Ricoh Pro L5130 Manual
Additional function 2
Hide thumbs
Also See for Pro L5130:
- Rip settings manual (44 pages) ,
- Safety information manual (32 pages) ,
- Quick start quide (32 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ricoh Pro L5130
Summary of Contents for Ricoh Pro L5130
- Page 1 RICOH Pro L5130/5160 RICOH Pro L5130e/5160e Additional Function Manual 2...
-
Page 2: Table Of Contents
Table of Contents Before You Start ........................3 How to Read this Manual ....................3 Added Display of Print Remaining Time and Length ............4 Checking Print Remaining Time and Length ..............4 Added Head Cleaning Function During Printing .............. 6 Performing Head Cleaning During Printing .............. -
Page 3: Before You Start
Before You Start Before You Start How to Read this Manual This document describes additional functions of the new firmware for both RICOH Pro L5130/5160 and RICOH Pro L5130e/5160e. System : 2.04 or later Engine : 2.04:01 or later Updating firmware of the machine should be performed by a customer engineer. Contact your service representative. -
Page 4: Added Display Of Print Remaining Time And Length
Added Display of Print Remaining Time and Length Added Display of Print Remaining Time and Length Checking Print Remaining Time and Length [Overview] Added the new function to display the print remaining time and length on the control panel. [How to operate] ⚫... - Page 5 Added Display of Print Remaining Time and Length ⚫ Print Remaining Length / Total Length The print remaining length / total length is displayed on the "Job" tab of the control panel. Press [Check Status] key during printing. Press [Job] tab. Note: The print remaining length / total length indicate the feed length required for the machine to complete the print.
-
Page 6: Added Head Cleaning Function During Printing
Added Head Cleaning Function During Printing Added Head Cleaning Function During Printing Performing Head Cleaning During Printing [Overview] Added the new function to perform head cleaning during printing. This allows you to clean the head immediately when you find a nozzle missing during printing. [How to operate] Press [Printing Adjustment] during printing. -
Page 7: Added Media Feed Fine Adjustment (Micro Setting) During Printing
Added Media Feed Fine Adjustment (Micro Setting) During Printing Added Media Feed Fine Adjustment (Micro Setting) During Printing Performing Media Feed Fine Adjustment During Printing [Overview] Added the new function to perform Media Feed Fine Adjustment (Micro Setting) during printing. This allows you to make fine adjustments during printing while viewing the printed image, saving you more steps and time than before. -
Page 8: Added Alert Message Of Intermittent Printing
Added Alert Message of Intermittent Printing Added Alert Message of Intermittent Printing Descriptions and Actions for Intermittent Printing [Overview] This printer is recommended for use in Gigabit Ethernet network. If the network environment or RIP PC performance is poor, data transfer to the printer may (*1) be delayed, resulting in "Intermittent Printing"... - Page 9 Added Alert Message of Intermittent Printing ⚫ When the alert message is displayed Stop current printing once and review your network and RIP PC environment. In general, check the following points. If the problem persists, contact your service representative. If "100 Mbps" is selected as the "Ethernet Speed" setting in the "Network Settings" of the printer, change the access speed to "Auto Selection"...
-
Page 10: Added New Drying Operation
Added New Drying Operation Added New Drying Operation Reducing Media Consumption Between Job to Job [Overview] Added the new drying operation to reduce media consumption between jobs. This function described in this chapter is available from the following firmware versions. System : 2.03 or later Engine : 2.03:01 or later [How to operate]... - Page 11 Added New Drying Operation ⚫ Execute Drying After Printing Performs only the drying operation for the undried part of the printed image by following the steps below. Use this feature when you want to dry the undried part of the printed image without printing the next job.
- Page 12 W hen you cut m edi a m ade of har d m at er i al or t hi ck m edi a, use a com m er ci al l y avai l abl e 2014 年 4 月 D3AS-5040 © 2014 Ricoh Co., Ltd. 2014 年 4 月 D3AS-5040 ©...