THOMSON ASR08T User Manual

Thomson multimedia satellite receiver user manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

To take maximum advantage of all the features of your satellite receiver,

please read this user manual very carefully.

ASR 08 T SATELLITE RECEIVER

The package contains the following items :

• Satellite receiver

• Remote control unit

• SCART cable

• Two batteries, type R03 (AAA)

• User manual

• List of pre-programmed channels

In the unlikely event of one of these items being missing, please contact your dealer.

REMOTE CONTROL

Installing the batteries

Remove the battery compartment cover,

located at the back of the remote control unit.

Insert the two 1.5-V (AAA) batteries.

Be sure to observe polarity.

For your information

If the remote control seems to have stopped operating correctly,

replace the batteries.

Warning

- Do not expose the batteries to excessive heat (sun, fire, etc.).

- Do not recharge ordinary batteries.

- Do not let children play with batteries; they may try to swallow them.

- Consult a doctor immediately if a battery has been swallowed.

Protect the environment!

• Do not dispose of used batteries via the rubbish bin.

• Place them in the containers provided for this purpose.

• Find out where such containers are located in your area.

Table of Contents

Summary of Contents for THOMSON ASR08T

Page 1: Remote Control
To take maximum advantage of all the features of your satellite receiver, please read this user manual very carefully. ASR 08 T SATELLITE RECEIVER The package contains the following items : • Satellite receiver • Remote control unit • SCART cable •...
Page 2 Important safety and operating information. This set was designed and manufactured in accordance with international safety standards. You must nonetheless observe certain rules to guarantee optimum results and safety. Read this user manual before attempting to put the set into service. Ensure that all connections (including mains connection and connector cables between sets) are made according to manufacturer recommendations.
Page 3: Table Of Contents
CONTENTS Page REMOTE CONTROL UNIT ... 5 FRONT PANEL KEYPAD ... 6 REAR PANEL CONNECTIONS... 6 INSTALLATION OF SATELLITE RECEIVER ... 7-8 EVERYDAY USE ... 9 RECORDING SATELLITE PROGRAMMES ...10 PROGRAMMING A NEW CHANNEL ...11-12 SPECIAL FEATURES...13-14 CONVENIENCE FEATURES ...15 TROUBLESHOOTING...16 SPECIFICATIONS...16-17...
Page 4: Remote Control Unit
REMOTE CONTROL UNIT EXIT COPY TUNE TUNE VIDEO AUDIO 22 KHZ C/KU STORE STORE STANDBY key (Switch set on using the keys, or 0 to 9) Parental lock. Numeric keypad : - Channel selection - Frequency entry - Toturn on the receiver. Channel scrolling (zapping) and to turn on the receiver.
Page 5: Front Panel Keypad
FRONT PANEL KEYPAD Satellite receiver ASR08T 400 programs Sound Wegener Panda DiSEqC ToneBurst REAR PANEL CONNECTIONS IF A input - socket to connect the LNB of your satellite antenna (e.g. ASTRA) video cassette recorder (VCR) MADE IN GERMANY IF INPUT...
Page 6: Installation Of Satellite Receiver
INSTALLATION OF SATELLITE RECEIVER A correctly installed satellite antenna is essential for the receiver to operate. The satellite antenna coaxial cable must be long enough to reach the desired receiver site. Install the receiver near your television set, making sure to leave ventilation space of about 15 cm to the sides and above the receiver.
Page 7 INSTALLATION OF SATELLITE RECEIVER - Connect the LNB coaxial cable to Socket - You can, if applicable, connect a second LNB to IF INPUT B connector tightened by hand on the threading of the plug. Do not use any tools. Take care not to jam the plug.
Page 8: Everyday Use
EVERYDAY USE On/Standby Using set keypad: Press the On/Standby key. Using remote control: Switch the receiver on by pressing one of the numeric keys (0 to 9), remote control keypad. If the set is switched on using the before switching off is called up, for example : " 13". To switch the set off, press the Standby key.
Page 9: Recording Satellite Programmes
RECORDING SATELLITE PROGRAMMES If your receiver is connected to a VCR, you can record satellite programmes. Paragraph 2 : Connection to a VCR in the INSTALLATION OF SATELLITE RECEIVER chapter of the present manual describes the procedure for connecting the VCR to the receiver. Refer also to your VCR user manual.
Page 10: Programming A New Channel
PROGRAMMING A NEW CHANNEL Your receiver is already programmed to receive the most important satellite signals. You can, however, change the programming or add new channels at any time. To store a new channel in memory, you need the following information (found in specialist satellite TV magazines): 1.
Page 11 PROGRAMMING A NEW CHANNEL 4. Audio mode selection Press the key to display the audio mode, e.g. : "Ton1". Press several times to display all the available modes. DISPLAY MODE "Ton 1" Stéréo "Ton 2" Mono "Ton 3" Mono "Ton 4" Mono "Ton 5"...
Page 12: Special Features
SPECIAL FEATURES 1. Video Level This feature lets you adjust the video level to compensate for differences in level that may exist between the various satellites. Press the key to display the current mode, e.g. : " HI ". Press the key again to select the second mode. "...
Page 13 SPECIAL FEATURES 4. 22 kHz Switching Signal This signal can be used to control either a switching box or, for example, the LNB (high band/low band). Press the key briefly to display the current mode, e.g. : "22-". 22 KHZ Press again to select the second mode.
Page 14: Convenience Features
CONVENIENCE FEATURES 1. Parental Lock Used to restrict use of the set, or access to certain programmes. 1. Locking certain programmes. The programme can be selected, but the picture does not appear on screen. The programming cannot be altered. Locked programmes are indicated on the display by an L before the programme number, e.g.
Page 15: Troubleshooting
TROUBLESHOOTING SYMPTOM Display inoperative Unable to switch set on No picture No sound Poor picture quality Remote control inoperative Display : FAIL SPECIFICATIONS - 399 PROGRAMME NUMBERS, ALL PROGRAMMABLE - 2 IF INPUT - PLL FREQUENCY ADJUSTMENT SYSTEM - 2 AUDIO BANDWIDTH - MULTI-PURPOSE LED DISPLAY - 3 SCART SOCKETS FOR TELEVISION SET, VCR AND DECODER - 14 V/18 V LNB POWER SUPPLY SWITCHING...
Page 16 SPECIFICATIONS RF PART - INPUT FREQUENCY : 900-2150 MHz (IN STEPS OF 1 MHz) - INPUT IMPEDANCE : 75 OHM - INPUT LEVEL : -60 dBm -30 dBm - INTERMEDIATE FREQUENCY : 479.5 MHz - RESPONSE THRESHOLD : 6 dB VIDEO PART - DE-EMPHASIS : CCIR REC 405-1, 625 LINES - FREQUENCY RESPONSE : 50 Hz - 4,0 Mhz (+1,5 dB / - 2 dB)