Sample Predelivery Checklist - BRP Evinrude E-TEC G2 150 HP Installation & Predelivery Manual

Sample Predelivery Checklist

PREDELIVERY CHECKLIST
OB MODEL NUMBER
1
2
3
4
IMPORTANT: Use this Checklist together with the Evinrude E-TEC G2 Installation and Predelivery Guide. Every Evinrude Dealer is re-
sponsible to perform a complete predelivery inspection on all Evinrude E-TEC G2 outboards. If an Evinrude E-TEC G2 outboard was pre-
rigged by the boat builder, a complete predelivery inspection is still required. Refer to the current Evinrude E-TEC G2 Installation and Pre-
delivery Guide for detailed instructions. Dealer predelivery programs should include additional inspections related to boat accessories and
trailers.
At Time of Sale
Explain to owner all on-product Safety
Labels/Tags and the importance of reading the
Operator's Guide before operating engine(s)
Install engine Safety Labels/Tags
chosen by customer according to availability)
Explain the BRP Limited Warranty
Explain selection of outboard lubricant
Owner's outboard oil selection:
XD100 XD50
New boat package Repower
Transom height 20"
Remote Control (
with start-in-gear protection)
Evinrude / BRP Other
Single lever binnacle
Concealed side mount
•Mechanical Controls (with MCM Converter)
Evinrude BRP control cables
Other (list brand) ____________________
Key switch with tether cord
MWS harnesses
•BRP Electronic Controls
Electronic Shift & Throttle
Remote control harness
Network power cable
(extension - optional)
Master power / key switch
Buss cables
6-Port hubs
use as needed
Engine cut-off switch panel 2nd station
Accessory tank connection & protective cap
Displays, Gauges and Networks
Digital display(s)
Network buss cables and T-connectors
NMEA 2000 Network terminators (2)
Tachometer set to 6 pulse -
Outboard Installation
Mounting height - correct shaft length?
Transom position - 3 and 4 outboards only
Mounting hardware - torqued?
Water pressure transducer -
The dealer named in this document has instructed me on the operation, maintenance, safety features, and warranty policy for my outboard, all of
which I understand. I am satisfied with the predelivery set-up and inspection of my outboard. I acknowledge that I have reviewed the on product
safety labels and tags. I understand the importance of reading the operator's guide that I have received completely and thoroughly before operating
the engine(s).
Inspected by: _____________________________________
Dealer name: _____________________________________
Dealer number: ___________________________________
Date
Revision B
SERIAL NUMBER
Steering System
Correct helm selection
Fill/bleed/check hydraulic system
Tie bar kit correctly installed
(language
Set multi-engine alignment (toe-in/toe-out)
Calibrate Steering Position Sensors - AFA &
newer outboard models
Batteries, Wiring, and Switches
Batteries: Qty. ______ CCA Rating _______
Cable size: ____ ga. Length:_____ ft. / m
Connections tight – NO wing nuts!
25" 30"
Battery switch operation
Auxiliary battery charging
Fuel System
Dual lever binnacle
Fuel hose - "SAE J30R9 type"
Surface side mnt
Fuel hoses installed with Oetiker clamps
Water separating fuel filter kit
Remote Oil Tank
Correct installation
Oil Hose - 25 ft. [7.6 m] maximum,
Remote oil fill kit (vent not restricted)
Pre-Start Up:
•Oil and Fuel Set Up, Check Fluid Levels
Fill oil tank(s) with outboard lubricant
Check fuel level
Check if fuel or oil hoses are kinked
Check gearcase lubricant level
•Evinrude Diagnostics Software Set Up
Set multi-engine identity
Calibrate trim gauge as needed
Set tilt limit
Set water pressure transducer (50 psi)
Electronic shift & throttle (Dual station only)
set station protect
SystemCheck
•Digital Display Set Up
Set "Engine and Fuel Tank Configuration"
and "Fuel Tank Capacity"
Set "Engine Data"
installed
Dealer Signature
Sample Predelivery Checklist
KEY NUMBER
Start Up / Operational Checks
Prime fuel system
(see Installation Guide)
Check start-in-gear prevention
Check remote control operation
(multiple engines)
Check key switch and engine cut–off switch
Check display/gauge operation
(multiple engines) Check operation of trim and tilt switches
Water pressure / overboard indicator
Engine temperature IDLE _______ °F
No Fuel, Oil or Water leaks
Electronic Shift & Throttle Checks
optional Start/Stop Switch(es)
optional Engine Cut–off Switch
Neutral Throttle Switch
3/8
RPM Switch
Trim Switch Panel
Propeller(s)
recommended
optional Evinrude BRP
Stainless Steel
no splices
Diameter _________ Pitch __________
optional
Torque _______
Cotter pin keeper and cotter pin installed
On the Water Operational Checks
Engine RPM at IDLE (in gear) ___________
Engine RPM at WOT __________________
Engine temperature WOT______ °F or
Water pressure at IDLE _________ psi / kPa
Water pressure at WOT _________ psi / kPa
Adjust multi-engine alignment (toe-in/toe-out)
as needed for optimum water pressure
At time of delivery dealer:
Complete electronic warranty registration
Must retain this document with outboard file
optional
Give owner a completed copy of this form
(See User's Guide)
(See User's Guide)
Where not already required by law: I recognize the importance of
following safe boating practices.
I have taken a safe boating course before using the outboard.
I will take a safe boating course before using the outboard.
I will not take a safe boating course before using the outboard.
Date
Predelivery
*357899*
°C
or
(2nd station only)
(3 or 4 engines only)
Aluminum
ft.lbs. N·m
°C
Owner / Customer
P/N 0357899-00
101
6