Related Manuals for THOMSON Grass Valley Triton
Summary of Contents for THOMSON Grass Valley Triton
- Page 1 TRITON routing switcher Single-Bus Control Panel 16x1 Product model no. TTN-CP-1601 INSTALLATION MANUAL MANUAL PART NO. 04-049758-002 Rev. 2 MARCH 07, 2003 the most watched worldwide...
- Page 2 FRANCE Nevada City, CA 95959-7900 Copyright 2003 Thomson Broadcast and Media Solutions, Inc. All rights reserved. Grass Valley, Jupiter, and Triton are trademarks of Thomson. Specifications subject to change without notice. For customer service, please call (800) 547-8949. For comments or questions concerning this manual, please contact: Technical Publications Department, P.O.
-
Page 3: Table Of Contents
Contents Electromagnetic Radiation Notice Hardware Warranty and Software License Parts and Service Revision history General Front panel drawing Connection drawing Power connection Connecting the CP-1601 to your PC Selection of router level Pin-out of RS-232 connector Maximum cable length NCB connection Control bus structure Maximum distance between NCB devices Several routers in one system... -
Page 4: Electromagnetic Radiation Notice
88 - 216 216 - 1000 The policy of Thomson is one of continual development and improvement. For that reason Thomson uses components and manufacturing techniques that provide the current state-of-the-art suppression of electromagnetic radiation. This equipment, in production before October 1, 1981, has not been tested to the above listed measurements. However, equipment such as this delivered after October 1, 1983 will have the measurements on record at the factory. -
Page 5: Hardware Warranty And Software License
Please contact your local Thomson representative for hardware warranty and software license information. Parts and Service Thomson maintains a full stock of replacement parts available for immediate shipment. NORTH AMERICA PARTS AND SERVICE Please call toll-free 1-800-547-8949. You will be switched automatically to the parts and service representative nearest you. -
Page 6: Revision History
Revision history Current revision of this document is the uppermost in the table below. Revision Replaces Date Change Description 06/03/03 Updated with new Thomson/GVG design. 30/01/01 Corrected error in baud rate setting 10/10/00 Initial Revision... -
Page 7: General
CP-1601 Rev. 2 1 General The CP-1601 is a single-bus remote control panel for the Triton series routing switchers. The panel offers input select buttons on the top row. The input buttons have different colors for displaying both video and audio status during breakaway operations. -
Page 8: Power Connection
CP-1601 can also be delivered with DC ±5V / 30W, which may be fed by a 36 – 72 VDC mains power source. A Frame mounted power supply solution is also available. Please refer to the latest Triton Product Catalogue for power supply types, or call Thomson Grass Valley for this information. -
Page 9: Connecting The Cp-1601 To Your Pc
CP-1601 Rev. 2 3 Connecting the CP-1601 to your PC For connection to a PC with Triton Router Control System, the RS-232 interface is used. The RS-232 port on all Triton devices uses the standard DCE pin-out, see pin-out table under 4.3. A standard modem cable can be used for connecting the panel to the PCs serial port. -
Page 10: Ncb Connection
CP-1601 Rev. 2 4 NCB connection Via the Network Control Bus system several routers and control panels can be interconnected. CP-1601 utilises MIDI and/or RJ-45 connectors for connecting to the NCB. Up to 16 levels of routers, or combinations of routers, can be controlled from the Triton - Router Control System. -
Page 11: Pin-Out And Cable Type
CP-1601 Rev. 2 Pin-out and cable type 4.5.1 RJ45 connectors On some Triton devices, the NCB cable can be connected to RJ-45 connectors. The following pin-out is used: Pin 1 = Not Connected Pin 2 = Not Connected Pin 3 = Not Connected Pin 4 = data Pin 5 = data Pin 6 = Not Connected... -
Page 12: Rj45 To 5-Pin Din Converter
CP-1601 Rev. 2 4.5.3 RJ45 to 5-pin DIN converter In configurations that include both devices with RJ45 connectors, and devices with 5-pin DIN connectors, an RJ45 to 5-pin DIN converter may be used to complete the control loop. This converter holds both connector types, and may work both ways, thus from RJ45 to 5-pin DIN, as well as from 5-pin DIN to RJ45. - Page 13 CP-1601 Rev. 2 Triton - RCS Complete the Control loop, by connecting all Control bus connections to all Triton devices, before • powering up any Triton device.
-
Page 14: Control Panel Configuration
CP-1601 Rev. 2 5 Control panel configuration Panel level The second Dip-switch Block from the left, SW2 (8 user switches): Switch 1 – 3 (from left) on the configuration switch set the control panels level for communication with the other units in the NCB system. The panels on the NCB dedicated to operate with a specific router have to be configured to the same level. -
Page 15: Configuring Output
CP-1601 Rev. 2 Configuring output The third Dip-switch Block from the left, SW1 (8 user switches): Switches 1 – 3 are not in use for this product. Switches 4 - 8 on the configuration switch define the router output for the control panel. The outputs can be switched according to the following pattern: means switch OFF (down) means switch ON (up) -
Page 16: Programming Of Restrictions
CP-1601 Rev. 2 Programming of restrictions If the Restrictions option is enabled by the user, the previously programmed restrictions will be fetched from the on-board memory during power-up. New restrictions may be programmed by putting the panel in “Programming mode”. This is done, starting from Panel Disable state, by pushing and holding “V/A toggle”, “Take On/Off”... -
Page 17: Operating The Cp-1601
CP-1601 Rev. 2 6 Operating the CP-1601 PANEL ENABLE button After powering-up the control panel will be disabled. Press the PANEL ENABLE button to start operating. If you want to lock the control panel after use you simply disable by operating the PANEL ENABLE button once again.