Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Strongway 46193
Summary of Contents for Strongway 46193
- Page 1 1000-LB.LOW PROFILE TRANSMISSION JACK OWNER’S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. Item# 46193...
-
Page 2: Intended Use
Thank you very much for choosing a Strongway product! For future reference, please complete the owner’s record below: Model: _______________ Purchase Date: _______________ Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it. -
Page 3: Important Safety Considerations
SAVE THESE INSTRUCTIONS IMPORTANT SAFETY CONSIDERATIONS JACK USE AND CARE Do not modify the Jack in any way. Unauthorized modification may impair the function and/or safety and could affect the life of the equipment. There are specific applications for which the Jack was designed. -
Page 4: Safety Markings
DO NOT OPERATE OR REPAIR THIS EQUIPMENT WITHOUT READING THIS MANUAL. To maintain the Transmission Jack and user safety, the owner is responsible for reading and following these instructions. Inspect the service jack for proper operation and function. Keep instructions readily available for equipment operators. - Page 5 * Position the Jack Position the jack to only lift on the areas of the vehicle as specified by the vehicle manufacturer. * Always Use Jack Stands After lifting the vehicle always support the load with appropriately rated vehicle Jacks stands before working on the vehicle.
- Page 6 Spectators -Do not allow bystanders around the jack or under the load supported only by the jack. -Do not allow anyone in the vehicle while the jack is in use. Keep all bystanders away from vehicle when in use. Inspection -Inspect the jack carefully before each use.
- Page 7 2. Thread hex nut (73) part way up the chain hook (75) followed by a washer (74). Place through saddle and attach with washer (74), and hex nut (73). 3. Screw the pump handle (1) into the socket (2). 4. Tighten knob (26) clockwise to close the pump release valve. Pump handle up and down to lift the whole stroke.
- Page 8 SYSTEM AIR PURGE PROCEDURE IMPORTANT: BEFORE FIRST USE All numbers in parenthesis () refer to the index number from the parts breakdown. Perform the following Air Purge Procedure to remove any air that may have been introduced into the hydraulic system as a result of product shipment and handing. This step is to be completed without any weight on the jack.
-
Page 9: Before Use
BEFORE USE 1. Before using this product, read the owner's manual completely and familiarize yourself thoroughly with the product and the hazards associated with its improper use. 2. Perform the air purge procedure. (See previous instructions for system purge procedure.) 3. - Page 10 5. Adjust the angle brackets and the chain to secure the transmission on the saddle. 6. Remove the transmission from the vehicle. 7. Turn the knob (26) counter-clockwise slowly to lower the saddle. Always lower the saddle slowly. Always transport the load in the lowered position with the chains securely fastened. 8.
-
Page 11: Maintenance Instructions
MAINTENANCE INSTRUCTIONS If you use and maintain your equipment properly, it will give you many years of service. Follow the maintenance instructions carefully to keep your equipment in good working condition. Never perform any maintenance on the equipment while it is under a load. Inspection You should inspect the product for damage, wear, broken or missing parts (e.g.: pins) and that all components function before each use. - Page 12 TO ADD JACK OIL: The hydraulic cylinder assembly contains hydraulic fluid that must be kept at approximately 80% full at all times for proper operation. To check the level and to fill remove oil filler plug (30) 1. Position the jack on level ground and lower the saddle. 2.
- Page 13 3. Remove the oil fill plug. 4. Turn the jack on its side so that old oil will drain from the oil fill hole. 5. Position the jack on level ground and lower the saddle.
- Page 14 6. Fill the oil case until oil level to 80% full. KEEP DIRT AND OTHER MATERIAL CLEAR WHEN POURING. 7. Replace oil plug. 8. Perform the Air Purge Procedure. ADDITIONAL WARNINGS: DO NOT USE MOTOR OIL IN THE JACK. ...
- Page 15 LUBRICATION 1. Lubricate the shaft threads of the angle screw assembly (59&66) with #2 tube grease when necessary. 2. A coating of light lubricating oil to pivot points. Axles and hinges will help to prevent rust and assure that wheels, casters and pump assemblies move freely. 3.
-
Page 16: Troubleshooting
4. When not in use, store the Jack with pump piston and ram fully retracted (36). TROUBLESHOOTING JACK JACK JACK POOR WILL NOT WILL WILL WILL JACK LIFT TO CAUSES AND SOLUTIONS LIFTING FULL LIFT HOLD LOWER EXTENSION LOAD LOAD ... -
Page 17: Assembly Diagram
ASSEMBLY DIAGRAM... -
Page 18: Assembly Parts List
ASSEMBLY PARTS LIST Index # Description Part No. Qty. Handle TE05001-01 Socket TE05001.3-09 Spring Pin QLQD2B-3 Shaft T90403-19 Shot Shaft T90403-34 Rod Link TE05001.3-11 Plunger TE05001.3-13 O-Ring 8.7X1.9 TE05001.3-14 Back Ring TE05001.3-15 Umbrella Washer TE05001.3-16 Pump Cylinder TE05001.3-12 Pump Washer TQ22001.1-30 Gyration Body TE05001.3-10... - Page 19 Index # Description Part No. Qty. Pin 4X40 GB91 Below Block Ring TE05001.3-03 O-Ring 30.3X4.1 TE05001.3-02 Above Block Ring TE05001.3-01 Ring Snap TE05001.3-18 Arm Shaft TE05001-02 Ring Snap 22 GB894.1 Frame TE05001.1 Nut M18 GB41 Spring Washer 18 GB93 Wheel Parts TE05001.5 Arm Parts TE05001.2...
-
Page 20: Replacement Parts
Safe Operating Temperature is between 40°F – 105°F (4°C - 41°C) REPLACEMENT PARTS For replacement parts Customer Service at 1-800-222-5381. Not all equipment components are available for replacement; illustrations provided are a convenient reference of location and position in the assembly sequence. - Page 21 Northern Tool and Equipment Company, Inc. ("We'' or '"Us'') warrants to the original purchaser only ("You'' or “Your”) that the Strongway product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.