Advertisement
Quick Links
Quick Installation Guide
WAP-EN1750C| AC1750 Ceiling Mount Access Point
I
I.
Product Information
I-1.
Package Contents
1
5
1.
Access Point
2.
Ceiling Mount Bracket
3.
T-Rail Mounting Kit & Screws
4.
Ceiling Mounting Kit & Screws
2
3
6
5.
6.
7.
4
7
Quick Installation Guide
Ethernet Cable
Power Adapter
Advertisement
Related Manuals for Comtrend Corporation WAP-EN1750C
Summary of Contents for Comtrend Corporation WAP-EN1750C
-
Page 1: Quick Installation Guide
Quick Installation Guide WAP-EN1750C| AC1750 Ceiling Mount Access Point Product Information I-1. Package Contents Access Point Quick Installation Guide Ceiling Mount Bracket Ethernet Cable T-Rail Mounting Kit & Screws Power Adapter Ceiling Mounting Kit & Screws... - Page 2 I-2. System Requirements - Existing cable/DSL modem & router - Computer with web browser for access point configuration I-3. Hardware Overview Micro USB Port Power Port Ethernet Port I-4. LED Status LED Color LED Status Description The access point is on Long The access point’s firmware is Blue...
- Page 3 I-5. Reset If you experience problems with your access point, you can reset the device back to its factory settings. This will reset all settings back to default. Press and hold the reset button on the access point for at least 10 seconds.
- Page 4 I-6. Mounting the Access Point to a Ceiling To mount the access point to a ceiling, please follow the instructions below and refer to diagrams A & B. For Wooden Ceilings (refer to diagram A): Place the ceiling mount bracket to a ceiling in your desired location and use the included screws x 4 to fix it into place (i).
- Page 5 For Other Ceilings (refer to diagram B): Drill four holes in your ceiling using the ceiling mount bracket as a guide, and insert the four included wall plugs/screw anchors (i). Align the ceiling mount bracket with your wall plugs/screw anchors and use the included screws x 4 to fix it into place (ii).
- Page 6 Attach the access point to the ceiling mount bracket by aligning the grooves in the access point to the ceiling mount, as shown in iii. Secure the access point firmly in place using the included screw as shown in iv. iii iii I-7.
- Page 7 Select the correct size T-Rail bracket from the two sizes that are included in the package contents. Attach the T-Rail bracket to the ceiling mount using the included screws x 2 as shown in i. You can use the included bracket and longer screws If you need more space between the access point and the T-Rail.
- Page 8 iii iii...
-
Page 9: Quick Setup
iii Quick Setup Your access point is preconfigured in a secured setup and is ready for use right out of the box. The following instructions will help you install your access point and customize your settings. II-1. Initial Setup Connect a router or PoE switch to the access point’s LAN port using an Ethernet cable. - Page 10 If you are using a router, then connect the power adapter to the access point’s 12V DC port and plug the power adapter into a power supply. If you are using a PoE (Power over Ethernet) switch then it is not necessary to use the included power adapter.
- Page 11 Wait a moment for the access point to start up. The access point is ready when the LED is blue. Set your computer’s IP address to 192.168.2.x where x is a number in the range 3 – 100. DHCP is enabled on the access point by default. If no DHCP Service is found, the access point will default to IP address 192.168.2.2.
- Page 12 You will arrive at the “System Information” screen shown below. Follow the instructions below in II-2. Basic Settings to configure basic settings. II-2. Basic Settings The instructions below will help you configure the following basic settings of the access point: •...
- Page 13 To change the access point’s LAN IP address, go to “Network Settings” > “LAN-side IP Address” and you will see the screen below. Enter the IP address settings you wish to use for your access point. You can use a dynamic (DHCP) or static IP address, depending on your network environment.
- Page 14 corresponding numbered fields below, before clicking “Apply”. To configure the security of your access point’s 2.4GHz wireless network(s), go to “Wireless Setting” > “2.4GHz 11bgn” > “Security”. Select an “Authentication Method” and enter a “Pre-shared Key” or “Encryption Key” depending on your choice, then click “Apply”.
- Page 15 Go to “Wireless Setting” > “5GHz 11ac 11an” and repeat steps 3 & 4 for the access point’s 5GHz wireless network(s). To change the administrator name and password for the browser based configuration interface, go to “Management” > “Admin”. Complete the “Administrator Name” and “Administrator Password”...
- Page 16 To set the correct time for your access point, go to “Management” > “Date and Time”. Set the correct time and time zone for your access point using the drop down menus. The access point also supports NTP (Network Time Protocol) so, alternatively, you can enter the host name or IP address of a time server.
-
Page 17: Browser Based Configuration Interface
Browser Based Configuration Interface The browser-based configuration interface enables you to configure the access point’s advanced features. The access point features a range of advanced functions such as MAC filtering, MAC RADIUS authentication, VLAN configurations, up to 32 SSIDs and many more. To access the browser based configuration interface: Connect a computer to your access point using an Ethernet cable. - Page 18 You will arrive at the “System Information” screen shown below. Use the menu across the top and down the left side to navigate.
- Page 19 Click “Apply” to save changes and reload the access point, or “Cancel” to cancel changes. Wait a few seconds for the access point to reload after you “Apply” changes. Your Device is Now Connected! FOR MORE HELP: For instructions on advanced features, FAQ, etc., please visit our online Product Webpage.