Additional Information - Dyson V11 Absolute User Manual

Additional information

Please read the 'Important safety instructions' in the Dyson User manual before proceeding.
Installing your docking station
• Unpack the docking station, charger and installation leaflet.
• Choose a suitable location for the docking station and make sure there is no
pipework (gas, water or air), electrical cables, wires or ductwork directly behind the
mounting location.
• Don't locate the docking station near a heat source such as a cooker, radiator or in
direct sunlight.
• Follow the instructions on the installation leaflet.
• Click the tools into place on the docking station.
• Place the machine into the docking station.
• Plug the charger into the mains electricity supply. Switch on (if necessary) to charge
the battery.
Your machine will need to be fully charged before first use.
The docking station must be mounted in accordance with regulations and applicable codes/
standards (state and local laws may apply).
Dyson recommends the use of protective clothing, eyewear and materials when installing the
docking station.
Using your machine
• Check that the underside of the cleaner head or tool is clean and free from foreign objects
that may cause damage.
• Before vacuuming your flooring, rugs and carpets, check the manufacturer's
recommended cleaning instructions.
• The brush bar on the machine can damage certain carpet types and floors. Some
carpets will fuzz if a rotating brush bar is used when vacuuming. If this happens, we
recommend vacuuming without the motorised floor tool and consulting with your
flooring manufacturer.
Emptying your clear bin
• Empty as soon as the dirt reaches the MAX level – don't overfill. Using the machine when
the dirt is above the MAX line may cause the dirt to reach the filter and more frequent
maintenance will be required.
• Be careful not to pull the power trigger while the clear bin is open for emptying.
• Press the red wand release button and pull the wand away from the bin.
• To release the dirt:
– Hold the machine over a bin in a downwards position.
– Firmly push the red bin release button. The bin will slide down, cleaning the shroud as it
goes and the bin base will open.
The bin base won't open if the red bin release button isn't pushed down all the way.
To minimise dust contact when emptying, encase the clear bin tightly in a dust proof bag and
empty. Remove the clear bin carefully from the bag. Seal the bag tightly and dispose.
Be careful not to pull the power trigger while the clear bin is open for emptying.
• To close the clear bin:
– Push the bin base upwards until the clear bin and bin base click into place.
Cleaning your clear bin
If it is necessary to clean your clear bin, empty the bin as shown in the 'Emptying your clear bin'
section.
• Press the red button located on the bin runner to release the bin and slide the bin off
the runner.
• Clean the clear bin with a damp cloth only.
• Make sure that the clear bin and seals are completely dry before replacing.
• To refit the clear bin:
– Insert the spine on to the bin runner.
– Close the clear bin by pushing the bin base upwards until the clear bin and bin base click
into place.
The clear bin is not dishwasher safe and the use of detergents, polishes or air fresheners to
clean the clear bin is not recommended as this may damage your machine.
Looking for blockages
• Your machine is fitted with an automatic cut-out. If any part becomes blocked, the machine
may automatically cut out.
• The motor will pulse and the LCD screen will indicate that there is a blockage.
• Leave to cool down before looking for blockages.
• Be careful not to pull the power trigger while looking for blockages.
• Make sure any blockages are clear and all parts are refitted before using your machine.
• Beware of sharp objects when checking for blockages.
• Clearing blockages is not covered by your guarantee.
• To check for blockages in the main body of your machine, remove the clear bin following
the instructions in the 'Emptying your clear bin' section and remove any blockage.
• If you can't clear an obstruction from the cleaner head, you may need to remove the brush
bar. Use a coin to unlock the fastener, slide the brush bar out of the cleaner head and
remove the obstruction. Replace the brush bar and securely tighten the fastener. Make sure
it is fixed firmly before using your machine.
• Your machine has carbon fibre brushes. Take care if coming into contact with them, as they
may cause minor skin irritation. Wash your hands after handling the brushes.
12
Washing your filter unit
To always get the best performance from your machine, it is important to regularly clean the
filters and check for blockages.
The LCD display will alert you when the filter unit needs washing. We recommend that you
wash your filter at least once a month or when your machine alerts you.
• Remove the filter unit by twisting it anti clockwise. Gently pull away from the machine.
• Tap the filter unit gently, to remove any excess dust and debris before washing it.
• Wash the filter unit in cold water only.
• Wash the pleated paper element of the filter unit first; hold the filter unit under a cold water
tap with the foam element downwards and run cold water over the pleated paper.
• Wash the foam element of the filter unit next; hold the filter unit under a cold water tap with
the foam element downwards so that dirty water does not contaminate the pleated paper
element. Run cold water over the inside and outside of the foam element and squeeze the
foam gently to expel the dirt.
• Repeat washing both parts of the filter unit until the water runs clear.
• Gently shake the filter unit to remove any excess water and leave to drain with the foam
element end facing up.
• Leave the filter unit to dry completely in a dry environment with good airflow, for a
minimum of 24 hours.
• Check that the filter unit is completely dry.
• To refit, position the filter unit in place on the main body and twist clockwise until it clicks
into place.
The filter unit may require more frequent washing if vacuuming fine dust or if use is mainly in
Boost mode.
Don't put any part of your machine in a dishwasher, washing machine, tumble dryer, oven,
microwave or near a naked flame.
Looking after your Soft roller cleaner head
• Turn the cleaner head upside down. Use a coin to turn the end cap a quarter anticlockwise
until it clicks into the unlocked position.
• Rotate the end cap to the open position. Gently slide the main brush bar out of the
cleaner head.
• Remove the end cap from the main brush bar.
• Do not wash the end cap.
• Lift the small brush bar out of the cleaner head.
• Hold the brush bars under running water and gently rub to remove any lint or dirt.
• Stand the brush bars upright as shown. Leave to dry completely for a minimum of 24 hours.
• Before replacing, check that the brush bars are completely dry.
• Put the small brush bar back into position making sure it clicks into place.
• Reattach the end cap to the main brush bar.
• Slide the main brush bar into the cleaner head. Rotate the end cap to the closed position.
• Close the fastener by turning it a quarter clockwise. Check that the fastener and brush bars
are all securely in place.
Charging and storing
• This machine will switch off if the battery temperature is below 10°C (50°F). This is
designed to protect the motor and battery. Do not charge the machine and then move it to
an area with a temperature below 10°C (50°F) for storage purposes.
• To help prolong battery life, avoid recharging immediately after a full discharge. Allow to
cool for a few minutes.
• Avoid using the machine with the battery flush to a surface. This will help it run cooler and
prolong battery run time and life.
Battery safety instructions
• If the battery needs replacing, please contact the Dyson Helpline.
• Use only the Dyson charger Part Number 217160 or 270576 for charging this
Dyson machine.
• Use only the Dyson battery Part Number 355983 for this Dyson machine. Other types of
batteries may explode, resulting in fire and causing injury to persons and damage.
CAUTION
The battery used in this machine may present a risk of fire or chemical burn if mistreated. Do
not short contacts, heat above 60°C (140°F), or incinerate. Keep away from children. Do not
disassemble and do not dispose of in fire.
Disposal information
• Dyson products are made from high grade recyclable materials. Recycle where possible.
• The battery should be removed from the machine before disposal.
• Dispose of or recycle the battery in accordance with local ordinances or regulations.
• Dispose of the exhausted filter unit in accordance with local ordinances or regulations.
Dyson customer care
Thank you for choosing to buy a Dyson machine
After registering your two-year guarantee, your Dyson machine will be covered for parts
and labour (excluding filters) for two years from the date of purchase, subject to the terms of
the guarantee. However, indispensable legal rights of the final consumer under applicable
national legislation governing the sale of consumer goods are not affected by the terms of
the guarantee. If you have any queries regarding your Dyson machine, visit www.dyson.com/
support for online help, general tips and useful information about Dyson.
Alternatively, you can call the Dyson Helpline with your serial number and details of where
and when you bought the machine.
If your Dyson machine needs a repair, call the Dyson Helpline so we can discuss the available
options. If your Dyson machine is under guarantee, and the repair is covered, it will be
repaired at no cost.
Limited 2-year guarantee
Terms and conditions of the Dyson 2-year limited guarantee
What is covered
• The repair or replacement of your Dyson machine (at Dyson's discretion) if it is found to be
defective due to faulty materials, workmanship or function within two years of purchase or
delivery (if any part is no longer available or out of manufacture, Dyson will replace it with
a functional replacement part).
• This guarantee will only be valid if the machine is used in the country in which it was sold.