Advertisement
Quick Links
Installation and Use Manual
EMASMB & LMASMB Surface Mount Bottle Filling Stations
Installer
To assure you install this model easily and correctly, PLEASE READ THESE
SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK
YOUR INSTALLATION FOR COMPLIANCE WITH ALL PLUMBING, ELECTRICAL
AND OTHER APPLICABLE CODES. FOLLOW ALL WARNINGS AND CAUTIONS
CAREFULLY. After installation, leave these instructions with the customer for future
reference.
Warnings
1. Use with clean, clear, fresh potable drinking water only! Do not use with water that is microbiologically
unsafe or of unknown quality without adequate disinfection before the system.
2.
These products are designed to operate on 20 to 105 PSI (0.14-0.72 MPa) supply line pressure and a
maximum water temperature of 90°F (32°C). If inlet pressure is above 105 PSI (0.72 MPa), a pressure
regulator must be installed in supply line. Any damage caused by reason of connecting this product to
supply line pressure lower than 20 PSI or higher than 105 PSI is not covered by warranty
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use
of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children without supervision.
EMASMB*A & LMASMB*A
Model
EMASMB
Page 1
IMPORTANT
THIS IS AN INDOOR APPLICATION ONLY!
ALL SERVICE TO BE PERFORMED BY AN
AUTHORIZED SERVICE PERSONNEL.
TOOLS/ITEMS REQUIRED
BUT NOT SUPPLIED
- SERVICE STOP VALVE WITH 3/8"
COMPRESSION OUTLET
- FASTENERS FOR WALL TYPE (8 REQ'D.)
- SLIP JOINT DRAIN UNION OR
COMPRESSION CLAMP
- 5/32" HEX-WRENCH
.
1000002042 (Rev. F - 08/17)
Advertisement
Related Manuals for Elkay EMASMB
Summary of Contents for Elkay EMASMB
- Page 1 EMASMB*A & LMASMB*A Installation and Use Manual EMASMB & LMASMB Surface Mount Bottle Filling Stations IMPORTANT THIS IS AN INDOOR APPLICATION ONLY! ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSONNEL. TOOLS/ITEMS REQUIRED BUT NOT SUPPLIED - SERVICE STOP VALVE WITH 3/8"...
-
Page 2: Installation Notes
C =7/16" X 3/4" OBROUND MOUNTING HOLES FOR FASTENING BACKPLATE TO WALL. Pre-Installation (reference Rough-Ins, Fig. 1 and Fig. 2) 1. Ensure Wall is structurally sound to bear the loads imparted by the EMASMB or LMASMB Bottle Filler (On-Wall Bottle Filler). If necessary, install a Wall Support Carrier (not supplied). - Page 3 C =7/16" X 3/4" OBROUND MOUNTING HOLES FOR FASTENING BACKPLATE TO WALL. Pre-Installation (reference Rough-Ins, Fig. 1 and Fig. 2) 1. Ensure Wall is structurally sound to bear the loads imparted by the EMASMB or LMASMB Bottle Filler (On-Wall Bottle Filler). If necessary, install a Wall Support Carrier (not supplied).
-
Page 4: Installation Instructions
EMASMB*A & LMASMB*A INSTALLATION INSTRUCTIONS Ensure packaging contains the following components EMASMB UNIT SHOWN TOP COVER SCREWS TOP COVER BACK PANEL OUTER WRAPPER REGULATOR ASSEMBLY PLUMBING DIAGRAM BATTERY TRAY NON-FILTERED INSTALLER TO SUPPLY: SHUT OFF VALVE BOTTOM COVER REAR VIEW... - Page 5 EMASMB*A & LMASMB*A INSTALLATION INSTRUCTIONS reference Rough-Ins, Fig. 1 and Fig. 2 Wall Mounting ( 1. Remove Top Cover from Bottle Filler by removing two (2) screws from bottom of unit. Use a 5/32" hex wrench (not supplied). 2. Remove Bottom Cover from Bottle Filler by removing two (2) screws from bottom of unit. Use a 5/32" hex wrench (not supplied).
-
Page 6: Replacement Parts
REPLACEMENT FILTER REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640 FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.834.4816 ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484 • www.elkay.com 1000002042 (Rev. F - 08/17) Page 6...