BRP GTX Series Operator's Manual
  1. Manuals
  2. Brands
  3. BRP Manuals
  4. Boat
  5. GTX Series
  6. Operator's manual

BRP GTX Series Operator's Manual

Personal watercraft
Hide thumbs Also See for GTX Series:
Table of Contents

Advertisement

Quick Links

Download this manual
SERIES

Advertisement

Table of Contents
loading

Related Manuals for BRP GTX Series

Summary of Contents for BRP GTX Series

  • Page 1 SERIES...
  • Page 2 Disregarding any of the safety precautions and instructions contained in this Operator’s Guide, cause injury including the possibility of death! This watercraft may exceed the performance of other boats you may have ridden in the past. Take time to familiarize yourself with your new water- craft.

  • Page 3: Foreword

    FOREWORD Congratulations on your purchase of a new Sea-Doo ® craft (PWC). It is backed by the BRP warranty and a network of authorized Sea-Doo personal watercraft dealers ready to provide the parts, service or accessories you may require. Your dealer is committed to your sat- isfaction.
  • Page 4 FOREWORD any obligation to install them on prod- ucts previously manufactured. Due to late changes, some differences be- tween the manufactured product and the descriptions and/or specifications in this guide may occur. BRP reserves the right at any time to discontinue or change specifications, designs, fea- tures, models or equipment without incurring any obligation upon itself.

  • Page 5: Table Of Contents

    TABLE OF CONTENTS FOREWORD ................1 Know Before You Go ..
  • Page 6 TABLE OF CONTENTS PRE-RIDE INSPECTION (cont’d) Ski/Wakeboard Post ............36 Ballast Tanks .
  • Page 7 SPECIAL PROCEDURES (cont’d) Towing the Watercraft in Water ..........79 MAINTENANCE INFORMATION MAINTENANCE SCHEDULE .
  • Page 8 TABLE OF CONTENTS CALIFORNIA YORK EMISSION CONTROL WARRANTY STATEMENT FOR MODEL YEAR 2009 SEA-DOO ® PERSONAL WATERCRAFT ® WITH 4-TEC ENGINES ............126 BRP INTERNATIONAL LIMITED WARRANTY: 2009 SEA-DOO ®...

  • Page 9: Safety Information

    SAFETY INFORMATION ________ ________ SAFETY INFORMATION...

  • Page 10: General Precautions

    GENERAL PRECAUTIONS Avoid Carbon Monoxide Poisoning All engine exhaust contains carbon monoxide, a deadly gas. Breathing car- bon monoxide can cause headaches, dizziness, drowsiness, nausea, confu- sion and eventually death. Carbon monoxide is a colorless, odor- less, tasteless gas that may be present even if you do not see or smell any en- gine exhaust.

  • Page 11: Special Safety Messages

    SPECIAL SAFETY MESSAGES Reminders Regarding Operation The performance of this watercraft may significantly exceed that of other craft you may have operated. Make sure you read and understand the content of the Operator's Guide to become completely familiar with the controls and operation of the watercraft before embarking on your first trip or taking on a passen- ger(s).
  • Page 12 SPECIAL SAFETY MESSAGES Do not exceed the payload or pas- senger capacities for your water- craft, which are listed on the capac- ity plate and in the specifications. Overloading can affect maneuver- ability, stability and performance. Also, heavy seas reduce capacity. A payload or person capacity plate is not an excuse for failure to use com- mon sense or good judgment.

  • Page 13: Water Sports

    At least one passenger should be able to operate the watercraft in case the operator is unexpectedly unable to do so. Operation of this PWC by a person under 16 years of age or a person with a disability that impairs vision, reaction time, judgment, or opera- tion of the controls is NOT recom- mended.
  • Page 14 SPECIAL SAFETY MESSAGES Participate in water sports only in safe areas. Stay away from other boats, channels, beaches, restricted areas, swimmers, and heavily traveled waterways and un- derwater obstructions. Turn off engine and anchor the wa- tercraft before swimming. Swim only in areas designated as safe for swimming.
  • Page 15 SPECIAL SAFETY MESSAGES SKIING SIGNALS For more information about water skiing, please contact the American Water Ski Association, 1251 Holy Cow Road, Polk City, FL 33868 (1 863 324-4341). INTERNET WEB SITE: www.usawaterski.org/ E-MAIL: usawaterski@usawaterski.org ________ ________ SAFETY INFORMATION...

  • Page 16: Hypothermia

    SPECIAL SAFETY MESSAGES Hypothermia Hypothermia, the loss of body heat to the water, is a significant cause of deaths in boating accidents. After an individual has succumbed to hypother- mia, he or she will lose consciousness and then drown. PFDs can increase survival time be- cause of the insulation they provide.

  • Page 17: Safety Equipment

    SAFETY EQUIPMENT Required Safety Equipment Always carry the regulatory safety items and have them conveniently on board available for use. Check the local regulations or consult your authorized Sea-Doo dealer. Such required safety items usually include, without limita- tion, a sound signaling device such as a whistle, a watertight flashlight or ap- proved flares, a buoyant heaving line, an anchor and rope*, a bailer*, and...
  • Page 18 SAFETY EQUIPMENT PFD Types There are five types of approved PFDs. PFD Type I, Wearable has the greatest required buoyancy. Its design allows for turning most unconscious persons in the water from face down position to a vertical or slightly backward, face-up position.

  • Page 19: Additional Recommended Equipment

    PFD Type V, Wearable must be worn. When inflated, it provides buoyancy equivalent to Type I, Il or III PFDs. When it is deflated, however, it may not support some people. Helmets Some Important Considerations Helmets are designed to offer some degree of protection in case of im- pact to the head.

  • Page 20: Safe Boating Practices

    SAFE BOATING PRACTICES YOU are responsible for your own safety, the safety of your passengers, and the safety of fellow boaters. Ride smart from the start and we all win! Drugs and Alcohol Do not use drugs or drink alcohol while operating a PWC.
  • Page 21 Operator/Passenger Awareness The watercraft operator has the re- sponsibility to inform passenger(s) of safety measures. Never turn handlebar while some- one is nearby rear of watercraft. Keep away from steering moving parts (nozzle, side vanes, linkage, etc.). Do not start or operate the water- craft if anyone is seated on the sun deck, if so equipped, or swim plat- form, or is nearby in the water.
  • Page 22 SAFE BOATING PRACTICES Always carry an observer when pulling a tube, skier or wakeboarder, proceed with only as much speed as required and follow the observer’s instructions. Unless absolutely nec- essary, do not make tight, sharp turns. Keep a safe distance from the docks, other swimmers, craft or objects.

  • Page 23: Rules Of The Road

    RULES OF THE ROAD Operating Rules Operating a watercraft can be com- pared with driving unmarked highways and roads. To prevent collisions or avoid other boaters, a system of oper- ating rules must be followed. It’s not only common sense... it’s the law! Generally keep to your right and safely avoid other craft by keeping a safe dis- tance from other craft, people and ob-...
  • Page 24 RULES OF THE ROAD Collision Avoidance Do not release throttle when try- ing to steer away from objects. You need throttle to steer. Always keep a constant lookout for other water users, other boats or objects, especially when turning. Be alert for conditions that may limit your visibility or block your vision of others.

  • Page 25: Fueling Procedure

    FUELING PROCEDURE Recommended Fuel Use unleaded gasoline with the follow- ing octane rating. MINIMUM OCTANE RATING Inside 87 (RON + MON)/2) North America Outside North America On supercharged models, use super unleaded fuel for optimum engine per- formance. NOTICE Never experiment with other fuels or fuel ratios.

  • Page 26: Trailering

    TRAILERING NOTICE avoid O.P.A.S. side vanes, the maximum trailer wood bunks span including bunk width should not exceed 71 cm (28 in). Ends of both trailer wood bunks should not be more than 2.59 m (102 in) away from watercraft bow attachment point.

  • Page 27: Launching/Loading

    WARNING The bungee cords are under ten- sion and could spring back and whip someone when released. Use caution. NOTE: When trailering 2 watercraft, it may be necessary to remove the inner wakeboard rack. WARNING Never tow a watercraft with water remaining in the ballast tanks.

  • Page 28: Location Of The Important Labels

    LOCATION OF THE IMPORTANT LABELS The following labels are on your watercraft. If missing or damaged, they can be re- placed free of charge. See an authorized Sea-Doo dealer. Please read the following labels carefully before operating this watercraft. smo2008-001-002_c GTI™...
  • Page 29 smo2008-001-004_b TYPICAL — X PACKAGE MODELS smo2009-001-200_en LABEL 1: TYPICAL — GTX, WAKE AND RXT MODELS ________ SAFETY INFORMATION LOCATION OF THE IMPORTANT LABELS ________...
  • Page 30 LOCATION OF THE IMPORTANT LABELS LABEL 1: TYPICAL — RXP MODELS _______ ________ SAFETY INFORMATION...
  • Page 31 smo2006-002-013 LABEL 1: GTI MODELS LABEL 2 LABEL 3: MODELS EQUIPPED WITH A BOARDING STEP ________ LABEL 4 LABEL 5 LABEL 6 SAFETY INFORMATION LOCATION OF THE IMPORTANT LABELS ________...
  • Page 32 LOCATION OF THE IMPORTANT LABELS LABEL 7: TYPICAL LABEL 8 LABEL 9: TYPICAL _______ LABEL 10 LABEL 11: SUPERCHARGED ENGINES ONLY LABEL 12 smo2007-002-025 LABEL 13 SAFETY INFORMATION ________...
  • Page 33 WAKE MODELS LABEL 14 LABEL 15 ________ Not shown: Label 16 WITH FULL BALLAST TANKS DO NOT: – Use in waves. – Jump waves. – Operate over 50 km/h (30 MPH). – Perform abrupt maneuvers. Handling characteristics of the watercraft could be affected. NEVER: –...
  • Page 34 LOCATION OF THE IMPORTANT LABELS Watercraft Outside North America smo2006-002-015 LABEL 17: ALL MODELS EXCEPT RXP/RXP X smo2006-002-016 RXP/RXP X MODELS _______ SAFETY INFORMATION ________...

  • Page 35: Pre-Ride Inspection

    PRE-RIDE INSPECTION The pre-ride inspection is very important prior to operating the watercraft. Always check the proper operation of critical controls, safety features and mechanical components before starting. If not done as specified here, severe injury or death might occur. Bring all safety equipment required by local laws.

  • Page 36: Hull

    PRE-RIDE INSPECTION Hull Inspect hull for cracks or damage. Jet Pump Water Intake Remove weeds, shells, debris or any- thing else that could restrict the flow of water and damage propulsion unit. Clean as necessary. If any obstruction can not be removed, refer to an autho- rized Sea-Doo dealer for servicing TYPICAL —...

  • Page 37: Fuel Tank

    TYPICAL 1. Battery Fuel Tank With the watercraft horizontal, fill the fuel tank to specified level. Check fuel tank retaining straps/ fasteners. Engine Compartment WARNING Should any leak or gasoline odor be present, do not start the engine. Refer to an authorized Sea-Doo dealer before use.

  • Page 38: Variable Trim System (Vts)

    PRE-RIDE INSPECTION dle position. With shift lever in reverse position, gate should be in downward position. WARNING Verify the reverse gate operation before starting the engine. Variable Trim System (VTS) All RXP, RXT-X and WAKE Models Install DESS key then push arrows of VTS button to check nozzle move- ment.

  • Page 39: Vehicle Information

    VEHICLE INFORMATION _______________...

  • Page 40: Controls/Instruments/Equipments

    CONTROLS/INSTRUMENTS/EQUIPMENTS NOTE: Some components do not apply or are optional on some models. smo2008-001-002_b TYPICAL — GTI MODELS smo2008-001-057_a TYPICAL — GTX, RXT, RXP AND WAKE MODELS ______________...
  • Page 41 smo2008-001-005_b TYPICAL — X PACKAGE MODELS smo2008-001-059_a TYPICAL — ALL MODELS EXCEPT X PACKAGE CONTROLS/INSTRUMENTS/EQUIPMENTS _______________...
  • Page 42 CONTROLS/INSTRUMENTS/EQUIPMENTS smo2008-001-060_a TYPICAL — X PACKAGE MODELS smo2008-001-061_a TYPICAL — GTX LIMITED ______________ smo2008-001-062_a TYPICAL — WAKE MODELS...

  • Page 43: Dess Post (Engine Stop Switch)

    smo2008-001-063_a TYPICAL — WAKE MODELS 1. DESS Post (engine cut-off switch) 2. Handlebar 3. Throttle Lever 4. Engine Start/Stop Button 5. Variable Trim System (VTS™) 6. Shift Lever 7. Information Center Gauge 8. Glove Box 9. GPS Receiver (Global Positioning System) 10.

  • Page 44: Handlebar

    CONTROLS/INSTRUMENTS/EQUIPMENTS will occur when the DESS key is left on its post 5 seconds after engine is stopped. Always ensure the DESS key is not left on its post after engine is stopped. IMPORTANT: Leaving the DESS key on its post when engine is not running will slowly discharge the battery.

  • Page 45: Throttle Lever

    WARNING Check handlebar and correspond- ing steering nozzle and side vanes operation before starting. Never turn handlebar while someone is nearby rear of watercraft. Keep away from steering moving parts (nozzle, side vanes, linkage etc.). Adjustment GTX Limited and RXT International Models The handlebar height can be adjusted to suit rider preferences.

  • Page 46: Variable Trim System (Vts)

    CONTROLS/INSTRUMENTS/EQUIPMENTS WARNING Directional control is reduced when the throttle is released or when engine is off. smo2008-001-010_a TYPICAL — ALL MODELS EXCEPT X PACKAGE 1. Engine start/stop button smo2008-001-011_a X PACKAGE ONLY 1. Engine start/stop button Variable Trim System (VTS) RXP, RXP-X, RXT-X and WAKE Models Provides...
  • Page 47 smo2008-001-030_a INFORMATION CENTER GAUGE — VTS POSITION INDICATOR 1. Position indicator 2. Bow up 3. Bow down 4. Operating range (RXP models) 5. Operating range (other models) High Performance VTS RXP-X, RXT-X and WAKE Models Provides pre-set positions for quick settings when adjusting watercraft trim.

  • Page 48: Shift Lever

    CONTROLS/INSTRUMENTS/EQUIPMENTS 6. Adjust trim to the desired position using VTS buttons. 7. Push both VTS buttons again simul- taneously to record trim position. Trim pre-set positions are recorded and ready to be used. To record new settings, repeat proce- dure. Using Pre-Set Trim Positions To set trim to the highest trim position recorded, double-click on VTS upper...
  • Page 49 activated (when the DESS key is in- stalled). This allows the driver to vali- date they are all working properly. WARNING Reading the gauge digital display can distract from the operation of the watercraft, particularly from constantly scanning the environ- ment.
  • Page 50 CONTROLS/INSTRUMENTS/EQUIPMENTS smo2008-001-034_a GTX, RXP, RXT AND WAKE MODELS 1. Information display Compass All Models Except GTI Models Displays the cardinal points to indicate the orientation of the watercraft. smo2008-001-024_a TYPICAL 1. Compass WARNING Use the compass as a guide only. Not to be used for navigation pur- poses.

  • Page 51: Glove Box

    smo2008-001-029_a TYPICAL — UNDER RPM 1. Water depth WARNING Never use the depth gauge as a warning device to ride in shallow water. Use it as a navigation guide only. Not to be used for navigation purposes. 7) Water Temperature Display All Models Except GTI Displays the water temperature of the water surface in degrees Celsius (°C)

  • Page 52: Gps Receiver (Global Positioning System)

    CONTROLS/INSTRUMENTS/EQUIPMENTS smo2006-002-003_a OPEN COVER 1. Glove box cover smo2006-002-004_a PULL ON COVER GPS Receiver (Global Positioning System) GTX Limited Model A removable GPS receiver located on the glove box cover. The GPS receiver provides the water- craft position on earth. Refer to manufacturer's documenta- tion supplied with the GPS receiver for proper use.

  • Page 53: Front Storage Compartment

    TYPICAL To reinstall, position GPS receiver in its receptacle and push until it latches. TYPICAL Front Storage Compartment A convenient watertight area (remov- able on some models) to carry per- sonal articles. Ideal location for an approved fire extinguisher (so ld sep- arately), towrope, first aid kit, etc.
  • Page 54 CONTROLS/INSTRUMENTS/EQUIPMENTS Self-Contained Removable Storage GTI, GTX and Wake Models NOTICE MAXIMUM load is 11 kg (25 lb). Cover Opening Release cover latches then pull on cover handle to open. smo2008-001-067_a GTI MODELS Step 1: Release cover latches Step 2: Open cover smo2008-001-068_a GTX, WAKE MODELS Step 1: Release cover latches...
  • Page 55 smo2008-001-069_b GTI MODELS Step 1: Insert storage bin front tabs Step 2: Push to secure smo2008-001-070_b GTX, WAKE MODELS Step 1: Insert storage bin front tabs Step 2: Push to secure NOTICE Never operate the water- craft without storage bin properly installed, water might enter and fill the bilge.

  • Page 56: Rear Seat Latch

    CONTROLS/INSTRUMENTS/EQUIPMENTS smo2007-002-008_a GTX and Wake Models smo2007-002-004_c RXT Models Use support inside RH auxiliary stor- age compartment. smo2007-002-006_a ______________ RXP Models Lift the storage bin to get access to the holder for an approved fire extin- guisher (sold separately). It also con- tains the Operator’s Guide.

  • Page 57: Seat Latch

    TYPICAL 1. Latch hole 2. Pin Seat Latch Removing the seat allows access to the engine compartment. The seat latch is located at the rear end and underneath the seat. NOTE: On some models, it is neces- sary to remove the rear seat first. smo2008-001-015_a TYPICAL —...

  • Page 58: Rear Storage Basket

    CONTROLS/INSTRUMENTS/EQUIPMENTS WARNING Certain components in the engine compartment may be very hot. Direct contact may result in skin burn. When starting or operating the engine, do not touch any elec- trical part. Never leave any object, rag, tool, etc., in the engine com- partment or in the bilge.

  • Page 59: Mooring Cleats

    smo2008-001-017_a GTI SE AND GTX MODELS 1. Eyelet smo2008-001-018_a ALL MODELS EXCEPT GTI 1. Eyelets Mooring Cleats These cleats can be temporarily used for docking, while refueling for exam- ple. TYPICAL — ALL MODELS EXCEPT X PACKAGE 1. Mooring cleats NOTICE Never use mooring cleats to pull or lift the watercraft.

  • Page 60: Ski/Wakeboard Post

    CONTROLS/INSTRUMENTS/EQUIPMENTS NOTICE Remove watercraft from water prior to unscrewing drain plugs. TYPICAL 1. Drain plugs 2. Tighten 3. Unscrew NOTICE Make sure drain plugs are properly secured prior to launching the watercraft in water. Ski/Wakeboard Post WAKE Models Pull up the post to hook up a ski or wakeboard rope.

  • Page 61: Wakeboard Rack

    NOTICE Never wakeboard post to tow other crafts. Respect the maximum load limit rat- ing of the ski/wakeboard post. Over- loading can affect maneuverability, stability and performance. Wakeboard Rack WAKE Models Convenient removable rack to carry a wakeboard. To install: NOTE: Wakeboard rack can be in- stalled on both sides of watercraft.
  • Page 62 CONTROLS/INSTRUMENTS/EQUIPMENTS 6. When installing a wakeboard on the rack, position wakeboard fin(s) out- ward then secure bungee cords to tightly hold wakeboard. WARNING To avoid possible injuries and cuts from wakeboard's fin(s), always place FIN(S) OUTWARDS. 1. Fin outward 7. After installation, pull and push wakeboard to ensure it is tightly secured to rack.

  • Page 63: Recessed Cargo Cleats

    NOTICE The rack is designed to hold one wakeboard. Do not use to hold more than one wakeboard or to transport ski or any other object. Do not use rack(s) as mooring points or to reboard. WARNING With wakeboard and/or rack in- stalled, operate with extra caution: –...
  • Page 64 CONTROLS/INSTRUMENTS/EQUIPMENTS smo2008-001-021_a TYPICAL — BALLAST SYSTEM 1. Port side tank 2. Starboard side tank 3. Front supports 4. Rear clamps 5. Valves 6. Drain plugs 7. Overflow holes 8. Propulsion system connections Installation WARNING NEVER install only one ballast tank, uneven added weight of the ballast could affect the handling characteristics of the watercraft.
  • Page 65 smo2008-001-047_a TYPICAL 1. Propulsion system connections Proceed with the installation of the other ballast tank. Then, ballast tanks are ready to be filled. To Fill Ballasts are filled by jet pump pressure. Watercraft will need to move forward in order to fill the ballasts. WARNING NEVER fill only one ballast tank, uneven added weight of the bal-...
  • Page 66 CONTROLS/INSTRUMENTS/EQUIPMENTS To Empty NOTE: It is recommended to empty ballast tanks after each use. Always completely empty the tanks water back to the same lake it came from, do not transfer. To empty ballast tanks – Unscrew drain plugs and flush wa- ter.

  • Page 67: Operating Instructions

    OPERATING INSTRUCTIONS WARNING Always perform OPERATION CHECKS operating the watercraft. Become thoroughly familiar with all con- trols and the function of each. Should any control or instruction not be fully understood, refer to an authorized Sea-Doo dealer. Principle of Operation Propulsion The engine is directly coupled to a drive shaft which, in turn, rotates an...
  • Page 68 OPERATING INSTRUCTIONS Neutral and Reverse WARNING Never use jet pump components as a supporting point to board the watercraft. Shift lever should only be used when the engine is idling and watercraft is completely stopped. Never rev the engine at high RPM in reverse. Do not use reverse to stop the watercraft.
  • Page 69 TYPICAL 1. Reverse gate in downward position NOTE: To obtain maximum efficiency and control from the reverse, increase engine speed to slightly above idle. Too much RPM will create water turbu- lence and reduce reverse efficiency. In reverse position, turn the handlebar in the same direction that you want to move the rear of the watercraft.
  • Page 70 OPERATING INSTRUCTIONS smo2008-001-022_a TYPICAL 1. Push on arrow pointing upward on VTS button 2. Bow up 3. Nozzle up 4. VTS position When the nozzle is directed down- ward, the bow is forced downward and enhances the watercraft turning capabilities. As with any watercraft, speed and operator body position and movement (body English), will deter- mine the degree and sharpness of the...
  • Page 71 duce speed and avoid sharp turns. Avoid choppy water conditions when carrying a passenger. NOTICE Combustion engine needs air to operate; consequently this watercraft watertight. Any maneuvers such as figure eights etc., that cause the upper deck to be under water may cause severe engine...

  • Page 72: Boarding The Watercraft

    OPERATING INSTRUCTIONS WARNING Check handlebar and correspond- ing side vanes operation before starting. Never use side vanes as a supporting point to board the watercraft or to lift it. Never turn handlebar while someone is nearby rear of watercraft. Keep away from steering moving parts (nozzle, side vanes, linkage etc.).
  • Page 73 A. Maintain at least 90 cm (3 ft) underneath the lowest rear portion of the hull when all passengers are aboard Boarding in Deep Water Operator Alone Swim to the rear of the watercraft. Grab the grab handle and pull yourself upward until your knee can reach the boarding platform then grip the seat strap.

  • Page 74: Starting

    OPERATING INSTRUCTIONS Starting Preparation Before unloading the watercraft from the trailer, it can be started for about 10 seconds to verify proper operation. WARNING Certain components in the engine compartment may be very hot. Direct contact may result in skin burn.

  • Page 75: Rear Grab Handle

    NOTICE Avoid watercraft opera- tion in weeded areas. If unavoid- able, vary watercraft speed. Air Intake Opening This is where air enters to supply the engine and to ventilate the engine compartment. If the air intake open- ing is kept under water, water will get inside bilge.

  • Page 76: Operation With Wakeboard Rack And Ballast Tanks

    OPERATING INSTRUCTIONS Operation with Wakeboard Rack and Ballast Tanks WAKE Models WARNING Operate with extra caution: – NEVER perform aggressive ma- neuvers including spin-out. – NEVER jump waves. – Use common sense and limit speed. Otherwise, wakeboard or tanks could detach or occupants could fall off and get injured against the wakeboard, rack or tanks.

  • Page 77: Shutting Off The Engine

    NOTICE Pay attention, when leav- ing the watercraft on the beach, so that the side vanes do not rub or hit the ground due to the rocking move- ment. It might eventually damage components of the O.P.A.S. system. Shutting Off the Engine To keep watercraft directional control, the engine should be running until the watercraft is at idle.
  • Page 78 OPERATING INSTRUCTIONS Exhaust System Flushing NOTE: Including intercooler on super- charged models. General Flushing the exhaust system and in- tercooler (supercharged models) with fresh water is essential to neutralize corroding effects of salt or other chem- ical products present in water. It will help to remove sand, salt, shells or other particles in water jackets and/or hoses.
  • Page 79 NOTICE Never run engine longer than 5 minutes. Drive line seal has no cooling when watercraft is out of water. Close the water tap, then stop the en- gine. NOTICE Always close the water tap before stopping the engine. NOTICE Remove quick connect adapter after flushing operation (if used).

  • Page 80: Special Procedures

    SPECIAL PROCEDURES Jet Pump Water Intake and Impeller Cleaning WARNING Keep away from intake grate while engine is on. Items such as long hair, loose clothing or personal flotation device straps can become entangled in moving parts result- ing in severe injury or drowning. Weeds, shells or debris can get caught on the intake grate, drive shaft and/or impeller.

  • Page 81: Capsized Watercraft

    Capsized Watercraft The watercraft is designed so that it should not turn over easily. Also two sponsons mounted on the side of the hull assist watercraft stability. If it turns over, it will remain capsized. WARNING When watercraft is capsized, do not attempt to restart the engine.
  • Page 82 SPECIAL PROCEDURES When towing your watercraft in wa- ter, pinch the water supply hose from the exhaust manifold to muffler with a large hose pincher (P/N 529 032 500). F01B23Y This will prevent the exhaust system from filling which may lead to water be- ing injected into and filling the engine.

  • Page 83: Maintenance Information

    MAINTENANCE INFORMATION _______________...

  • Page 84: Maintenance Schedule

    MAINTENANCE SCHEDULE Maintenance is very important for keeping your watercraft in safe op- erating condition. Proper maintenance is the owner's responsibility. Perform periodic checks and follow the mainte- nance schedule. WARNING Failure to properly maintain the watercraft according to the main- tenance schedule and procedures can make it unsafe to operate.
  • Page 85 A: Adjust C: Clean I: Inspect L: Lubricate R: Replace O: Operator D: Dealer PART/TASK ENGINE Engine oil and filter Rubber mounts Corrosion protection EXHAUST SYSTEM Exhaust system Supercharger clutch COOLING SYSTEM Hose and fasteners Coolant FUEL SYSTEM Throttle cable Fuel cap, filler neck, fuel tank, fuel tank straps, fuel lines and connections Fuel system leak test...
  • Page 86 MAINTENANCE SCHEDULE A: Adjust C: Clean I: Inspect L: Lubricate R: Replace O: Operator D: Dealer PART/TASK ELECTRICAL SYSTEM Spark plug Electrical connections and fastening (ignition system, starting system, fuel injectors etc.) DESS key/post Monitoring beeper Battery and fasteners (9) STEERING SYSTEM Steering cable and connections Steering nozzle bushings...
  • Page 87 A: Adjust C: Clean I: Inspect L: Lubricate R: Replace O: Operator D: Dealer PART/TASK HULL AND BODY Hull Ski/wakeboard post and fasteners Ride plate and water intake grate NOTE 1: The supercharger clutch requires replacement when the “MAINTENANCE SUPER- CHARGER”...

  • Page 88: 10-Hour Inspection

    10-HOUR INSPECTION We suggest that after the first 10 hours of operation, the boat be checked by an au- thorized Sea-Doo Watercrafts dealer. The initial maintenance is very important and must not be neglected. NOTE: The 10-hour inspection is at the expense of the PWC owner. We recommend that this inspection be signed by an authorized Sea-Doo Water- crafts dealer.

  • Page 89: Maintenance Procedures

    MAINTENANCE PROCEDURES Engine Oil Recommended Engine Oil Use XP-S SUMMER GRADE OIL (P/N 293 600 121). 130 and 155 Engines If the XP-S engine oil is not available, use a 5W 40 engine oil meeting the requirements for API service classifi- cation SM, SL or SJ.

  • Page 90: Engine Coolant

    MAINTENANCE PROCEDURES 5. Reinstall dipstick, push in com- pletely. 6. Remove dipstick again and read oil level. It should be between marks. lmr2007-053-100_a 1. Full 2. Add 3. Operating range 7. Add oil up to have the level between marks as required. To add oil: –...

  • Page 91: Throttle Body

    WARNING Certain components in the engine compartment may be very hot. Direct contact may result in skin burn. Remove seat(s) to expose cooling sys- tem expansion tank. smo2007-002-005_c TYPICAL 1. Expansion tank 2. Cap With vehicle on a level surface, liquid should be between MIN.

  • Page 92: Throttle Cable

    MAINTENANCE PROCEDURES smo2008-001-052_a TYPICAL — ALL MODELS EXCEPT GTI 1. Fitting Throttle Cable Throttle Cable Inspection Depress and release throttle lever or finger throttle. It should operate smoothly and return to its initial po- sition without any hesitation. There must be a small amount of free-play when released.
  • Page 93 1. Fuse 2. Check if melted 3. Ampere rating WARNING Do not use a higher rated fuse as this can cause severe damage. If a fuse has burnt out, source of mal- function should be determined and corrected before restarting. See an authorized Sea-Doo dealer for servicing.

  • Page 94: Ride Plate And Water Intake Grate

    MAINTENANCE PROCEDURES Ride Plate and Water Intake Grate Ride Plate and Water Intake Grate Inspection Inspect ride plate and jet pump water intake grate for damage. Have dam- aged parts repaired. WARNING The DESS key should always be removed from its post prior to in- specting the intake grate.

  • Page 95: Storage And Preseason Preparation

    STORAGE AND PRESEASON PREPARATION Storage WARNING Because fuel flammable, have an authorized Sea-Doo dealer inspect the fuel system integrity as specified in the periodic inspection chart. It is recommended that the watercraft be serviced by an authorized Sea-Doo dealer for storage but the following op- erations can be performed by you with a minimum of tools.
  • Page 96 STORAGE AND PRESEASON PREPARATION sbs2008-005-001_a 1. Intake hose (from intercooler) 2. Throttle body 2. Start and rev up the engine to 4000 RPMs several times. sbs2008-005-002 WATER EXPELLED FROM INTERCOOLER 3. Stop engine. 4. Liberally lubricate throttle body in- side and out. 5.
  • Page 97 smo2008-001-054_a 1. Flushing connector — location may differ The following hose can be fabricated to ease draining procedure. smo2008-001-053_a TYPICAL 1. Flushing connector adapter 2. Hose 12.7 mm (1/2 in) 3. Air hose male adapter NOTICE Failure to drain the ex- haust system may cause severe damage to the intercooler (super- charged models) and exhaust mani-...
  • Page 98 STORAGE AND PRESEASON PREPARATION Reinstall ignition coils. Reconnect igni- tion coil connectors. To reinstall engine cover, push it down- ward until it snaps. Wipe up any residual water from the engine. Disconnect the garden hose. NOTE: It is recommended to fog the engine valves with XP-S Lube.

  • Page 99: Preseason Preparation

    If the watercraft is to be stored outside, cover it with an opaque tarpaulin to pre- vent sun rays and grime from affecting the plastic components, watercraft fin- ish as well as preventing dust accumu- lation. NOTICE watercraft never be left in water for storage. Never leave the watercraft stored in direct sunlight.
  • Page 100 STORAGE AND PRESEASON PREPARATION ______________...

  • Page 101: Technical Information

    TECHNICAL INFORMATION _______________...

  • Page 102: Identification Numbers

    IDENTIFICATION NUMBERS The main components of the water- craft (engine and hull) are identified by different serial numbers. It may some- times become necessary to locate these numbers for warranty purposes or to trace the watercraft in the event of theft. Hull The Hull Identification Number (H.I.N.) is located on footboard at the rear of...

  • Page 103: Engine Emissions Information

    ENGINE EMISSIONS INFORMATION NOTE: Maintenance, replacement, or repair of the emission control devices and systems may be performed by any marine SI (spark ignition) engine repair establishments or individual. Manufacturer's Responsibility Beginning with 1999 model year en- gines, PWC manufacturers of marine engines must determine the exhaust emission levels for each engine horse- power family and certify these engines...

  • Page 104: Specifications

    SPECIFICATIONS VEHICLE ENGINE Type Number of cylinder Number of valve Displacement Intake system Bore Stroke Compression ratio Cooling ELECTRICAL SYSTEM Ignition Starter Battery Spark plug PROPULSION Propulsion system Jet pump Impeller Transmission ______________ WAKE 155 Rotax 12 valves (4 per cylinder) with hydraulic Type Naturally aspirated Throttle body...
  • Page 105 VEHICLE DIMENSION AND WEIGHT Length Width Height Weight (dry) LOADING CAPACITY Rider capacity (refer to load limit) Storage capacity Load limit (passengers + luggage) FLUIDS Fuel Engine oil Cooling system WAKE 155 382 kg (840 lb) Type Inside North America: (87 (RON + MON)/2) Minimum octane Outside North America: 92 RON...
  • Page 106 SPECIFICATIONS VEHICLE ENGINE Type Number of cylinder Number of valve Displacement Type Intake system Throttle body Bore Stroke Compression ratio Cooling ELECTRICAL SYSTEM Ignition Starter Battery Make and type Spark plug PROPULSION Propulsion system Type Jet pump Material Impeller Transmission Type Type ______________...
  • Page 107 VEHICLE DIMENSION AND WEIGHT Length Width Height Weight (dry) LOADING CAPACITY Rider capacity (refer to load limit) Storage capacity Load limit (passengers + luggage) FLUIDS Type Minimum octane Fuel Recommended octane rating for optimum performance Tank capacity Type Engine oil Capacity Coolant type Cooling system...
  • Page 108 SPECIFICATIONS VEHICLE ENGINE Type Number of cylinder Number of valve Displacement Type Intake system Throttle body Bore Stroke Compression ratio Cooling ELECTRICAL SYSTEM Ignition Starter Battery Make and type Spark plug PROPULSION Propulsion system Type Jet pump Material Impeller Transmission Type Type ______________...
  • Page 109 VEHICLE DIMENSION AND WEIGHT Length Width Height Weight (dry) LOADING CAPACITY Rider capacity (refer to load limit) Storage capacity Load limit (passengers + luggage) FLUIDS Type Minimum octane Fuel Recommended octane rating for optimum performance Tank capacity Type Engine oil Capacity Coolant type Cooling system...
  • Page 110 SPECIFICATIONS VEHICLE ENGINE Type Number of cylinder Number of valve Displacement Intake system Bore Stroke Compression ratio Cooling ELECTRICAL SYSTEM Ignition Starter Battery Spark plug PROPULSION Propulsion system Jet pump Impeller Transmission ______________ GTX 155 Rotax 12 valves (4 per cylinder) with hydraulic Type Naturally aspirated Throttle body...
  • Page 111 VEHICLE DIMENSION AND WEIGHT Length Width Height Weight (dry) LOADING CAPACITY Rider capacity (refer to load limit) Storage capacity Load limit (passengers + luggage) FLUIDS Fuel Engine oil Cooling system NOTE: BRP reserves the right to make changes in design and specifications and/or to make additions to, or improvements in its products without imposing any obligation upon itself to install them on its products previously manufactured.
  • Page 112 SPECIFICATIONS VEHICLE ENGINE Type Number of cylinder Number of valve Displacement Type Intake system Throttle body Bore Stroke Compression ratio Cooling ELECTRICAL SYSTEM Ignition Starter Battery Make and type Spark plug PROPULSION Propulsion system Type Jet pump Material Impeller Transmission ______________ GTI MODELS GTI 130...
  • Page 113 VEHICLE DIMENSION AND WEIGHT Length Width Height Weight (dry) LOADING CAPACITY Rider capacity (refer to load limit) Storage capacity Load limit (passengers + luggage) FLUIDS Type Minimum Fuel octane Tank capacity Type Engine oil Capacity Coolant type Cooling system Capacity GTI MODELS GTI 130 GTI SE 130...
  • Page 114 SPECIFICATIONS ______________...

  • Page 115: Troubleshooting

    TROUBLESHOOTING ______________...

  • Page 116: Technical Guidelines

    TECHNICAL GUIDELINES ENGINE WILL NOT START 1. DESS key removed. – Install DESS key over post. 2. ECM does not recognize the DESS key. – Refer to an authorized Sea-Doo dealer. 3. Burnt fuse: main, electric starter or ECM. – Check wiring then replace fuse(s). 4.
  • Page 117 ENGINE TURNS NORMALLY BUT WILL NOT START (cont’d) 5. Engine management system fault detected (check engine pilot lamp is ON). – Refer to an authorized Sea-Doo dealer. 6. Faulty fuel pump. – Refer to an authorized Sea-Doo dealer. ENGINE MISFIRES, RUNS IRREGULARLY 1.
  • Page 118 TECHNICAL GUIDELINES ENGINE LACKS ACCELERATION OR POWER (cont’d) 3. Engine management system fault detected (check engine pilot lamp is ON). – Refer to MONITORING SYSTEM in SPECIAL PROCEDURES. 4. Clogged injectors. – Refer to an authorized Sea-Doo dealer. 5. Low fuel pressure. –...
  • Page 119 O.P.A.S. SYSTEM FAULTS (MODELS WITH SLIDING VANES) (cont’d) 4. O.P.A.S. side vanes do not go down while engine is at idle. – Broken spring inside side vane cylinder. Refer to an authorized Sea-Doo dealer. ABNORMAL NOISE FROM PROPULSION SYSTEM 1. Weeds or debris jammed around impeller. –...

  • Page 120: Monitoring System

    MONITORING SYSTEM A system monitors the electronic com- ponents of the EMS (engine man- agement system) and other compo- nents of the electrical system. When a fault occurs, it sends visual messages through the information center and/or audible signals through a beeper to in- form you of a particular condition.

  • Page 121: Beeper Code Information

    PILOT MESSAGE DISPLAY LAMPS (ON) MAINTENANCE SUPERCHARGER SENSOR L KEY NOTICE Running engine with low oil pressure may severely damage the engine. Beeper Code Information BEEPER CODES 1 Long Beep (while installing DESS key on watercraft post) 1 Short Beep followed by 1 long beep 4 Short Beeps at different interval for...
  • Page 122 MONITORING SYSTEM BEEPER CODES A 2 Seconds Beep every 5 minutes interval Continuously Beeps NOTICE If the monitoring beeper continuously sounds, stop engine as soon as possible. ______________ DESCRIPTION Low fuel level. Refill fuel tank. If problem persists, refer to an authorized Sea-Doo dealer.

  • Page 123: Warranty

    WARRANTY ______________...

  • Page 124: Brp Limited Warranty - Usa And Canada: 2009 Sea-Doo

    BRP LIMITED WARRANTY – USA AND CANADA: 2009 SEA-DOO 1. SCOPE Bombardier Recreational Products Inc. (“BRP”)* warrants its model-year 2009 Sea-Doo personal watercraft sold by authorized Sea-Doo Dealers (as defined below) in the fifty United States and in Canada from defects in material or work- manship for the period and under the conditions described below.
  • Page 125 – Damage resulting from removal of parts, improper repairs, service, mainte- nance, modifications or use of parts not manufactured or approved by BRP or resulting from repairs done by a person that is not an authorized servicing BRP dealer; – Damage caused by abuse, abnormal use, neglect, or operation of the product in a manner inconsistent with the recommended operation described in the Oper- ator’s Guide;...
  • Page 126 5. CONDITIONS TO HAVE WARRANTY COVERAGE This warranty coverage is available only if each of the following conditions has been fulfilled: – The 2009 Sea-Doo personal watercraft must be purchased as new and unused by its first owner from a BRP dealer authorized to distribute Sea-Doo personal watercraft in the country in which the sale occurred (“BRP dealer”);...
  • Page 127 8. TRANSFER If the ownership of a product is transferred during the warranty coverage period, this warranty shall also be transferred and be valid for the remaining coverage period provided that BRP is notified of such transfer of ownership in the following way: 1.

  • Page 128: With 4-Tec ® Engines

    CALIFORNIA AND NEW YORK EMISSION CONTROL WARRANTY STATEMENT FOR MODEL YEAR 2009 ® ® SEA-DOO PERSONAL WATERCRAFT WITH 4-TEC ENGINES For California, your Sea-Doo personal watercraft has a special environmental label required by the California Air Resources Board. The label has 1, 2, 3 or 4 stars. A hangtag, provided with your personal watercraft, describes the meaning of the star rating system.
  • Page 129 Three Stars – Ultra Low Emission The three-star label identifies engines that meet the Air Resources Board’s Per- sonal Watercraft and Outboard marine engine 2008 exhaust emission standards or the Stern drive and Inboard marine engine 2003 exhaust emission standards. Engines meeting these standards have 65% lower emissions than One Star –...
  • Page 130 Parts covered for a model year 2009 Sea-Doo personal watercraft equipped with 4-TEC ® engines: Digital linear actuator (low idle control) Throttle position sensor Intake manifold air temperature sensor Intake manifold air pressure sensor Engine temperature sensor Knock sensor Emission control unit Injectors Fuel pressure regulator Intake manifold...
  • Page 131 Owner’s Warranty Responsibilities As the personal watercraft owner, you are responsible for the performance of the required maintenance listed in your Operator’s Guide. BRP recommends that you retain all receipts covering maintenance on your personal watercraft engine, but BRP cannot deny warranty solely for the lack of receipts or your failure to ensure the performance of all scheduled maintenance.
  • Page 132 BRP INTERNATIONAL LIMITED WARRANTY: 2009 ® SEA-DOO PERSONAL WATERCRAFT 1. SCOPE Bombardier Recreational Products Inc. (“BRP”)* warrants its model year 2009 Sea-Doo personal watercraft sold by authorized BRP distributors/dealers (defined below) outside of the fifty United States, Canada and states members of the European Economic Area (which is comprised of the states member of the Eu- ropean Union plus Norway, Iceland and Liechtenstein), will be free from defects in material or workmanship for the period and under the conditions described...
  • Page 133 – Damage caused by abuse, abnormal use, neglect or operation of the product in a manner inconsistent with the recommended operation described in the Oper- ator’s Guide; – Damage resulting from accident, submersion, fire, theft, vandalism or any act of God;...
  • Page 134 6. WHAT TO DO TO OBTAIN WARRANTY COVERAGE The customer must cease using the Sea-Doo personal watercraft upon the appear- ance of an anomaly. The customer must notify a servicing BRP distributor/dealer within two (2) days of the appearance of a defect, and provide it with reasonable access to the product and reasonable opportunity to repair it.
  • Page 135 For countries within Europe, Middle East, Africa, Russia & CIS, please contact our European office: BRP EUROPE N.V. Consumer Assistance Center Skaldenstraat 125 9042 Gent Belgium Tel.: + 32-9-218-26-00 For Scandinavian countries, please contact our Finland office: BRP FINLAND OY Service Department Ahjotie 30 Fin-96320 Rovaniemi...

  • Page 136: Personal

    BRP LIMITED WARRANTY FOR THE EUROPEAN ECONOMIC AREA: 2009 SEA-DOO WATERCRAFT 1. SCOPE OF THE LIMITED WARRANTY Bombardier Recreational Product Inc. (“BRP”)* warrants its model year 2009 Sea-Doo ® personal watercraft sold by authorized BRP ("Distributors/Dealers") in member states of the European Economic Area ("EEA") (which is comprised of the states member of the European Union plus Norway, Iceland and Liechtenstein) from defects in material or workmanship for the period and under the conditions described below.
  • Page 137 – Damage caused by abuse, abnormal use, neglect or operation of the product in a manner inconsistent with the recommended operation described in the Oper- ator’s Guide; – Damage resulting from accident, submersion, fire, theft, vandalism or any act of God;...
  • Page 138 BRP will not honor this limited warranty to any private use owner or commercial use owner if the preceding conditions have not been met. Such limitations are necessary in order to allow BRP to preserve both the safety of its products, and also that of its consumers and the general public.
  • Page 139 3. If the matter still remains unresolved then contact BRP at the address listed be- low. For countries within Europe, Middle East, Africa, Russia & CIS, please contact our European office: BRP EUROPE N.V. Consumer Assistance Center Skaldenstraat 125 9042 Gent Belgium Tel.: + 32-9-218-26-00 For Scandinavian countries, please contact our Finland office:...

  • Page 140: Privacy Information/Disclaimer

    PRIVACY INFORMATION/DISCLAIMER We wish to inform you that your coordinates will be used for safety and warranty purposes. Sometimes, we also use the coordinates of our clients to inform them about our products and to present them offers. Should you prefer not to receive in- formation on our products, services and offers, please let us know by writing to the address below.

  • Page 141: Change Of Address/Ownership

    CHANGE OF ADDRESS/OWNERSHIP If your address has changed or if you are the new owner of the boat, be sure to no- tify BRP by either: – mailing one of the following card below; – North America Only: calling at 715 848-4957 (USA) or 819 566-3366 (Canada); –...
  • Page 142 ______________...
  • Page 143 ______________...
  • Page 144 ______________...
  • Page 145 ______________...
  • Page 146 ______________...

This manual is also suitable for:

Gti seriesRxp seriesRxt seriesWake series2009 sea-doo gtx series2009 sea-doo gti series ... Show all

Table of Contents