York 28229 Operating Instructions

2. Press the or q button to select 'Frame Rate' and then press the 'OK' button.
3. Press the or q button to toggle between different frame rates. Once you have
highlighted your desired selection, press the 'OK' button to confirm and exit.
Time Stamp Setting
1. In the setting mode, press the or q button to select 'RECORDER SETTING'
and then press 'OK' button.
2. Press the or q button to select 'Time Stamp' and then press the 'OK' button.
3. Press the or q button to toggle between on and off. Once your desired selection
is made, press the 'OK' button to confirm and exit.
Recording Type
1. In the setting mode, press the or q button to select 'RECORDER SETTING'
and then press 'OK' button.
2. Press the or q button to select 'Recording Type' and then press the 'OK' button.
3. Press the or q button to toggle between 'still' and 'video'. Once your desired
selection is made, press the 'OK' button to confirm and exit.
Event Playback
1. In the setting mode, press the or q button to select 'EVENT PLAYBACK' and
then press 'OK' button.
2. Refer to the user manual instructions on Playback of Video/Picture, Deleting
Video/Picture and Deleting Folder for guidance.
TROUBLESHOOTING
Problem Possible Cause Likely Solutions
1. Charge monitor
1. Monitor not charged
Tool will not start 2. Replace batteries in control
2. Batteries need charging
handle
1. Make sure adaptor cable is
1. Adaptor cable not attached connected between monitor
Monitor will not properly and adaptor
charge 2. Adaptor not connected to 2. Make sure adaptor is
power securely plugged into wall
socket
1. Use dial on control handle to
1. LEDs near camera need
adjust brightness of LEDs
Image too dark adjustment
2. Use contrast and brightness
or light 2. Monitor display needs
buttons on monitor to adjust
adjustment
image
Follow all safety precautions whenever diagnosing or servicing the tool.
Disconnect power supply before service.
Follow us!
Prospect House, George Cayley Drive, Clifton Moor, York, England YO30 4XE
York Survey Supply Centre
@York_Survey
E-Mail: sales@yorksurvey.co.uk
@York_Survey
Ref:.. \operat98\instructions 19\28229.qxp 17-01-19
SPECIFICATIONS
Imaging Sensor
Total Pixels
Horizontal Viewing Angle
Transmission Frequency
c
Minimum Illumination
a
Modulation Type
m
e
Bandwidth
r
Power Supply
a
Unobstructed Effective Range
Waterproof Capacity
Tube Diameter
Dimensions (WxDxH) 186 x 145 x 41mm (excluding flexible tube)
Approx. Weight
LCD Screen Type
Effective Pixels
Video System
Transmission Frequency 2414MHz, 2432MHz, 2450MHz, 2468MHz
Exterior Supply Voltage
m
Consumption Current (Max.)
o
Charging Time
n
i Working Time
t
Picture/Video Pixels
o
Video Size
r
Frame Rate
Video Output Level
Receiving Sensitivity
Dimensions (WxDxH)
Approx. Weight
Operating Temperature -10°C to +40°C / +14°F to +104°F
Operating Humidity (Max.)
Actual transmission range of wireless monitoring may vary according to the weather,
location, interference or building construction.
All specifications are subject to minor change without notice.
FCC INFORMATION
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation. Changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to operate the
equipment.
The graphics included in this user manual are subject to minor change without notice.
Tel: +44 (0) 1904 692723 Fax: +44 (0) 1904 690385
www.yorksurvey.co.uk
CMOS
640 x 480 (PAL)
640 x 480 (NTSC)
36°
2468MHz
0 Lux
FM
18MHz
4x AA batteries
10m (max)
IP67 (for lens/tube only)
9mm
408g
3.5" TFT-LCD
960 x 240
PAL/NTSC
5VDC
500mA
3 hours
2 hours
640 x 480
20M byte/minute
30 frame/second
0.9-1.3VP-P@75ohm
<-85dBm
100 x 70 x 25mm
140g
15 to 85%RH
Explorer Premium
Video Borescope
Code: 28229
Operating
Instructions
©York Survey Supply Centre 2019