Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Behringer Eurorack MX602A
Summary of Contents for Behringer Eurorack MX602A
- Page 1 User’s Manual Version 1.3 December 2001 www.behringer.com...
-
Page 2: Safety Instructions
The user should not attempt to service the appliance beyond that is described in the Operating Instructions. All other servicing should be referred to qualified service personnel. EURORACK MX602A This symbol, wherever it appears, alerts you to important operating and mainte- nance instructions in the accompanying literature. - Page 3 Our daily objective is to be focused on you, the Sound Engineer, and with that focus in mind, it drives us to reach a goal which is unique, and is the backbone of the BEHRINGER philosophy.
- Page 4 Rugged design power supply ensures superior transient response State-of-the-art 4580 IC’s and highest quality components ensure crystal-clear audio performance and ultra-low noise performance Extremely rugged construction ensures long life even under the most demanding conditions Manufactured under the ISO9000 certified management system EURORACK MX602A ®...
-
Page 5: Table Of Contents
7.3 Auditioning a signal and setting up a channel ... 11 7.4 Desk normalization ... 12 7.5 Recording levels ... 12 8. APPENDIX ... 13 8.1 Specifications ... 13 8.2 Front & back views... 14 8.3 Block diagram ... 15 9. WARRANTY ... 16 EURORACK MX602A... -
Page 6: Introduction
MIDI instruments etc. In addition, a stereo tape input is provided, which may also be routed to the main mix, giving the MX602A a total of 10 possible inputs during mixing. Channels 1 and 2 on the MX602A have overload LEDs, while the main mix output has 4-segment bargraph meters. -
Page 7: Mono Input Channel
There is no Solo or PFL function on the MX602A. To accurately set input follow the procedures given in section 7: “Setting Up”. However, if the PEAK LED does not light the input gain cannot be too high. If a reasonable input level is selected, auditioning a single signal should result in a reading of around 0 dB on the main mix meters , provided that both channel and output level controls are set to unity gain (0 dB). -
Page 8: Equalizer
5.2 Stereo line input Aux return Your EURORACK MX602A is equipped with a stereo aux return . If only the left socket has a jack connected, the aux return operates in mono and is permanently assigned to the main mix. The AUX RET. control determines the level of the aux return signal. -
Page 9: 2-Track Input / Main Mix Output
EURORACK MX602A 5.4 2-track input / main mix output Input A 2-track input, on RCA phono jacks , provides easy connection to DAT and other professional and semi- professional audio equipment. The 2-track input is primarily for auditioning mix playback from tape. Switch “2TK TO CTRL ROOM”... - Page 10 1/4" jack plugs Tip = Signal Sleeve = Ground / Shield Sleeve Strain relief clamp Input EURORACK MX602A Cable Shield (+) Signal + Hum (-) Signal + Hum RFI and Hum Balanced use of stereo 1/4" jack plugs Tip =...
-
Page 11: Setting Up
EURORACK MX602A 7. SETTING UP 7.1 Selecting inputs 1) Mono channels accept mic or line inputs. If you are using the mic input, make sure nothing is connected to the line input (and vice-versa). The mic inputs are more sensitive than the line inputs. Do not connect mics with phantom power switched on. -
Page 12: Desk Normalization
5 or 10 dB, and never exceed that level. Engage “peak hold” on your recorder before recording if you want to confirm that you haven’t. Peak meters read more-or-less independent of frequency. Aim for 0 dB recording level for all signals. EURORACK MX602A until transient peaks are regularly hitting +6 dB. Continuous 7. SETTING UP... -
Page 13: Appendix
Shipping weight BEHRINGER is constantly striving to maintain the highest professional standards. As a result of these efforts, modifications may be made from time to time to existing products without prior notice. Specifications and appearance may differ from those listed or shown. -
Page 14: Front & Back Overview
EURORACK MX602A 8.2 Front & back views 8. APPENDIX... -
Page 15: Block Diagram
EURORACK MX602A 8.3 Block diagram 8. APPENDIX... -
Page 16: Warranty
5. Any repair or opening of the unit carried out by unauthorized personnel (user included) will void the warranty. 6. If an inspection of the product by BEHRINGER shows that the defect in question is not covered by the warranty, the inspection costs are payable by the customer.