrast, possible streaking 40 = low contrast, display is faintly visible → Contrast BDE 2 Contrast of the display screen for 2nd BDE-D. →...
  • Page 26 VRR 20 (motor-powered, bi-stable) → Bi-stable VRR 16 (magnetic, bi-stable) → MPV 20 Multipoint locking device for system 20 (motor-powered) → MPV 16 Multipoint locking device for system 16 (motor-powered) → Magnet Magnet locking device (without VAK) unlocked without current (mono-stable) →...
  • Page 27 Parameter explanations V2.1_V2.6 CAN BUS In this menu all the units identified on the CAN BUS – such as sensors or extended function modules – are displayed. 0 = no unit present or unit unidentified (disabled) 1 = unit installed and functional (enabled) ? = unit defective or missing ▪...
  • Page 28 Parameter explanations V2.1_V2.6 INPUT/OUTPUT → STG (0V) in safety-relevant signals (e.g. SIS) means that the → BDE_V1 signal has triggered. (only STM20/22 DUO) ▪ Normally, signals for connecting buttons only react to the → BDE_V2 signal change over (0V 24V). Thus, for example, the door can be opened with the AKI button, but will automatically (only STM20/22 DUO) shut at the end of the hold-open time, even though the but-...
  • Page 29 Parameter explanations V2.1_V2.6 → SIS Safety signal in closing direction. 0V/open = security active 24V = security passive ▪ An open door only closes when the signal is passive. ▪ If the signal becomes active during a closing movement the door reverses, stops or creeps (configuration with rameter →...
  • Page 30 Parameter explanations V2.1_V2.6 → Broken rubber cord Monitoring of the rubber cord with door type CO48. 0V/open = rubber cord broken (switch open) 24V = rubber cord fine (switch closed) ▪ In case of torn cord, error 20 is displayed and the door opens to the full opening width, provided that it is not locked.
  • Page 31 Parameter explanations V2.1_V2.6 → CLOSING button Closing of the door with pulse signal (0V/open -> 24V) for but- ton-operated door types. ▪ The closing movement is monitored by safety signals (SIS). After losing the SIS signal a new closing pulse is necessary.
  • Page 32 Parameter explanations V2.1_V2.6 → VRR manually Signal for connecting a rod lock (manual locking). 0V/open = rod lock closed 24V = rod lock open ▪ If the lock is closed (0V/open) the door can be moved freely in a similar way to manual mode. The text display of the BDE-D changes alternately between the current oper- Manually locked ating mode and...
  • Page 33 Parameter explanations V2.1_V2.6 ▪ With some sensors the test logic (test pulse 0V 24V or 24V 0V) can be selected at the sensor. If not, the changeover contact of the relay must be connected accordingly. Please, see appropriate overview in chapter 7 of this man- ual.
  • Page 34 No additional p.c.b. is connected. → ELS Additional p.c.b. for 2 ELS is connected. → ZLP-2 (only RED) Additional p.c.b. for RED installations with non-record sensors. Once identified, a ZLP-AKI (automatic recognition) can only be reset manually with the FPC. → Without No additional p.c.b.
  • Page 35 Parameter explanations V2.1_V2.6 → Interior button reduced Opening to reduced opening width with pulse signal (0V/open - (only with RED) > 24V). The signal is intended for connecting a button on the inner side of the door. ▪ May only be used in an addition to a certified escape route sensor.
  • Page 36 Parameter explanations V2.1_V2.6 → TOS DV 1 Turn lock surveillance of door leaf 1 for doors featuring a swiv- elling leaf (door type Manual mode ▪ Switch position and door function ( ) must match up. → TOS DV 2 Turn lock surveillance of door leaf 2 for doors featuring a swiv- elling leaf (door type Manual mode...
  • Page 37 Parameter explanations V2.1_V2.6 → Interlock Configuration for interlock operation. ▪ It is possible to operate the system with sensors between the doors or without sensors with interlock sequential con- trol. Parameter Default value Input → AUX10_IN S_AUS Input → AUX11_IN Input →...
  • Page 38 Parameter explanations V2.1_V2.6 → APS Open-position Opening width in the case of APS control. ▪ Normally, a floor bolt or a second lock is mounted as a protection against burglary attempts. The opening width must be set so that the door stops shortly before impact. Parameter →...
  • Page 39 Parameter explanations V2.1_V2.6 → AUX13_IN Configurable input signal for FEM1 Connector J1, terminals 70 and 71 (only FEM1) Floating, optically disconnected 24V input → Disabled → AUX10_OUT … AUX1D_OUT 14 configurable output signals for FEM1. Connector J2, floating change over contact 30 volt DC / 1 A Normally closed (NC) or normally open (NO) contact (selection via jumper position -->...
  • Page 40 Parameter explanations V2.1_V2.6 → AKI / AKA This output signal indicates that a triggering signal on the inner or outer side of the door is active. ▪ The output connects independently of the current operating mode. → SSK This output signal shows that an SSK signal is active. ▪...
  • Page 41 Parameter explanations V2.1_V2.6 reduced → Reduced OM The relay is active as long as an operating mode with opening width is activated. → Power failure The relay is active as long as there is no mains voltage and the control unit is operated by battery. Parameter →...
  • Page 42 Parameter explanations V2.1_V2.6 INPUT/OUTPUT → AKA_IN This parameter is used to configure for which operating modes the triggering signals on the outside of the door are active. → AKA A closed door can only be opened with an AKA signal in oper- Automatic ating mode (standard behaviour).
  • Page 43 Parameter explanations V2.1_V2.6 → NSK locked Emergency closing with subsequent door locking. ▪ The signal closes the door in all operating modes with highest priority. Then the door is locked. ▪ The door closes at reduced speed, and safety signals are not taken into account during the closing movement.
  • Page 44 Parameter explanations V2.1_V2.6 → SIO Configuration of safety signal in opening direction (SIO). → Function SIO Further driving behaviour after SIO signal. → Stop Stop drive mechanism immediately and cease opening. → Creep Open at reduced speed up to set opening width. →...
  • Page 45 Parameter explanations V2.1_V2.6 → Push to actuate open The door will open automatically when it is slid open manually on approx. 3 mm from the closed position. ▪ This function is not active on a locked door and in operat- One-Way ing mode ▪...
  • Page 46 If the alarm output has been configured, it switches after expiry of the set time. → FlowControl This function of the control module is exclusively for record Red Test limited FlowControl, so that the RED test can be parameterised in the operating mode „One-way“...

  • Page 47: Parameter Overview V2.1_V2.6

    Parameter overview V2.1_V2.6 Parameter overview V2.1_V2.6 Parameter overview STM 20, STG 20 UNI, STM 20 DUO, STM 22 DUO IRA_B8_EN_2V2_REC_102-020401137 47/ 56...
  • Page 48 Parameter overview V2.1_V2.6 IRA_B8_EN_2V2_REC_102-020401137 48/ 56...

  • Page 49: Parameter Overview Stm 20 Red, Stm 22 Red

    Parameter overview V2.1_V2.6 Parameter overview STM 20 RED, STM 22 RED IRA_B8_EN_2V2_REC_102-020401137 49/ 56...
  • Page 50 Parameter overview V2.1_V2.6 IRA_B8_EN_2V2_REC_102-020401137 50/ 56...

  • Page 51: Parameter Overview Stm 21

    Parameter overview V2.1_V2.6 Parameter overview STM 21 IRA_B8_EN_2V2_REC_102-020401137 51/ 56...
  • Page 52 Parameter overview V2.1_V2.6 IRA_B8_EN_2V2_REC_102-020401137 52/ 56...

  • Page 53: Parameter Overview Stm 21 Red

    Parameter overview V2.1_V2.6 Parameter overview STM 21 RED IRA_B8_EN_2V2_REC_102-020401137 53/ 56...
  • Page 54 Parameter overview V2.1_V2.6 IRA_B8_EN_2V2_REC_102-020401137 54/ 56...

  • Page 55: Parameter Overview Fem

    Parameter overview V2.1_V2.6 Parameter overview FEM IRA_B8_EN_2V2_REC_102-020401137 55/ 56...
  • Page 56 Parameter overview V2.1_V2.6 IRA_B8_EN_2V2_REC_102-020401137 56/ 56...
  • Page 57 Great Britain www.recorduk.co.uk Magyarorszag www.record.hu Malaysia www.recorddoors.my Nederland www.recordbv.nl Österreich www.record.co.at Polska pl.record.global Schweiz www.record.ch Slovenija www.record.si Sverige www.record.se Türkiye tr.record.global United States www.recorddoors.com record global export www.record.global record Group www.record.group Subject to technical modifications Copyright © agtatec ag n° 102-020401137...

Table of Contents