Behringer X-TOUCH Documentation
Universal control surface, midi documentation
Hide thumbs
Also See for X-TOUCH:
- Quick start manual (65 pages) ,
- Quick start manual (24 pages) ,
- Quick start manual (5 pages)
Advertisement
Table of Contents
- 1 Overview
- 2 Preparing a Connection between the Mixer and Control Surface
- 3 Direct MIDI Connection
- 4 Direct Ethernet Connection
- 5 Connecting the Mixer and Control Surface in LAN/WLAN Infrastructure
- 6 Mode: XCTL
- 7 Main Display
- 8 Channel Section
- 9 Encoder Assign
- 10 Functions
- 11 Mode: XCTL + MCU and XCTL + HUI
- 12 XCTL Operating Mode Description
- 13 Layout Diagram
- Download this manual
Advertisement
Table of Contents
Related Manuals for Behringer X-TOUCH
Summary of Contents for Behringer X-TOUCH
- Page 1 Behringer X-TOUCH Universal Control Surface MIDI Documentation © Music Tribe Global Brands Ltd. All rights reserved. All information in this document is subject to change without any further notice. musictribe.com behringer.com...
- Page 2 XR12, XR16, X18, and XR18. The connection between the X-TOUCH and the mixer can be made via Ethernet connection or MIDI in and out connections. This document shows how to make the connections, and how to use the X-TOUCH in Xctl mode, Xctl + MC mode, and Xctl + HUI mode. Operating Modes:...
- Page 3 You may use all the controls as described in the XCTL Mode overview shown later in this document The next time X-TOUCH is started, it will automatically attempt to connect to the mixer with the speci ed Slv IP address again. If it does not connect automatically, go back to step 7d music-group.com...
- Page 4 “Wi Client” when registering on a wireless network infrastructure Connect your X-TOUCH to the network router/switch using a CAT5 Ethernet cable Hold down the X-TOUCH CH01 Select button for more than 2 seconds while switching the X-TOUCH power on Follow the instruction steps 4 to 8 in the section “DIRECT ETHERNET CONNECTION BETWEEN X AIR MIXER...
- Page 5 BEATS” can be used to toggle the console surface between both, Mixer and DAW control. NOTE: X AIR Mixer MIDI rx/tx ags must be o , when X-TOUCH controls the mixer via MIDI KEY: In the information below,* refers to the X18/XR18 only, and ** refers to XR12/XR16 only...
- Page 6 Mute Groups 1...4 TICKS indicates active Auto Mixing Groups X and Y LED: SMPTE indicates XCTL surface LED: BEATS indicates DAW control surface ¹) in combined Xctl-MC or Xctl-HUI modes only, use button to toggle music-group.com behringer.com...
- Page 7 4: Gain2 3: Freq1 4: — EQ (Bus) 5: Gain3 — 4: Freq2 — 5: — page 1/2 6: Gain4 5: Freq3 6: — 7: Gain5 6: Freq4 7: — 8: Gain6 7: Freq5 8: — 8: Freq6 music-group.com behringer.com...
- Page 8 5: Mute Grp 1 page 3/3 5: — 6: DCA Grp 2 6: Mute Grp 2 6: — 7: DCA Grp 3 7: Mute Grp 3 7: — 8: DCA Grp 4 8: Mute Grp 4 8: — music-group.com behringer.com...
- Page 9 Selects the next audio le in the list stopped while SKIP DOWN — Selects the previous audio le in the list stopped Toggles “Play Folder” option that continues TRANSPORT: “REPLACE” red LED playback for all les in the current folder music-group.com behringer.com...
- Page 10 MODE: XCTL + MCU and XCTL + HUI This section shows the operation of the X-TOUCH controls in XCTL + MCU mode and XCTL + HUI mode X-TOUCH rmware: 1.15 X AIR min rmware: 1.12 Operating Modes: Display Network MIDI...
- Page 11 Song position pointer of DAW TICKS Song position pointer of DAW LED: SMPTE indicates active X AIR Mixer surface LED: BEATS indicates active DAW control surface ¹) in combined Xctl-MC or Xctl-HUI modes only, use button to toggle music-group.com behringer.com...
- Page 12 4: Gain2 3: Freq1 4: — EQ (Bus) 5: Gain3 — 4: Freq2 — 5: — page 1/2 6: Gain4 5: Freq3 6: — 7: Gain5 6: Freq4 7: — 8: Gain6 7: Freq5 8: — 8: Freq6 music-group.com behringer.com...
- Page 13 5: Mute Grp 1 page 3/3 5: — 6: DCA Grp 2 6: Mute Grp 2 6: — 7: DCA Grp 3 7: Mute Grp 3 7: — 8: DCA Grp 4 8: Mute Grp 4 8: — music-group.com behringer.com...
- Page 14 Sets the SPP to the next Locator or Marker stopped while Sets the SPP to the previous Locator SKIP REW — stopped or Marker Toggles “Loop” or “Cycle” playback/recording TRANSPORT: “CYCLE” green LED between left/right locator points on/o music-group.com behringer.com...
- Page 15 behringer.com...