Ricoh E-25C Start Manual
  1. Manuals
  2. Brands
  3. Ricoh Manuals
  4. Printer Accessories
  5. E-25C
  6. Start manual

Ricoh E-25C Start Manual

Color controller
Hide thumbs Also See for E-25C:
Table of Contents

Advertisement

Quick Links

Download this manual
Start Guide
1.
Getting Started
2.
Using Color Controller
Read this manual carefully before you use this machine and keep
it handy for future reference. For safe and correct use, be sure to
read the Safety Information in this manual before using the
machine.

Advertisement

Table of Contents
loading

Related Manuals for Ricoh E-25C

Summary of Contents for Ricoh E-25C

  • Page 1 Getting Started Start Guide Using Color Controller Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the Safety Information in this manual before using the machine.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS FCC Warning ..................... A-1 Note to users in the United States of America ..........A-1 Notes to Canadian Users of ICES-003 Conformance ......... A-2 User Information on Electrical and Electronic Equipment ....A-3 Users in the countries where this symbol shown in this section has been specified in national law on collection and treatment of E-waste ....
  • Page 4 A-ii...

  • Page 5: Fcc Warning

    (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Responsible party: Ricoh USA, Inc. Address: 70 Valley Stream Parkway Malvern, Pennsylvania 19355 Telephone number: 610-296-8000...

  • Page 6: Notes To Canadian Users Of Ices-003 Conformance

    Using the Shield Cable Properly shielded and grounded cables and connectors must be used for con- nections to a host computer (and/or peripheral) in order to meet FCC emission limits. Installing the Ferrite Core A network interface cable with a ferrite core must be used for RF interference suppression.

  • Page 7: User Information On Electrical And Electronic Equipment

    User Information on Electrical and Electronic Equipment Users in the countries where this symbol shown in this section has been specified in national law on collection and treatment of E-waste Our Products contain high quality components and are designed to facilitate recycling.

  • Page 8: Note For The Battery And/Or Accumulator Symbol (For Eu Countries Only

    Note for the Battery and/or Accumulator Symbol (For EU countries only) In accordance with the Battery Directive 2006/66/EC Article 20 Information for end-users Annex II, the above symbol is printed on batteries and accumulators. This symbol means that in the European Union, used batteries and accumula- tors should be disposed of separately from your household waste.

  • Page 9: Notes To Users In The State Of California (Notes To Users In Usa

    Notes to users in the state of California (Notes to Users in USA) This device complies with California Battery Charger Systems Regulations (California code of regulations title 20, sections 1601 through 1608).

  • Page 10: Safety Information

    Safety Information Safety During Operation In this manual, the following important symbols are used: WARNING: Indicates a potentially hazardous situation which, if instructions are not followed, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation which, if instructions are not followed, may result in minor or moderate injury or damage to property.
  • Page 11 CAUTION: • Do not place the machine in a humid or dusty environment. Doing so can result in fire or electric shock. • Do not place the machine on an unstable or tilted surface. Doing so can cause the machine to fall or topple over, possibly resulting in injury. •...
  • Page 12 CAUTION: • If you do not use the machine for a long period of time such as consecutive holidays, be sure to disconnect the power cord plug from the wall outlet for reasons of safety. • Be sure to push the power cord plug fully into the wall outlet. Also, do not push it into loose and unstable wall outlets likely to cause a contact failure.
  • Page 13 • If the machine behaves unusually as follows, turn off the power immediately. After turning off the power, make sure to disconnect the power cord plug from the wall outlet, and then contact your service representative and report the problem. Continuously using the power cord can result in fire or electric shock.
  • Page 14 Handling the machine’s supplies This section explains safety precautions about handling the machine’s supplies. CAUTION: • Use only the type of batteries specified by the manufacturer. There is a risk of explosion if a battery is replaced with an incorrect type of battery. Dispose of used batteries according to the instructions.

  • Page 15: Getting Started

    1. Getting Started Read this document before installing or using Color Controller. ❒ Ricoh supplied and is responsible for all the material provided in this docu- ment. If you have questions regarding the material contained in this docu- ment, please contact your local Ricoh supplier company.

  • Page 16: Guide To Components

    Getting Started Guide to Components EBA002 Power switch Not used (monitor port) See page A-17 “Color Controller Startup, Network connector 10/100/1000Mbps Shutdown, and Restart”. A port for connecting Color Controller to Front side USB port a LAN. Port for installing system software, acti- Network connector 10/100/1000Mbps vating Fiery features, or printing from a A port for connecting Color Controller to...

  • Page 17: Positioning Color Controller

    Positioning Color Controller Positioning Color Controller Caution • Insert firmly the plug in the outlet. • Avoid using an outlet extension plug or cord. • Ground Color Controller. Avoid using a 3-prong adapter in a 2-hole un- grounded outlet. • Do not put anything on the power cord. Space Required for Installation Place Color Controller near the power source, providing margins as shown.

  • Page 18: Dimensions And Weight

    Getting Started Dimensions and Weight • Weight: 5.5 kg (12.1 lb.) • Dimensions: Length: 362.5 mm (14.3 inches) Height: 294.6 mm (11.6 inches) Width: 124.3 mm (4.9 inches) Environment Environmental specifications Operating Ambient temperature 5 °C to 40°C (41 °F to 104 °F) Relative humidity 10% to 85% (non-condensing) Altitude...

  • Page 19: Moving Color Controller

    Moving Color Controller Moving Color Controller CAUTION: • When disconnecting the power cord from the wall outlet, make sure to pull the plug, not the cord. Do not pull the power cord forcibly. Doing so can damage the power cord, possibly resulting in fire or electric shock. CAUTION: •...
  • Page 20 Getting Started A-16...

  • Page 21: Using Color Controller

    2. Using Color Controller Color Controller Startup, Shutdown, and Restart The main unit and Color Controller have separate power switches. It is recom- mended to keep Color Controller activated for normal operations. Starting the Main Unit and Color Controller Turn on the main power switch of the main unit. Turn on the main power switch of Color Controller.

  • Page 22: Shutting Down Color Controller Only

    Getting Started Shutting Down Color Controller Only Press the Home key on the control panel, and press the [Fiery] icon on the [Home] screen. Press [Fiery]. Press [Restart Fiery]. Press [Shut Down], and then press [OK]. ❒ Do not turn off the main power switch of Color Controller when the power indicator remains lit.

  • Page 23: Power Up Sequence

    Power Up Sequence Power Up Sequence The Color Controller initial configuration is described as follows: If system software is reinstalled, language, password, and setup will need to be reconfigured. DQL003 A-19...
  • Page 24 MEMO A-20...
  • Page 25 © 2018...
  • Page 26 D3GF-6753...

Table of Contents