Siemens PROFIBUS PA SIPART PS2 Manual page 156

Scope of delivery
OrderNumber = "6DR410* / 6DR55**"
Info_Text = "Electropneumatic positioner, PROFIBUS PA Profile 3.0"
Freeze_Mode_supp = 0
Sync_Mode_supp = 0
Auto_Baud_supp = 0
Set_Slave_Add_supp = 1
Min_Slave_Intervall = 200
Modular_Station = 1
Max_Module = 1
Max_Input_Len = 15
Max_Output_Len = 10
Max_Data_Len = 25
Max_Diag_Data_Len = 14
Fail_Safe = 0
Max_User_Prm_Data_Len
Ext_User_Prm_Data_Const(0)
Ext_User_Prm_Data_Const(1)
Ext_User_Prm_Data_Const(2)
;----------- Description of extended DP features: ---------------------
;
DPV1_Slave
C2_Read_Write_supp
C2_Max_Data_Len
C2_Read_Write_required
C2_Max_Count_Channels
Max_Initiate_PDU_Len
C2_Response_Timeout
DPV1_Data_Types
;----------- Description of physical interface for synchronous transmission:
; IEC61158-2
Physical_Interface
Transmission_Delay_31.25
Reaction_Delay_31.25
End_Physical_Interface
;----------- Description of device related diagnosis: ---------------------
;
Unit_Diag_Bit(16) = "Status appears"
Unit_Diag_Bit(17) = "Status disappears"
Unit_Diag_Bit(24) = "Hardware failure electronics"
Unit_Diag_Bit(25) = "Hardware failure mechanics"
Unit_Diag_Bit(26) = "Motor temperature too high"
Unit_Diag_Bit(27) = "Electronic temperature too high"
Unit_Diag_Bit(28) = "Memory error"
Unit_Diag_Bit(29) = "Measurement failure"
Unit_Diag_Bit(30) = "Device not initialised"
Unit_Diag_Bit(31) = "Device initialisation failed"
Unit_Diag_Bit(32) = "Zero point error"
Unit_Diag_Bit(33) = "Power supply failed"
Unit_Diag_Bit(34) = "Configuration invalid"
Unit_Diag_Bit(35) = "Restart"
Unit_Diag_Bit(36) = "Coldstart"
Unit_Diag_Bit(37) = "Maintenance required"
Unit_Diag_Bit(38) = "Characteristics invalid"
Unit_Diag_Bit(39) = "Ident_Number violation"
Unit_Diag_Bit(55) = "Extension available"
;------------------------------------------------------------------------------
;---------- Module Description -----------------------------------------
;Variables combination for Analog Output
;Abbreviations
; RB = READBACK, CB = CHECKBACK, RC_OUT = RCAS_OUT, RC_IN = RCAS_IN
;Identifier Bytes
Module = "SP"
0 ; Module-Reference
154
; 0 = no Freeze Mode supported
; 0 = no Sync Mode supported
; 1 = Set Slave AddrFunction supported
; 20ms min. betw. 2 slave list cycles
; 1 = Modular Station
; 1: PA_AO
; maximum Input Length
; maximum Output Length
; maximum In-Output Length
= 3
= 0x00 ;DPV1 Status 1, DPV1-Enable = 0
= 0x00 ;DPV1 Status 2, no Alarms enabled
= 0x00 ;DPV1 Status 3
= 0
= 1
= 128
= 1
= 4
= 52
= 4000
= 0
= 1
= 0
= 0
0xA4
SIPART PS2 PA Manual
A5E00127926-03