Page 1
LCD-TV Chassis Model GTR23KE LE23T51B GTR27KE LE27T51B GTR32KE LE32T51B GTR32KE LE32T51S SERVICE Manual LCD TV Fashion Feature - RF, DVI-D, PC(Analog), 2Scart, Component, Video, S-Video - Brightness : 500cd/㎡ - Contrast Ratio : 23": 800:1, 27": 1000:1, 32": 800:1 - Respense time : 16ms...
Page 2
Samsung Electronics Co.,Ltd. 416, Maetan-3Dong, Yeongtong-Gu, Suwon City, -This Service Manual is a property of Samsung Gyeonggi-Do, Korea, 443-742 Electronics Co., Ltd. Printed in Korea Any unauthorized use of Manual can be punished P/N : BN82-00128R-03 under applicable International and/or domestic law.
1 Precautions 1 Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1 Safety Precautions 1-1-1 Warnings For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC power jack before servicing.
1 Precautions 1-2 Servicing Precautions WARNING: An electrolytic capacitor installed with the wrong polarity might explode. Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
1 Precautions 1-4 Installation Precautions 1. For safety reasons, more than two people are 6. Keep the antenna far away from any high-voltage required for carrying the product. cables and install it firmly. Contact with the highvoltage cable or the antenna falling over may 2.
3 Alignments and Adjustments 3 Alignments and Adjustments 3-1 General Alignment Instuction 1. Usually, a color LCD-TV needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync. 2. Use the specified test equipment or its equivalent. 3.
3 Alignments and Adjustments 3-2 Factory Mode Adjustments 3-2-1 Entering Factory Mode To enter 'Service Mode' Press the remote -control keys in this sequence : - If you do not have Factory remote - control Power OFF INFO MENU MUTE Power On 3-2-2 Panel Check - Specially for LE32T51BX, You have to check Panel Maker Because of different adjustments as follows.
Page 15
3 Alignments and Adjustments 3-2-3 Factory Mode Tree - If you have Factory remote - control [INFO] -> [FACTORY] 1. Calibration 1. Calibration : W/B Calibration 2. Option Byte 3. W/B AV Calibration 4. VCTi DTV Calibration 5. YC Delay PC Calibration 6.
Page 17
3 Alignments and Adjustments 3-3 White Balance - Calibration 3-3-1 White Balance -Calibration 1. Calibration DTV Calibration PC Calibration (Calibration Condition refer to next page) 3-3-2 White Balance - Adjustment (low light) (hight light) 3. W/B Sub Bright Sub Contrast R offset R gain G offset...
Page 18
3 Alignments and Adjustments 3-3-4 Method of Adjustment 1. Adjust the basic level of Component and PC input signals. a) Set the input to the mode in which the adjustment will be made (Component PC ). * Input signal - Component Mode : Model #6 (1280*720 Mode), Pattern #15 (picture 4-1) - PC Mode : Model #21 (1024*768 Mode), Pattern #17 (Picture 4-2) b) Enter factory Calibration (DTV, PC Mode Only).
Page 19
3 Alignments and Adjustments d) Adjust the high light. (Refer to table 1, 2 in adjustment position by mode) - Adjust red gain ('x') and blue gain ('y') to the color coordinates. ( x : 263, y : 267 ) * Do not adjust the green gain and sub-contrast (Y) data.
Page 20
3 Alignments and Adjustments 3-4 TORINO Micom Update 3-4-1 Installing G-Probe 1. Uncompress GProbe5.1.0.18.zip. 2. Run GProbe5.1.0.18.exe. 3. The files are created in the C: Program Files Genesis Microchip GProbe 5 folder. 4. Copy the ispoak_spi.hex file to the C: Program Files Genesis Microchip GProbe 5 folder. 5.
Page 21
3 Alignments and Adjustments 3-4-2 Connecting to the MAIN PCB Switch off <Micom Download Jig Top Side: Note the direction of the switch> <Bottom Side> Connect to the MAIN PCB. Connect to the PC...
Page 22
3 Alignments and Adjustments 3-4-3 Update Procedures 1. Open mgm.txt in the C: Program Files Genesis Microchip GProbe 5 folder. 2. The following result will appear. // Batch file to program a sPI serial flash using ISP. // Moving the stack to high memory area is now taken care of in IROM // through the "Reset 0"...
Page 23
3 Alignments and Adjustments The Micom program is to be copied to the folder marked in red and the name of the program is to be the same as the file name marked in blue. (If the Micom program is not in the folder marked in red, change the path to the folder which includes the Micom program and then save the file.) 3.
Page 24
3 Alignments and Adjustments 4. Enter 'batch mgm.txt' as show in the following figure and press Enter or click the Execute button to update Micom. If the MICOM update is successfully completed, the above message appears. 3-12...
4 Troubleshooting 4 Troubleshooting 4-1 No Power LAMP off, power indicator Check a connection a power cable. LED red color? Does proper DC 12V Change a Assy PCB Power. appear at C820, C823? Does proper DC A3.3V, Check a IC816, IC815 A5V appear at Change a main PCB ass'y.
Page 26
R781, R782, R783? cable. Change a main PCB ass'y. Does the digital data appear Check a IC310. at output of LVDS TX(R422~R425, Change a main PCB ass'y. R430~R433)? Check a LVDS cable? Please, Call to Samsung Co. LTD. Replace a lcd panel?
Page 27
4 Troubleshooting WAVEFORMS R,G,B Output Signal Digital Output Data of IC310...
Page 28
FT2704, 2705, 2706, 2708? change a main PCB ass'y. Does the digital data Check a IC310. appear at output of IC310 Change a main PCB ass'y. LVDS(R422~R425, R430~R433)? Check a LVDS cable? Please, Call to Samsung Co. LTD. Replacea lcd panel?
Page 29
4 Troubleshooting WAVEFORMS Digital Output Data of IC310 Signal of DVI(Data)
Page 30
Check a IC210. C268? Change a main PCB ass'y. Does the digital data appear Check a IC310. at output of R422~R425, Change a main PCB ass'y. R430~R433? Check a LVDS cable? Please, Call to Samsung Co. LTD. Replacea lcd panel?
Page 31
4 Troubleshooting WAVEFORMS Digital Output Data of IC310 Tuner_CVBS Output Signal...
Page 32
Dose the signal Check a connection harness. appear at R7003? Does the digital data appear Check a IC310. at output of R422~R425, Change a main PCB ass'y. R430~R433? Check a LVDS cable? Please, Call to Samsung Co. LTD. Replacea lcd panel?
Page 33
4 Troubleshooting WAVEFORMS Digital Output Data of IC310 Tuner_CVBS Output Signal...
Page 34
Dose the signal appear at Check a connection harness. R7001, R7002? Does the digital data appear Check a IC310. at Output of R422~R425, Change a main PCB ass'y. R430~R433? Check a LVDS cable? Please, Call to Samsung Co. LTD. Replacea lcd panel? 4-10...
Page 35
4 Troubleshooting WAVEFORMS Digital Output Data of IC310 Analog Signal(Y,C) 4-11...
Page 36
4 Troubleshooting 4-7 No Sound Connect a sound cable. Picture is display, no sound. control a volume. Does the signal appear at Pin 12, 1(CH1_L, R Sound) Check a connection harness and and Pin 15, 2 headphone jack. (CH2_L, R Sound) of IC613? Check the DC 8V Check a IC813.
Page 37
4 Troubleshooting WAVEFORMS The Signal are Inputed to IC610 DC +8V Output WaveForm 4-13...
Page 39
5 Exploded View & Parts List 5 Exploded View and Parts List - You can search for updated part codes through ITSELF web site. URL : http://itself.sec.samsung.co.kr/ 5-1 LE23T51B M0013 M0014 M0107 T0175 M0111 M0003...
Page 45
6 Electrical Parts List 6 Electrical Parts List -You can search for updated part codes through ITSELF web site. URL : http://itself.sec.samsung.co.kr/ 6-1 LE23T51BX/XEU Parts list Level Loc. No. Code No. Description & Specification SA/SNA LE23T51BX/XEU LE23T51B,Q54B/23T50-GTR,23,LCD-TV,UNITED M0001 BN90-00791B ASSY COVER FRONT;TORINO,23EO,23T50...
Page 67
8 Wiring Diagrams CN802 - Front control NAME SDA-T SCL-T GND GND IDENT HP-L HP-R INPUT1 INPUT1INPUT2 Function Define - A5V Front control board poewr supply - KEY INPUT1,2/SDA/SCL Key control, from the memu, change up/down Etc. - IR Remote control signal - LED Control the timing and stand by LED color CN815 - Panel control...
Page 69
8 Wiring Diagrams 8-4 Power Board Layout...
Page 70
8 Wiring Diagrams CN801 - AC Input NAME Live Netural VOLTAGE Functing Define - Refer to : AC Input CN801 - Main Board power supply NAME 13V GND 5.4V 5.4V 5.4V GND GND GND GND ST7V PWR Functing Define - ST7V Stand-By Output - PWR Power On/Off Control - Refer to : CN801 function define CNM804 - Panel control...
Page 71
8 Wiring Diagrams CN802 - Inverter power supply NAME 24V GND GND GND GND Functing Define - AMLCD Panel Inverter Power - 24V LAMP INVERTER Voltage - B/L Brightness sensor power - A_D ANA_DIMMING - P_D PWM_DIMMING CN803 - Inverter power supply NAME 24V GND GND GND GND...
Page 73
8 Wiring Diagrams CN801 - AC Input NAME Live Netural VOLTAGE Functing Define - Refer to : AC Input CN801 - Main Board power supply NAME 13V GND 5.4V 5.4V 5.4V GND GND GND GND ST7V PWR Functing Define - ST7V Stand-By Output - PWR Power On/Off Control - Refer to : CN801 function define CNM804 - Panel control...
Page 74
8 Wiring Diagrams CN803 - Inverter power supply NAME 24V GND GND GND GND Functing Define - AMLCD Panel Inverter Power - 24V LAMP INVERTER Voltage - B/L Brightness sensor power - A_D ANA_DIMMING - P_D PWM_DIMMING CN804 - Inverter power supply NAME 24V GND GND GND GND...
Page 76
9 Schematic Diagrams 9 Schematic Diagrams - This Document can not be used without Samsung s authorization. 9-1 Power & Function Schematic Diagram DC +8V...
Page 77
9 Schematic Diagrams - This Document can not be used without Samsung s authorization. 9-2 In_Out_Jack Schematic Diagram...
Page 78
9 Schematic Diagrams - This Document can not be used without Samsung s authorization. 9-3 In-Out-Jack Schmetic Diagram R,G,B Output Signal of IC906 Signal of DVI(Data) Tuner_CVBS Output Signal Analog Signal(Y,C)
Page 79
9 Schematic Diagrams - This Document can not be used without Samsung s authorization. 9-4 Video Decoder & Sound Processing IC Schematic Diagram Tuner_CVBS Output Signal...
Page 80
9 Schematic Diagrams - This Document can not be used without Samsung s authorization. 9-5 Sound Amp Schmetic Diagram The Signal are Inputed to IC610 DC +8V Output WaveForm...
Page 81
9 Schematic Diagrams - This Document can not be used without Samsung s authorization. 9-6 Scaler IC Schmetic Diagram...
Page 82
9 Schematic Diagrams - This Document can not be used without Samsung s authorization. 9-7 Memory & LVDS Output Schmetic Diagram Digital Output Data of IC310...
Page 84
10 Operating Instructions and Installation 10 Operating Instructions and Installation 10-1 Front - The product color and shape may vary depending on the model. 1. SOURCE (POWER) Displays a menu of all of the available input sources Press to turn the TV on and off. (TV, Ext.1, Ext.2, AV, S-Video, Component, PC, DVI).
10 Operating Instructions and Installation 10-2 Connection Panel 10-2...
Page 86
10 Operating Instructions and Installation 1. Connecting an Aerial or Cable Television Network To view television channels correctly, a signal must be received by the set from one of the following sources: - An outdoor aerial / A cable television network / A satellite network 2.
10 Operating Instructions and Installation 10-3 Remote Control 1. Television Standby button 2. Number buttons for direct channel access 3. One/Two-digit channel selection Volume increase Volume decrease 5. Temporary sound switch-off 7. Displays the main on-screen menu 8. Sound effect selection 9.
10 Operating Instructions and Installation 10-4 Installing the Stand 1. Place the TV faced down on a soft cloth or cushion on a table. 2. Put the stand into the hole at the bottom of the TV. 3. Insert screw into the hole indicated and tighten 10-5...
Page 89
10 Operating Instructions and Installation Memo 10-6...
11 Disassembly and Reassembly 11 Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the LE23T51B/LE27T51B/LE32T51B TFT-LCD monitors. WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling these components. (ONLY LE32T51B) Check the connector of POWER BOARD which are CNM 802, 803.
Page 91
11 Disassembly and Reassembly 23"(AM-LCD Panel) 27"(CMO Panel) 32"(AM-LCD Panel) 32" (AUO Panel) 3. Disconnect cables and remove 6 screws from the power board. 4. Remove 4 screws from the main board. Lift up the power board. 5. Lift up the main board and remove 10 secews from the BRKT. 11-2...
Page 92
11 Disassembly and Reassembly 6. Remove 4 screws and Lift up the Lcd panel. 7. Remove 4 screws 11-2 Reassembly Reassembly procedures are in the reverse order of disassembly procedures. 11-3...
Page 93
11 Disassembly and Reassembly Memo 11-4...
13 Circuit Descriptions 13 Circuit Descriptions 13-1 Block description Torino consists of three main blocks 1. Main board : Video signal processing 2. SMPS board : Power supply 3. Panel Inverter & T-con board : LCD Panel control 13-1...
14 Reference Infomation 14 Reference Infomation 14-1 Technical Terms - TFT-LCD - Auto Configuration(Auto adjustment) (Thin film Transistor Liquid Crystal Display) This is an algorithm to adjust monitor to optimum ADC(Analog to Digital Converter) condition by pushing one key. This is a circuit that converts from analog signal to digital signals.
Page 107
14 Reference Infomation - T.M.D.S - Interlace and Non-Interlace Methods (Transition minimized Differential Signaling) Showing the horizontal lines of the screen from the a kind of transmission method for Digital. top to the bottom in order is called the Non- It can be used from Video card to Main PBA.
Page 108
Enables high picture quality and clear sound channel to obtain the best viewing conditions. The throughout the country regardless of the location of Samsung LCD TV has both automatic and manual the viewer. channel fine-tuning features to enable the viewer to adjust their desired settings.
Page 110
14 Reference Infomation 14-2-2 Component 14-2-3 S-Video Separate RCA Green Pb (Cb) RCA Blue Pr (Cr) RCA Red Audio L 14-2-5 D-SUB RCA White Separate Audio R RCA Red Green Blue 14-2-4 A/V GND Red GND Green GND Blue RCA Yellow CVBS DDC Input power(+5V) Audio L...
Page 111
14 Reference Infomation 14-2-7 Scart 1 Signal Signal Audio output R Audio input R Video GND (RGB red) Audio output L Audio common GND RGB red input Video GND (RGB blue) Fast Blanking signal (RGB switching) Audio input L Video output GND RGB blue input Video input GND Switching voltage...
14 Reference Infomation 14-3 Timing Chart This section of the service manual describes the timing that the computer industry recognizes as standard for computer- generated video signals. 14-3-1 LCD Panel Mode1 mode 14-7...