Related Manuals for Ricoh M047 Series
Summary of Contents for Ricoh M047 Series
- Page 1 M047 Series Training - Kriss-P2 /Model Kr-P2 M047 Series Training Model Kr-P2 Product Outline Slide 1...
- Page 2 M047 Series Training - Kriss-P2 /Model Kr-P2 The Machine Slide 2...
- Page 3 M047 Series Training - Kriss-P2 /Model Kr-P2 Operation Panel The Machine Exhaust Vent (Exterior - Front) Bypass Tray Bypass Tray Extension Intake Vent Paper Size Dial Front Cover Release Button Power Switch Paper tray (500 sheets) Slide 3...
- Page 4 M047 Series Training - Kriss-P2 /Model Kr-P2 The Machine (Exterior - Rear) Optional SD Card Interface Slots Board Slot Rear Cover Power Connector Paper Tray Ethernet Cover USB-B USB-A Intake Vent Controller Board Slide 4...
- Page 5 M047 Series Training - Kriss-P2 /Model Kr-P2 The Machine (Interior - Front) Registration Roller Transfer Roller Print Cartridge Front Cover Slide 5...
- Page 6 M047 Series Training - Kriss-P2 /Model Kr-P2 Machine (Interior - Rear) Envelope Lever Fusing Unit Lock Levers Slide 6...
- Page 7 M047 Series Training - Kriss-P2 /Model Kr-P2 Product Lineage & Changes ! Predecessor Model: Model K-P4 ! Current Model: Model Kr-P2 ! New to Model Kr-P2 (relative to Model K-P4) " Controller board " Engine board " Firmware " Power supply unit "...
-
Page 8: Operation Panel
M047 Series Training - Kriss-P2 /Model Kr-P2 Operation Panel Slide 8... - Page 9 M047 Series Training - Kriss-P2 /Model Kr-P2 Options ! Paper Feed Unit PB3090 ! IEEE 1284 Interface Board Type A ! Duplex Unit Type AD610 ! Data Overwrite Security Unit ! Envelope Feeder Type 610 Type L ! Hard Disk Drive Type 2670...
- Page 10 M047 Series Training - Kriss-P2 /Model Kr-P2 M047 Series Training Model Kr-P2 Specifications Slide 10...
-
Page 11: Specifications
M047 Series Training - Kriss-P2 /Model Kr-P2 Specifications - 1/5 ! Weight " 22.5 Kg. (49.6 lb.) » including paper tray & print cartridge ! Dimensions " Excluding standard tray » 478 x 410 x 404 (mm) » 18.8 x 16.1 x 15.9 (inch) "... - Page 12 M047 Series Training - Kriss-P2 /Model Kr-P2 Specifications - 2/5 ! Print Resolution " 300/600/1200 dpi ! Continuous Print Speed " LEF A4 mono » 35 ppm " LT mono » 35 ppm ! Duplex Print Speed " 32 ppm from standard tray "...
- Page 13 M047 Series Training - Kriss-P2 /Model Kr-P2 Specifications - 3/5 ! Copy Paper Weight " Paper tray » 60-216 g/m (16-57 lb.) " Bypass tray » 52-216 g/m (14-57 lb.) " Optional PFU » 60-216 g/m (16-57 lb.) " Duplex »...
- Page 14 M047 Series Training - Kriss-P2 /Model Kr-P2 Specifications - 4/5 ! Paper Input Capacity " Standard tray & optional paper trays » 500 sheets (80 g/m / 20 lb.) " By-pass tray » 100 sheets (80 g/m / 20 lb.) "...
- Page 15 M047 Series Training - Kriss-P2 /Model Kr-P2 Specifications - 5/5 ! Environmental Standard " Energy Star Tier 2 or Ver. 1.1 ! Power Consumption " Maximum » Main unit, including NIB – 910 W or less (EU) – 870 W or less (NA) »...
- Page 16 M047 Series Training - Kriss-P2 /Model Kr-P2 Controller Board Specifications - 1/3 ! CPU " RM7035 » 466 MHz ! Printer Languages " Standard » PCL5e/ XL, IRIPS PS3/ PDF, RPCS " Option » IPDS ! Resolution " RPCS » 600/1200 dpi "...
- Page 17 M047 Series Training - Kriss-P2 /Model Kr-P2 Controller Board Specifications - 2/3 ! RAM " Resident: 256 MB " Optional: 256 MB » Total possible RAM memory: 512 MB ! Flash ROM " NAND: 128 MB " NOR: 4 MB ! HDD "...
- Page 18 M047 Series Training - Kriss-P2 /Model Kr-P2 Controller Board Specifications - 3/3 ! Firmware Update " SD card » One SD card holds all programs " RFU (Remote Firmware Update) ! Network Protocol " TCP/IP (including IPP) " IPX/SPX " SMBI "...
- Page 19 M047 Series Training - Kriss-P2 /Model Kr-P2 M047 Series Training Model Kr-P2 Installation Slide 19...
-
Page 20: Installation Requirements
M047 Series Training - Kriss-P2 /Model Kr-P2 Installation Requirements ! Environment " Temperature range » 10ºC to 32ºC (50ºF to 89.6ºF) " Humidity range » 15% to 89% RH " Ambient Illumination » Less than 2,000 lux – Do not expose to direct sunlight "... -
Page 21: Machine Space Requirements
M047 Series Training - Kriss-P2 /Model Kr-P2 Machine Space Requirements 10cm / 4 inches 10cm / 4 inches 10cm / 4 inches 10cm / 4 inches ! Place machine near power source, with above clearances. Slide 21... -
Page 22: Attaching Paper Feed Unit
M047 Series Training - Kriss-P2 /Model Kr-P2 Attaching Paper Feed Unit ! Remove all shipping tape. ! Carry properly. ! Lower machine straight down onto paper tray. " Carefully align guide pins. Slide 22... -
Page 23: Hard Disk Drive Installation
M047 Series Training - Kriss-P2 /Model Kr-P2 Hard Disk Drive Installation Set HDD as shown Carefully align Tighten screws Slide 23... - Page 24 M047 Series Training - Kriss-P2 /Model Kr-P2 Installing SDRAM Module ! Slide the Controller Board out. ! Verify that the slot for the SDRAM Module (board) is empty. " Standard memory - 256MB " Optional memory: » +128MB or +256MB »...
-
Page 25: Wireless Lan Installation
M047 Series Training - Kriss-P2 /Model Kr-P2 Wireless LAN Installation ! Remove Slot Cover (two screws). ! Slide Wireless LAN Interface Unit into slot. ! Tighten two attachment screws. Slide 25... - Page 26 M047 Series Training - Kriss-P2 /Model Kr-P2 Gigabit Ethernet Board Installation ! Remove slot cover. ! Slide Gigabit Ethernet Board into the slot. ! Secure Gigabit Ethernet Board to Controller Board with two screws. ! Follow same procedures when installing IEEE 1284 Interface Board.
-
Page 27: Duplex Unit Installation
M047 Series Training - Kriss-P2 /Model Kr-P2 Duplex Unit Installation Remove rear cover Open rear cover Slide Duplex Unit along rails Push Duplex Unit securely into printer Slide 27... - Page 28 M047 Series Training - Kriss-P2 /Model Kr-P2 M047 Series Training Model Kr-P2 Machine Component Overview Slide 28...
- Page 29 M047 Series Training - Kriss-P2 /Model Kr-P2 LED Speed Indications ! Orange illumination indicates 100BASE-TX operation. Standard ! Green illumination indicates Ethernet Port 10BASE-T operation. ! Green illumination indicates 10BASE-T operation. Gigabit ! Both green and orange illumination Ethernet Port indicates 1000BASE-T operation.
- Page 30 M047 Series Training - Kriss-P2 /Model Kr-P2 Paper Tray Extension ! To extend tray for long paper sizes, first release two locks. ! After extending tray, relock both locks. Slide 30...
- Page 31 M047 Series Training - Kriss-P2 /Model Kr-P2 Adjustable Paper Lift Normal Thick Position Position Thick Paper " Slide green switches to rear, which frees spring pressure, increasing tray lift force. Normal Paper " Keep green switches forward, holding down extra springs and relying on normal light spring pressure.
-
Page 32: Paper Path
M047 Series Training - Kriss-P2 /Model Kr-P2 Paper Path Slide 32... -
Page 33: Drive Layout
M047 Series Training - Kriss-P2 /Model Kr-P2 Drive Layout Main Motor Registration Clutch Relay Clutch Bypass Feed Solenoid Paper Feed Clutch Slide 33... -
Page 34: Paper Size Detection
M047 Series Training - Kriss-P2 /Model Kr-P2 Paper Size Detection ! Manually set Paper Paper Size Switch Size Dial for correct paper size in drawer. ! Set "*" for wider range of paper sizes " Set via Paper Input Menu. -
Page 35: Remaining Paper Detection
M047 Series Training - Kriss-P2 /Model Kr-P2 Remaining Paper Detection ! Remaining paper detected by combination of Remaining Paper Remaining Sensor signals. Paper Sensor-2 Remaining ! Signals from Paper Sensor-1 these sensors indicates whether there are 500, 450, 250, or 50 sheets remaining. -
Page 36: Bypass Tray
M047 Series Training - Kriss-P2 /Model Kr-P2 Bypass Tray Bypass Paper Sensor Paper Bypass Relay Roller Feed Roller Bypass Feed Roller Shaft Cams Bypass Feed Roller Bypass Feed Roller Gear Registration Roller Bypass Feed Solenoid Bypass paper sensor detects paper on tray. - Page 37 M047 Series Training - Kriss-P2 /Model Kr-P2 Controller 2 2 2 2 ..5 5 5 5 inch S CPUCLK CPUCLK CPUCLK CPUCLK( ( ( ( 133 133MHz MHz) ) ) ) inch S inch S- - - - ATA...
-
Page 38: Controller Board
M047 Series Training - Kriss-P2 /Model Kr-P2 Controller Board - 2/2 ! The controller controls all applications. Optional features can be added by inserting application(s) on an SD card into the controller SD slot. " ASIC » The ASIC controls all functions of printer controller board. -
Page 39: Printing Process
M047 Series Training - Kriss-P2 /Model Kr-P2 Printing Process Quenching Drum Charge Development Cleaning Laser Exposure Separation Image Transfer Slide 39... -
Page 40: Transfer Roller
M047 Series Training - Kriss-P2 /Model Kr-P2 Transfer Roller ! Transfer roller is removed from front door. " Do not touch transfer roller surface. » See service manual Slide 40... -
Page 41: Toner End Sensor
M047 Series Training - Kriss-P2 /Model Kr-P2 Toner End Sensor ! To access Toner End Sensor, first: " Open front door " Remove print cartridge Toner End Sensor Slide 41... -
Page 42: Electrical Components
M047 Series Training - Kriss-P2 /Model Kr-P2 Electrical Components ! See following slides and service manual for details on the following: " Printer Controller Board " Engine Board " Main Motor " Relay Clutch " Paper Feed Clutch " Registration Clutch "... - Page 43 M047 Series Training - Kriss-P2 /Model Kr-P2 Electrical Paper Exit Sensor Fusing Exit Sensor Components Polygon Mirror Motor LD Unit Overflow Sensor Bypass Feed Solenoid Synchronization Detector Bypass Paper Set Sensor Slide 43...
-
Page 44: Various Components
M047 Series Training - Kriss-P2 /Model Kr-P2 Various Main Motor Registration Clutch Components Thermistor Relay Clutch Thermostat Paper Feed Clutch Fusing Pressure Sensor Paper Size Switch Registration Sensor Remaining Paper Sensor - 2 Toner End Sensor Remaining Paper Sensor - 1... -
Page 45: Printer Controller Board
M047 Series Training - Kriss-P2 /Model Kr-P2 Printer Controller Board ! NVRAM Printer " Remove Controller Board NVRAM from old printer controller board and insert on new board. » Remove Duplex Unit before removing controller board. NVRAM Slide 45... -
Page 46: Main Motor
M047 Series Training - Kriss-P2 /Model Kr-P2 Main Motor Main Motor Slide 46... -
Page 47: Changing Paper Size
M047 Series Training - Kriss-P2 /Model Kr-P2 Changing Paper Size Paper Size Dial ! Adjust paper size dial for size and feed direction of paper. Slide 47... -
Page 48: Paper End Detection
M047 Series Training - Kriss-P2 /Model Kr-P2 Paper End Detection Paper End Sensor ! When there is no paper in tray... " Feeler falls into cutout in bottom plate, and paper end sensor comes on. Feeler Slide 48... - Page 49 M047 Series Training - Kriss-P2 /Model Kr-P2 Paper Tray Spring Pressure ! When loading paper into tray, in addition to usual steps: " Set green switch to match thickness of paper. » Two springs under paper tray plate provide extra lifting power when using heavy (thick) paper.
- Page 50 M047 Series Training - Kriss-P2 /Model Kr-P2 Paper Path Path from main Paper Tray Path from Bypass Tray Note: If both optional paper tray units are installed, the envelope feeder must go in the top tray. Optional Paper Tray Unit...
- Page 51 M047 Series Training - Kriss-P2 /Model Kr-P2 Paper path Paper Path from Main Paper Tray Paper path from Bypass Tray Paper path from Main Paper Tray Paper path from Duplex Unit Paper Tray-2 (Option) Paper Tray - 2 Paper path from...
-
Page 52: Machine Configuration
M047 Series Training - Kriss-P2 /Model Kr-P2 Machine Configuration Duplex Unit Main Unit M374 M047 ! If both optional paper trays are installed, then envelope feeder Envelope must go in top tray. Feeder G807 Paper Tray Unit G399 Slide 52... - Page 53 M047 Series Training - Kriss-P2 /Model Kr-P2 Mechanical Component Layout Laser Unit Quenching Lamp Print Cartridge Drum ! See service manual for more details. Slide 53...
- Page 54 M047 Series Training - Kriss-P2 /Model Kr-P2 Drive Layout Main Motor Registration Clutch Relay Clutch Bypass Feed Solenoid Paper Feed Clutch Slide 54...
- Page 55 M047 Series Training - Kriss-P2 /Model Kr-P2 LCD Display PC Boards, etc. Operation Panel Board Rear Cover Switches Controller Board Front Door Switch Thermistor Exhaust Fan (out) Engine Board Quenching Lamp PSU - Power Supply Unit Cooling Fan (in) High Voltage Supply...
-
Page 56: Cooling Fans
M047 Series Training - Kriss-P2 /Model Kr-P2 Cooling Fans ! Better cooling is achieved with Exhaust Fan new Input Cooling Fan, paired with Exhaust Fan. ! Thermistor in front door detects Thermistor temperature inside machine. Cooling Fan Slide 56... - Page 57 M047 Series Training - Kriss-P2 /Model Kr-P2 Optional Interface Boards Memory Board SD Card Wireless Controller Board Gigabit Ethernet ! Only one of the following Optional Interface Optional Interface Boards Boards can be installed at a time: " Wireless LAN...
- Page 58 M047 Series Training - Kriss-P2 /Model Kr-P2 Controller Board Hard Disk Drive Installation Area USB-A USB-B Optional Interface Board Slot Memory Board Slot Slide 58...
-
Page 59: Hard Disk Drive (Hdd)
M047 Series Training - Kriss-P2 /Model Kr-P2 Hard Disk Drive (HDD) HDD - Hard Disk Drive Screws Slide 59... - Page 60 M047 Series Training - Kriss-P2 /Model Kr-P2 Wireless LAN Interface Unit Slide 60...
-
Page 61: Gigabit Ethernet Board
M047 Series Training - Kriss-P2 /Model Kr-P2 Gigabit Ethernet Board Protective Caps Ferrite Core Note: Installing Gigabit Ethernet Board disables Controller Board's built-in Ethernet and USB ports (block with caps when installing Gigabit Ethernet Board). Note: Installing Gigabit Ethernet Board disables Controller Board's built-in Ethernet and USB ports (block with caps after installation of Gigabit Ethernet Board). - Page 62 M047 Series Training - Kriss-P2 /Model Kr-P2 SD Memory Card Options Data Overwrite Security Unit Remove reattach cover when installing SD card(s) VM Card Slide 62 Always install SD card cover on machine – both when the slots are empty and when a card is installed.
- Page 63 M047 Series Training - Kriss-P2 /Model Kr-P2 M047 Series Training Model Kr-P2 Maintenance Slide 63...
-
Page 64: User Maintenance
M047 Series Training - Kriss-P2 /Model Kr-P2 User Maintenance ! With Maintenance Kit, all PM items can be performed by customer. " Meter-change mode must be set to "disabled" » Engine SP mode 5930 " Operation panel shows "Replace Maintenance Kit"... -
Page 65: Service Maintenance
M047 Series Training - Kriss-P2 /Model Kr-P2 Service Maintenance ! To enable machine for maintenance by service technician, meter-charge mode must be set to: " "1: Yes" with SP5930-001. ! Note: See table in service manual for details on PM items serviced by service technician. -
Page 66: Special Tools
M047 Series Training - Kriss-P2 /Model Kr-P2 Special Tools ! SD Card " Part number: B6455010 » Used in common with other printers ! SD-to-PCMCIA Card Adapter " Part number: B6456705 » Used in common with other printers ! SD Card / USB Reader/Writer "... -
Page 67: Sd Card Slots
M047 Series Training - Kriss-P2 /Model Kr-P2 SD Card Slots ! See the following in the service manual: " SD Card Appli Move Slot-1 » Overview » Move Exec Slot-2 » Undo Exec Card Slot Cover Slide 67... -
Page 68: Cover Removal Procedures
M047 Series Training - Kriss-P2 /Model Kr-P2 Cover Removal Procedures ! Before removing machine's covers for the first time, see the following in the service manual for photos and details: " Exterior Covers » Operation Panel » Rear Cover » Upper Cover »... -
Page 69: Exterior Cover Removal
M047 Series Training - Kriss-P2 /Model Kr-P2 Exterior Cover Removal ! Remove exterior covers in the following order: " Operation Panel " Rear Cover " Upper Cover " By-pass Tray " Left Cover » Note: To remove the left cover, first remove the optional paper feed unit from the machine (if installed). -
Page 70: Replacing Print Cartridge
M047 Series Training - Kriss-P2 /Model Kr-P2 Replacing Print Cartridge Insert cartridge into printer until it Open front cover. [A] stops. [E] Lift & pull out Print Cartridge. [B] Push down on tonner cartridge to Wipe around metallic registration roller insure it's in correct position. - Page 71 M047 Series Training - Kriss-P2 /Model Kr-P2 Replacing Friction Pad - 1/2 Underside of paper tray ! Release catches of two Friction Pad pins with pointed object (such as a ball-point pen). " Note: Above view is of underside of picture tray.
- Page 72 M047 Series Training - Kriss-P2 /Model Kr-P2 Replacing Friction Pad - 2/2 ! Pull Friction Pad up and out of paper tray. Topside of paper tray ! Attach Friction Pad to its spring. ! Align Friction Pad pins with paper tray holes ! Push Friction Pad straight in until it clicks into position.
- Page 73 M047 Series Training - Kriss-P2 /Model Kr-P2 Replacing Paper Feed Roller ! After removing paper tray and duplex unit (if installed), place machine on edge of (stable) table as shown in illustration. ! Slide green lock to left. ! Remove Paper Feed Roller.
-
Page 74: Replacing Transfer Roller
M047 Series Training - Kriss-P2 /Model Kr-P2 Replacing Transfer Roller ! Remove Print Cartridge. [A] ! Push lock levers down on both ends, until they click into place. [E] ! Hold green parts of roller [B] and remove roller from printer. [C]... - Page 75 M047 Series Training - Kriss-P2 /Model Kr-P2 Removing Rear Cover or Duplex Unit Rear Cover ! Open Rear Cover Under ! Remove by pulling straight back. Board Levers Duplex Unit ! Push under-board levers. ! Pull Duplex Unit out of the printer.
-
Page 76: Replacing Fusing Unit
M047 Series Training - Kriss-P2 /Model Kr-P2 Replacing Fusing Unit ! Push new Fusing Unit into machine. ! Lift Lock Levers of Fusing Unit. [A] ! Pull Fusing Unit Out [B] ! Push locking levers of Fusing Unit ! Pull out new Fusing Unit pins from down until they click. -
Page 77: Loading Envelopes
M047 Series Training - Kriss-P2 /Model Kr-P2 Loading Envelopes ! Load envelopes with the flap fold on the left. ! Set printer driver to [Rotate by 180 degrees] ! Load envelopes with print side facing up on print tray. Slide 77... - Page 78 M047 Series Training - Kriss-P2 /Model Kr-P2 Removing Controller Board ! Turn off power and unplug machine. Screws ! Remove two screws. ! Pull out handle. ! Pulling handle, slide Controller Board out of machine and place on flat surface.
- Page 79 M047 Series Training - Kriss-P2 /Model Kr-P2 Reinstalling Controller Board ! Properly align Controller Board and slide in until it stops. ! Move handle to closed position. ! Reattach two screws to hold Controller Board in place. Slide 79...
-
Page 80: Updating The Firmware
M047 Series Training - Kriss-P2 /Model Kr-P2 Updating the Firmware ! See service manual for details on the following: " Type of Firmware " Precautions » Handling SD Cards » Upload/Download » Network Connection " Machine Firmware Update " Error Recovery »... - Page 81 M047 Series Training - Kriss-P2 /Model Kr-P2 Clamps & Binders ! Be sure to have all connections, clamps and binders in their correct places after servicing. Slide 81...
- Page 82 M047 Series Training - Kriss-P2 /Model Kr-P2 M047 Series Training Model Kr-P2 Laser Exposure Slide 82...
-
Page 83: Laser Unit
M047 Series Training - Kriss-P2 /Model Kr-P2 Laser Unit ! Review the following in the service manual: " Caution Decal Location » Warning: Be sure to turn off main power switch and disconnect power plug from power outlet before beginning any disassembly or adjustment of laser unit. - Page 84 M047 Series Training - Kriss-P2 /Model Kr-P2 M047 Series Training Model Kr-P2 Paper Feed Slide 84...
- Page 85 M047 Series Training - Kriss-P2 /Model Kr-P2 Paper Feed - Overview Slide 85...
-
Page 86: Paper Feed
M047 Series Training - Kriss-P2 /Model Kr-P2 Paper Feed ! See following sections in service manual for more details: " Paper Feed Roller » See also following slide " Friction Pad » See also following slide " Paper End Sensor "... - Page 87 M047 Series Training - Kriss-P2 /Model Kr-P2 Paper Feed Roller Paper Feed Roller ! To access Paper Feed Roller, first pull out paper tray. Slide 87...
-
Page 88: Friction Pad
M047 Series Training - Kriss-P2 /Model Kr-P2 Friction Pad Friction Pad ! To access Friction Pad, first open Paper Tray Slide 88... -
Page 89: Paper Feed Unit
M047 Series Training - Kriss-P2 /Model Kr-P2 Paper Feed Unit Slide 89... - Page 90 M047 Series Training - Kriss-P2 /Model Kr-P2 M047 Series Training Model Kr-P2 Fusing & Paper Exit Slide 90...
- Page 91 M047 Series Training - Kriss-P2 /Model Kr-P2 Overflow Sensor Paper Exit Roller Paper Exit Sensor Image Fusing Fusing Exit Sensor & Paper Exit Overview Thermistor Thermostat Fusing Exit Roller Pressure Spring Hot Roller Slide 91...
- Page 92 M047 Series Training - Kriss-P2 /Model Kr-P2 Fusing ! See the following in the service manual " Fusing Unit " Hot Roller and Fusing Lamp Hooks " Pressure Roller " Thermostat " Thermistor " Hot Roller Strippers Fusing Unit Rear Cover...
-
Page 93: Fusing Drive
M047 Series Training - Kriss-P2 /Model Kr-P2 Fusing Drive ! Main motor, through Transport Roller Paper gear train, drives: Exit Roller " hot roller " fusing exit roller " transport roller " paper exit roller Fusing Exit Roller Main Motor... -
Page 94: Paper Exit
M047 Series Training - Kriss-P2 /Model Kr-P2 Paper Exit ! Paper Exit Sensor ! Overflow Sensor ! Paper Exit Unit ! Fusing Exit Sensor ! See service manual for photos and details regarding above. Slide 94... - Page 95 M047 Series Training - Kriss-P2 /Model Kr-P2 M047 Series Training Model Kr-P2 Optional Duplex Unit - G806 Slide 95...
-
Page 96: Duplex Unit
M047 Series Training - Kriss-P2 /Model Kr-P2 Duplex Unit Slide 96 Be careful to remove all shipping tape from unit before installing. - Page 97 M047 Series Training - Kriss-P2 /Model Kr-P2 Duplex Unit - 1/3 Right Cover Left Upper Cover Cover Rear Upper Cover Remove covers: Upper Right Left Slide 97...
- Page 98 M047 Series Training - Kriss-P2 /Model Kr-P2 Duplex Unit - 2/3 Upper Cover Rear Lower Cover Remove covers: Upper Rear Lower Slide 98...
- Page 99 M047 Series Training - Kriss-P2 /Model Kr-P2 Duplex Unit Front Cover Slide 99...
- Page 100 M047 Series Training - Kriss-P2 /Model Kr-P2 Duplex Board Duplex Board Slide 100...
- Page 101 M047 Series Training - Kriss-P2 /Model Kr-P2 Inerter & Entrance Sensors Inverter Sensor Slide 101...
-
Page 102: Exit Sensor
M047 Series Training - Kriss-P2 /Model Kr-P2 Exit Sensor Exit Sensor Slide 102... -
Page 103: Inverter Motor
M047 Series Training - Kriss-P2 /Model Kr-P2 Inverter Motor Inverter Motor Slide 103... - Page 104 M047 Series Training - Kriss-P2 /Model Kr-P2 M047 Series Training Model Kr-P2 Optional Paper Tray Unit - M374 Slide 104...
- Page 105 M047 Series Training - Kriss-P2 /Model Kr-P2 PTU - Mechanical Component Layout Paper Feed Roller Friction Pad Bottom Plate Slide 105...
- Page 106 M047 Series Training - Kriss-P2 /Model Kr-P2 PTU - Electrical Component Layout Paper Feed Clutch Paper Feed Board Paper Size Switch Remaining Paper Sensor - 2 Remaining Paper Sensor - 1 Paper End Sensor Paper Feed Sensor Paper Feed Motor...
- Page 107 M047 Series Training - Kriss-P2 /Model Kr-P2 Paper Feed & Separation Paper Feed Clutch Paper Feed Motor Paper Feed Sensor Paper Feed Roller Friction Pad Slide 107...
- Page 108 M047 Series Training - Kriss-P2 /Model Kr-P2 PTU Paper Size Detection Paper Size Switch ! Manually set Paper Size Dial for correct paper size in drawer. ! Set "*" for wider range of paper sizes " Set via Paper Input Menu.
- Page 109 M047 Series Training - Kriss-P2 /Model Kr-P2 PTU Remaining Paper Detection ! Remaining paper detected by combination of Remaining Paper Remaining Sensor signals. Paper Sensor-2 Remaining ! Signals from Paper Sensor-1 these sensors indicates whether there are 500, 450, 250, or 50 sheets remaining.
- Page 110 M047 Series Training - Kriss-P2 /Model Kr-P2 PTU Paper End Detection ! When paper tray runs out of Paper End Sensor paper: " Feeler drops into cutout in Feeler bottom plate " Paper End Sensor is activated Slide 110...
- Page 111 M047 Series Training - Kriss-P2 /Model Kr-P2 PTU Paper Feed Roller Lever ! To remove Paper Feed Roller, first slide lever to left. Paper Feed Roller Slide 111...
- Page 112 M047 Series Training - Kriss-P2 /Model Kr-P2 ! Remove paper tray Paper Feed Unit unit from main unit. ! Pull out paper tray ! Turn paper tray unit over ! Remove three silver screws first " Do not remove other screws from this side.
- Page 113 M047 Series Training - Kriss-P2 /Model Kr-P2 Paper Feed Unit ! Remove Paper Feed Unit Slide 113...
- Page 114 M047 Series Training - Kriss-P2 /Model Kr-P2 Paper Feed Roller Lever ! To remove Paper Feed Roller, first slide lever to left. Paper Feed Roller Slide 114...
- Page 115 M047 Series Training - Kriss-P2 /Model Kr-P2 Friction Pad Friction Pad ! To access Friction Pad, first open Paper Tray Slide 115...
-
Page 116: Paper Feed Motor
M047 Series Training - Kriss-P2 /Model Kr-P2 Paper Feed Motor - 1/2 Slide 116... - Page 117 M047 Series Training - Kriss-P2 /Model Kr-P2 Paper Feed Motor - 2/2 Slide 117...
-
Page 118: Main Board
M047 Series Training - Kriss-P2 /Model Kr-P2 Main Board Main Board Slide 118... -
Page 119: Paper Size Switch
M047 Series Training - Kriss-P2 /Model Kr-P2 Paper Size Switch Paper Size Switch Slide 119... - Page 120 M047 Series Training - Kriss-P2 /Model Kr-P2 Paper Feed & Paper Feed Cover End Sensors Paper End Sensor Paper Feed Sensor Slide 120...
- Page 121 M047 Series Training - Kriss-P2 /Model Kr-P2 Remaining Remaining Paper Sensor - 1 Paper Sensors Remaining Paper Sensor - 2 Slide 121...
-
Page 122: Paper Feed Clutch
M047 Series Training - Kriss-P2 /Model Kr-P2 Paper Feed Clutch Paper Feed Gear Paper Feed Clutch Idle Gear Slide 122... - Page 123 M047 Series Training - Kriss-P2 /Model Kr-P2 M047 Series Training Model Kr-P2 Troubleshooting Slide 123...
-
Page 124: Image Adjustment
M047 Series Training - Kriss-P2 /Model Kr-P2 Image Adjustment - 1/2 Parallelogram Image Adjustment ! Use scanner positioning pin (P/N: A0069104) for adjustment. ! Do following procedure (next slide) if a parallelogram is printed while adjusting printing registration using a trimming pattern. - Page 125 M047 Series Training - Kriss-P2 /Model Kr-P2 Image Adjustment - 2/2 Parallelogram Image Adjustment ! Remove upper cover. ! Put positioning pin in one of the holes. ! Loosen four screws and move laser unit. ! Tighten laser unit. ! Print trimming area pattern to check image.
-
Page 126: Power-On Self Tests
M047 Series Training - Kriss-P2 /Model Kr-P2 Power-On Self Tests ! Controller tests following devices at power-on. If error is detected, error code is stored in controller board. " CPU, ASIC and clock " Flash ROM " Resident and optional SDRAM "... -
Page 127: Dip Switches
M047 Series Training - Kriss-P2 /Model Kr-P2 Dip Switches (Controller Board) ! DIP Switch 1 (Bit 1) C N 7 0 2 P C 2 1 0 0 on controller board is used for error recovery if firmware updating procedure fails. - Page 128 M047 Series Training - Kriss-P2 /Model Kr-P2 M047 Series Training Model Kr-P2 Energy Saving Slide 128...
- Page 129 M047 Series Training - Kriss-P2 /Model Kr-P2 Promote Use of Energy Saving Features ! Energy Saver Mode " Proper use of energy saver modes saves energy and is environmentally friendly. ! Duplex Settings " Use of Duplex settings reduces amount of paper used, which results in less energy consumption for paper production.
-
Page 130: Energy Saver Modes
M047 Series Training - Kriss-P2 /Model Kr-P2 Energy Saver Modes - 1/2 ! Energy saver mode should be utilized to save energy & protect environment. ! Area shaded grey in diagram above represents amount of energy saved. Slide 130... - Page 131 M047 Series Training - Kriss-P2 /Model Kr-P2 Energy Saver Modes - 2/2 ! Energy Saver Mode Setting " "Energy Saver" mode settings can be adjusted via User Mode (Menu > System > Energy Saver). " Energy Saver On/Off » You can activate or deactivate Energy Saver mode.
- Page 132 M047 Series Training - Kriss-P2 /Model Kr-P2 Paper Saving - 1/2 ! Duplexing and combine functions reduce amount of paper used. " Less energy overall is used for paper １ production, which helps the environment. ! Duplex: " Reduce paper volume by 50%! １...
- Page 133 M047 Series Training - Kriss-P2 /Model Kr-P2 Paper Saving - 2/2 ! Duplex + Combine: １ ! Using both features together can further reduce paper volume by 3/4! ! To check paper consumption, view total counter and duplex counter. " For one duplex page, total counter goes up by 2.
- Page 134 M047 Series Training - Kriss-P2 /Model Kr-P2 End of Course Slide 134...