Washing The Brush Bars; Blockages–Automatic Cut-Out; Washing The Filter Unit; Charging And Storing - Dyson Cyclone V10 Operating Manual

WASHING THE BRUSH BARS

Your appliance has two washable brush bars, check and wash these regularly
according to the following instructions to maintain performance.
• Ensure that the appliance is disconnected from the charger before removing the
brush bar. Be careful not to pull the 'ON' trigger.
To remove, wash and replace brush bars:
• Please refer to the 'Washing the brush bars' illustrations alongside the
instructions below.
• Turn the cleaner head upside down so that the underside of the cleaner head is
facing you. Use a coin to turn the fastener one quarter anticlockwise until it clicks
into the unlocked position.
• Rotate the end cap to the open position. Gently slide the large brush bar away from
the cleaner head.
• Remove the end cap from the large brush bar. Do not wash the end cap.
• Lift out the small brush bar from the octagonal end and pull away from the
cleaner head.
• Hold the brush bars under running water and gently rub to remove any lint or dirt.
• Stand both brush bars upright. Ensure that the large brush bar is stood upright as
shown. Leave to dry completely for a minimum of 24 hours.
• Before replacing, check that the brush bars are completely dry. Refit the small brush
bar before the large one. Insert the round end of the small brush bar into place.
Push down the octagonal end until it clicks into place.
• Reattach the end cap to the brush bar.
• Slide the large brush bar back on to the cleaner head, around the motor. The end
cap should be in the open position as shown. Once in place, rotate the end cap
back into the closed position.
• Close the fastener by turning a quarter turn clockwise. Ensure that the fastener is
fully turned and the base plate and the brush bars are secure.

WASHING THE FILTER UNIT

Check and wash the filter unit, according to the instructions, to
maintain performance.
• Remove the filter unit by twisting counterclockwise to the open position. Gently pull
away from the appliance.
• Wash the inside of the filter unit first; hold it upright under the cold water tap and
agitate using a rotating motion.
• Wash the outside of the filter unit; fill the unit with cold water, place your hand over
the open end and shake gently.
• Repeat washing the inside and outside of the filter unit until the water runs clear.
• Gently tap the filter unit to remove any excess water and leave to dry with the open
end facing up.
• Leave the filter unit to dry completely for a minimum of 24 hours.
• Check that the filter unit is completely dry.
• To refit, return the filter unit to the open position and twist clockwise until it clicks
into place.
The filter unit may require more frequent washing if vacuuming fine dust or using
mainly maximum suction.
Do not put the filter unit in a dishwasher, washing machine, tumble dryer, oven,
microwave or near a naked flame.
BLOCKAGES – AUTOMATIC CUT-OUT
• This appliance is fitted with an automatic cut-out.
• If any part becomes blocked the appliance may automatically cut out.
• This will happen after the motor pulses a number of times (i.e switches on and off in
quick succession) and the blockage indicator LED will illuminate.
• Leave to cool down before looking for blockages.
• Ensure that the appliance is disconnected from the charger before looking for
blockages. Failure to do so could result in personal injury. Clear any blockage
before restarting.
• Refit all parts securely before using.
• Clearing blockages is not covered by your warranty.
LOOKING FOR BLOCKAGES
The motor will pulse and the blockage indicator LED will illuminate when there is a
blockage. Please follow the instructions below to locate the blockage:
• Ensure that the appliance is disconnected from the charger before looking for
blockages. Be careful not to pull the 'ON' trigger.
• Do not operate while checking for blockages as doing so could result in
personal injury.
• Leave to cool down before looking for blockages.
• Beware of sharp objects when checking for blockages.
• To check for blockages in the main body of the appliance, remove the clear
bin following the instructions in the 'Cleaning the clear bin' section and remove
the blockage.
• If you cannot clear an obstruction you may need to remove the brush bars, please
follow the instructions below:
– To remove the soft roller cleaner head brush bars, please refer to the 'Washing
the soft roller cleaner head brush bars' section. Remove the obstruction and
replace the brush bars as shown in the 'Washing the soft roller cleaner head
brush bars' section. Ensure that the fastener is fully turned and the base plate
and brush bars are secure before operating the appliance.
– To remove the brush bar from the direct drive cleaner head or mini motorized
tool, use a coin to unlock the fastener and slide the brush bar out of the
cleaner head. Remove the obstruction. Replace the brush bar and secure it
by tightening the fastener. Ensure that it is fixed firmly before operating the
appliance.
• This appliance has carbon fibre brushes. Take care if coming into contact with
them, as they may cause minor skin irritation. Wash your hands after handling
the brushes.
• Refit all parts securely before using.
• Clearing blockages is not covered by your warranty.

CHARGING AND STORING

• This appliance will switch 'OFF' if the battery temperature is below 3°C
(37.4°F). This is designed to protect the motor and battery. Do not charge the
appliance and then move it to an area with a temperature below 3˚C (37.4°F) for
storage purposes.
• To help prolong battery life, avoid recharging immediately after a full discharge.
Allow to cool for a few minutes.
• Avoid using the appliance with the battery flush to a surface. This will help it run
cooler and prolong battery run time and life.
BATTERY SAFETY INSTRUCTIONS
• If the battery needs replacing please contact the Dyson Helpline.
• Use only Dyson chargers for charging this Dyson appliance.
• The battery is a sealed unit and under normal circumstances poses no safety
concerns. In the unlikely event that liquid leaks from the battery do not touch the
liquid and observe the following precautions:
– Skin contact – can cause irritation. Wash with soap and water.
– Inhalation – can cause respiratory irritation. Expose to fresh air and seek
medical advice.
– Eye contact – can cause irritation. Immediately flush eyes thoroughly with water
for at least 15 minutes. Seek medical attention.
– Disposal – wear gloves to handle the battery and dispose of immediately,
following local ordinances or regulations.
CAUTION
The battery used in this device may present a risk of fire or chemical burn if
mistreated. Do not disassemble, short contacts, heat above 60°C (140°F), or
incinerate. Keep away from children. Do not disassemble and do not dispose of
in fire.
ONLINE SUPPORT
• For online help, general tips, videos and useful information about Dyson.
www.dysoncanada.ca/support

DISPOSAL INFORMATION

• Dyson products are made from high grade recyclable materials. Recycle
where possible.
• The battery should be removed from the product before disposal.
• Dispose of the battery in accordance with local ordinances or regulations.
• Dispose of the exhausted filter unit in accordance with local ordinances
or regulations.
DYSON CUSTOMER CARE
THANK YOU FOR CHOOSING TO BUY A DYSON APPLIANCE
After registering your free 2 year warranty, your Dyson appliance will be covered
for parts and labour for 2 years from the date of purchase, subject to the terms
of the warranty. If you have any questions about your Dyson appliance, call the
Dyson Helpline with your serial number and details of where/when you bought
the appliance. Most questions can be solved over the phone by one of our trained
Dyson Helpline staff.
If your Dyson appliance needs service, call the Dyson Helpline so we can discuss
the available options. If your Dyson appliance is under warranty, and it is a covered
repair, it will be repaired at no cost.
PLEASE REGISTER AS A DYSON APPLIANCE OWNER
To help us ensure that you receive prompt and efficient service, please register as a
Dyson appliance owner. There are three ways to do this:
• Online at www.dysoncanada.ca
• Telephone the Dyson Helpline at 1-877-397-6622.
• Complete the enclosed Warranty Form and mail it to us.
This will confirm ownership of your Dyson appliance in the event of an insurance
loss, and enable us to contact you if necessary.
2 YEAR PARTS AND LABOUR WARRANTY
TERMS AND CONDITIONS OF THE DYSON 2 YEAR PARTS AND
LABOUR WARRANTY
WHAT IS COVERED
• Your Dyson appliance is warrantied against original defects in materials and
workmanship for a period of 2 years from the date of purchase, when used for
normal domestic purposes in accordance with the Dyson Operating Manual.
Please retain your proof of purchase. If you do not have your proof of purchase,
your warranty will start 90 days after the date of manufacture, according to Dyson's
records. This warranty provides, at no extra cost to you, all labour and parts
necessary to ensure that your appliance is in proper operating condition during the
warranty period. The replacement of any part of your appliance under warranty
will not extend the period of warranty. Any parts which are returned to Dyson will
become the property of Dyson. Please call the Dyson Helpline at 1-877-397-6622
for more information.
• This limited warranty is subject to the following terms:
WHAT IS NOT COVERED
Dyson Canada Limited shall not be liable for costs, damages or repairs incurred as
a result of, due to, or from:
• Purchases of appliances from unauthorized dealers.
• Careless operation or handling, misuse, abuse and/or lack of maintenance or use
not in accordance with the Dyson Operating Manual.
• Use of the appliance other than for normal domestic purposes within Canada, e.g.
for commercial or rental purposes.
13