Advertisement
Quick Links
Instruction Data | 374-DREM
Elkay easyDALi Remote Control
Installer Instructions
The easyDALI Remote Control consists of eight soft touch
buttons to control the Elkay easyDALi PIR (374-CMPIRDALI)
It can program basic installation and commissioning
functionality and has one hidden button that changes the
remote control from user mode to Installer Mode. Installer
Mode is detailed below but for End User Modes see separate
'End User instructions'.
Installer Modes- How to program your easyDALi system
In Installer mode it is possible to control the timing options and
also select Room and Corridor Options
– Open battery cover at rear and remove paper tab from
battery area to enable the remote
– You must turn lights OFF with the remote first to operate
and program in this mode
– To begin installer mode, remove battery cover at rear and
place pin in hole and press once. Once feed back light goes
RED
you are in Installer Mode
– Installer Mode information should never be given to
End users of the system
Installer mode only
E. Override ON/OFF Button
D. Minimum Arc Power
Sets the minimum level the
harvester will not go below
1. Add group to pre-
addressed luminaires
2. Find pre-addressed
luminaires or address new
uncommitted luminaires
Adjustment
Features
– Dual purpose DALI Remote Control
– For use with Elkay easyDALi system
– User mode for day to day control
– Installer mode for installation set up
Elkay easyDALi Remote Control Instructions must be read in
conjunction with Elkay easyDAli PIR 374-CMPIRDALI
Instructions in order to enable all features of the PIR.
Remote Control Rear View
Small Hole
(Hidden
Installer Button)
A. Feedback LED -
continuous
B. SET Button
C. Mode Options Up and
Mode Options DOWN
Setting room timing options
and Corridor timing options as
per Table 1
4. Reset to Manual controls
3. Update all discovered
luminaires of the current
group with 16 pre-set levels
as scenes.
per ballast then a blue flash to
indicate complete
RED
in Installer Option
For Walk test
16 Green flashes
Advertisement
Summary of Contents for Elkay easyDALi 374-DREM
- Page 1 – Installer mode for installation set up remote control from user mode to Installer Mode. Installer Mode is detailed below but for End User Modes see separate Elkay easyDALi Remote Control Instructions must be read in ‘End User instructions’. conjunction with Elkay easyDAli PIR 374-CMPIRDALI Instructions in order to enable all features of the PIR.
- Page 2 - Initiates Walk Test only in Installer Mode. Walk test can be used to test and setup the Elkay easyDALi PIR sensitivity by moving in & out of the PIRs detection range. The signal LED on the PIR indicates presence by flashing blue and can be used as a basic walk test. During walk test detection the luminaires will be illuminated to full brightness then after a short delay with no presence detection the luminaires will dim but not go off.
- Page 3 - When pushed in Installer Mode the luminaires will stay off even after a power failure or until the override off button is pressed once more. While in override off the signal LED on the Elkay DALI PIR will flash white. Only Elkay DALI PIRs that have been turned to off or hibernate (signal LED flashing white) will accept installer commands.
- Page 4 In a brand new ‘out of the box’ installation of new DALI luminaires and with a new Elkay easyDALI PIR, you can simply wire the lighting, the power supply and the PIR together with the multi-purpose box and simply accept the default settings of…..
- Page 5 ‘Reset to Automatic Daylight Harvesting’ button. While in override off the signal LED on the Elkay DALI PIR 4. 100% Instant Brightness will flash white. Pressing override off again will restore the 5.
- Page 6 X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for manufacturer: Elkay Other Similar products are found below : 370B-1 550B-1 374-DREM 374-DMBOX AQUASAFE 400A 041852X 041854F 041874R 2001/3/CG/3 1278 1275 1276-18 2001/4/CG/4...