Related Manuals for Behringer X-ADAT
Summary of Contents for Behringer X-ADAT
- Page 1 Quick Start Guide DIGITAL MIXER OPTION X-ADAT High-Performance 32-Channel ADAT / Wordclock Expansion Card for X32...
- Page 2 DIGITAL MIXER OPTION X-ADAT Table of Contents Important Safety Instructions ......3 FCC INFORMATION U.S.A.......10 English 1. Introduction ..........11 2. Installation ..........11 3. Connector Plate ..........12 4. Connection Scenarios ........12 5. X32 Setup ............13 Español 1. Introducción ..........14 2. Instalación ..........14 3.
- Page 3 Quick Start Guide Caution cart is used, use caution when moving Important Safety the cart/apparatus combination to Instructions These service instructions avoid injury from tip-over. are for use by qualifi ed 13. Unplug this apparatus during service personnel only. To reduce lightning storms or when unused for the risk of electric shock do not long periods of time.
- Page 4 DIGITAL MIXER OPTION X-ADAT 6. Limpie este aparato con un LEGAL DISCLAIMER Este símbolo, siempre que paño seco. aparece, le advierte de la MUSIC Group accepts no liability for presencia de voltaje 7. No bloquee las aberturas any loss which may be suff ered by peligroso sin aislar dentro de la caja;...
- Page 5 MIDAS, KLARK TEKNIK, la conexión disponga de una unión Pour éviter tout risque TURBOSOUND, BEHRINGER, BUGERA y a tierra. de choc électrique, DDA son marcas comerciales o marcas ne pas ouvrir le capot de l’appareil 16.
- Page 6 Before installing the card, you must refer to the owner’ s BEHRINGER may void your authority, granted by the FCC, manual of the host device or to behringer.com to verify that to use the product. your host device supports this card, and to verify the number 2.
- Page 7 ADAT connectivity. 2. Installation Before you install the X-ADAT card in the expansion slot of the X32 console, you must check behringer.com to verify whether the console firmware supports that card. Caution – before installing the X-ADAT card into the console, you must make sure that the console’s power switch is turned off.
- Page 8 • 3x small counter sunk screws fixing the bracket on the pcb. 8 channels per connector Do not loosen these! 4. Connection Scenarios X-ADAT ➝ external hard disc recorder (providing Word Clock via BNC coaxial connection) Coaxial VIEW VIEW VIEW...
- Page 9 • local clock indicates the X32 console’s internal clock. X-ADAT card can be selected as the clock source on the X32 Setup/ config page. In this case, the X32 will be slaved to the ADAT clock received on BNC input or fiber optic Toslink inputs. Note that this may require the console to be rebooted if the internal and external clock rates are different (i.e.
- Page 10 DIGITAL MIXER OPTION X-ADAT Specifications Connectors TOSLINK opt. IN TOSLINK opt. OUT WORDCLOCK BNC IN/OUT Input/Output Characteristics Sample rates 44.1 kHz / 48 kHz Sample word length 24 Bit Clock synchronization selectable internal/Local WordClock In ADAT In 1 ADAT In 2...
- Page 11 Quick Start Guide FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION DIGITAL MIXER OPTION X-ADAT MUSIC Group Services NV Inc. Responsible Party Name: Address: 5270 Procyon Street Las Vegas, NV 89118 +1 702 800 8290 Phone Number: DIGITAL MIXER OPTION X-ADAT complies with the FCC rules as mentioned in the following paragraph: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
- Page 12 We Hear You...