Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Strongway 61132
Summary of Contents for Strongway 61132
- Page 1 3000-Lb. Vehicle Positioning Jacks Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. Item #61132 READ & SAVE THESE INSTRUCTIONS...
- Page 2 Thank you very much for choosing a Strongway™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it.
-
Page 3: Table Of Contents
Table of Contents Intended Use ............................4 Technical Specifications ........................4 Important Safety Information ....................... 4 Specific Operation Warnings ....................... 5 Operating Instructions .......................... 6 Maintenance ............................9 Troubleshooting ............................ 9 Parts Diagram ............................10 Parts List .............................. 11 Replacement Parts ..........................12 Limited Warranty .......................... -
Page 4: Intended Use
Intended Use The Strongway 3000-Lb. Vehicle Positioning Jack set maneuvers vehicles in any direction on 4 strong casters. Using two jacks permits a full 180° vehicle pivot; using 4 jacks places the vehicle on a 360° rolling platform. Technical Specifications... -
Page 5: Specific Operation Warnings
Keep children and bystanders away from the work area while operating the tool. Do not allow children to handle the product. Be aware of all power lines, electrical circuits, water pipes, and other mechanical hazards in your work area. Some of these hazards may be hidden from your view and may cause personal injury and/or property damage if contacted. -
Page 6: Operating Instructions
Use only on a hard, level surface. Before moving, lower the load to the lowest possible point. Apply load as close to the vertical portion of the lifting member as possible. Before moving the load, assure that the load is centered and secured with a load restraint device. ... - Page 7 2. Pull the lock pin out from the frame. 3. Before operation, open the release valve by turning the hand-wheel counter-clockwise. Expand the jack with the hand-wheel to place the rollers around the tire; position the jack so both rollers are in contact with the tire tread.
- Page 8 4. Install the jack so that the unit is parallel to the sidewall of the tire to be lifted. Leave approximately 3/4" of clearance between tire and jack. This is very important: If the unit is misaligned, the tire may hit the axle of the jack and not the rollers.
-
Page 9: Maintenance
Maintenance Maintain the jack set by adopting a program of conscientious repair and maintenance in accordance with the following recommended procedures. It is recommended that the general condition of any tool be examined before it is used. Keep your tool in good repair. Keep handles dry, clean, and free from oil and grease. -
Page 10: Parts Diagram
Parts Diagram Page 10 of 14... -
Page 11: Parts List
Parts List Part Number Part Description Quantity Ram assembly Bolt M16x15 Flat washer Ø16 Nut M16 Roller raceway Roller Raceway lock screw Lock nut M12 4” Swivel castor Left frame Lock pin with chain Screw M6x20 Lock washer Ø6 Flat washer Ø6 Right frame Hook Washer for hook... -
Page 12: Replacement Parts
Part Number Part Description Quantity Safety valve screw O-ring Screw Replacement Parts For replacement parts and technical questions, please call Customer Service at 1-800-222-5381. Not all product components are available for replacement. The illustrations provided are a convenient reference to the location and position of parts in the assembly sequence. ... -
Page 13: Limited Warranty
Northern Tool and Equipment Company, Inc. ("We'' or "Us'') warrants to the original purchaser only ("You'' or "Your") that the Strongway product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. - Page 14 Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.com Made in China Page 14 of 14...