Siemens SIPART PS2 Operating Instructions Manual page 8

Table of contents
9.4.2.1 '6.SCUR' Current range of setpoint...................................................................................... 159
9.4.2.2 '7.SDIR' Setpoint direction ................................................................................................... 159
9.4.2.3 '8.SPRA' Setpoint split range start / '9.SPRE' Setpoint split range end ............................... 160
9.4.2.4 '10.TSUP' Setpoint ramp UP / '11.TSDO' Setpoint ramp DOWN ........................................ 161
9.4.2.5 '12.SFCT' Setpoint function ................................................................................................. 161
9.4.2.6 '13.SL0' ... '33.SL20' Setpoint turning point ......................................................................... 162
9.4.2.7 '34.DEBA' Deadband of closed-loop controller .................................................................... 163
9.4.2.8 '35.YA' Start of manipulated variable limit / '36.YE' End of manipulated variable limit ........ 163
9.4.2.9 '37.YNRM' Standardization of manipulated variable............................................................ 164
9.4.2.10 '38.YDIR' Direction of manipulated variable for display and position feedback ................... 165
9.4.2.11 '39.YCLS' Tight closing with manipulated variable .............................................................. 166
9.4.2.12 '40.YCDO' Lower value for tight closing / '41.YCUP' Upper value for tight closing ............. 166
9.4.2.13 '42.BIN1' / '43.BIN2' Function binary input ........................................................................... 167
9.4.2.14 '44.AFCT' Alarm function ..................................................................................................... 168
9.4.2.15 '45.A1' / '46.A2' Response threshold of alarms ................................................................... 170
9.4.2.16 '47.\\FCT' Function fault message ....................................................................................... 171
9.4.2.17 '48.\\TIM' Monitoring time for setting of fault message 'Control deviation' ........................... 171
9.4.2.18 '49.\\LIM' Response threshold of fault message 'Control deviation' .................................... 172
9.4.2.19 '50.PRST' Preset .................................................................................................................. 173
9.4.2.20 '51.PNEUM' Fail in place ..................................................................................................... 174
9.4.2.21 '52.XDIAG' Activating for extended diagnostics ................................................................... 174
9.4.3 Extended diagnostics parameters A to P ............................................................................. 176
9.4.3.1 Partial stroke test 'A.\\PST' .................................................................................................. 176
9.4.3.2 Monitoring of dynamic control valve behavior 'b.\\DEVI' ...................................................... 181
9.4.3.3 Monitoring pneumatic leakage 'C.\\LEAK' ............................................................................ 183
9.4.3.4 Monitoring the stiction (slipstick) 'd.\\STIC' .......................................................................... 185
9.4.3.5 Monitoring the deadband 'E.\\DEBA'.................................................................................... 187
9.4.3.6 Monitoring the lower endstop 'F.\\ZERO' ............................................................................. 188
9.4.3.7 Monitoring the upper endstop 'G.\\OPEN' ............................................................................ 190
9.4.3.8 Monitoring the low limit temperature 'H.\\TMIN' ................................................................... 191
9.4.3.9 Monitoring the high limit temperature 'J.\\TMAX' ................................................................. 193
9.4.3.10 Monitoring the number of total strokes 'L.\\STRK' ............................................................... 194
9.4.3.11 Monitoring the number of changes in direction 'O.\\DCHG' ................................................. 196
9.4.3.12 Monitoring the position average value 'P.\\PAVG' ............................................................... 197
10 Alarm, error, and system messages ..................................................................................................... 201
10.1 Output of system messages in the display .......................................................................... 201
10.1.1 System messages before initialization ................................................................................. 201
10.1.2 System messages during initialization ................................................................................. 202
10.1.3 System messages when exiting the Configuration mode .................................................... 205
10.1.4 System messages during operation..................................................................................... 205
10.2 Diagnostics ........................................................................................................................... 207
10.2.1 Display of diagnostics values ............................................................................................... 207
10.2.2 Saving the diagnostics values .............................................................................................. 207
10.2.3 Overview of diagnostics values ............................................................................................ 208
10.2.4 Meaning of the diagnostics values ....................................................................................... 211
10.2.4.1 Diagnostic value '1.STRKS - Number of total strokes' ......................................................... 211
10.2.4.2 Diagnostic value '2.CHDIR - Number of changes in direction' ............................................ 211
10.2.4.3 Diagnostic value '3.\\CNT - Number of fault messages' ...................................................... 211
10.2.4.4 Diagnostic value '4.A1CNT - Number of alarms 1' / '5.A2CNT - Number of alarms 2' ........ 211
10.2.4.5 Diagnostic value '6.HOURS - Number of operating hours' .................................................. 211
10.2.4.6 Diagnostic value '7.HOURR - Resettable operating hours counter' .................................... 212
8
SIPART PS2 with and without HART
Operating Instructions, 02/2016, A5E00074631-AB