Related Manuals for Elkay DSBS130UVPC
Summary of Contents for Elkay DSBS130UVPC
-
Page 1: Table Of Contents
Installation and Maintenance Manual DSBS130UVPC DSBSH130UVPC Table of Contents Before You Begin – Requirements for Operating the Keypad Installation Routine Maintenance Mounting Dimensions Declaration of Conformity Troubleshooting Operating Environment Association Replacement Parts Water Recommendations for Safeguarding the Environment Electrical Explanation of Warning/Safety Icons... -
Page 2: Declaration Of Conformity
DSBS130UVPC and DSBSH130UVPC Installation and Maintenance Manual Declaration of Conformity D.M. 174 Materials compliant for contact with drinking water This unit is intended for the dispensing of drinking water, and so the materials that enter into direct contact with water meet the criteria for food-grade components pursuant to the current legislation. In addition, the unit is manufactured in compliance with Italian Ministerial Decrees 174 of 04/06/2004 and 25 of 02/07/2012. -
Page 3: Recommendations For Safeguarding The Environment
For safety reasons keep the packaging material out of the reach and sight of children. Scrappage The DSBS130UVPC and DSBSH130UVPC water coolers are made using recyclable material. These units are marked in compliance with European Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). -
Page 4: Introduction
Introduction The DSBS130UVPC and DSBSH130UVPC coolers bring contemporary style and state-of-the-art technology to commercial water dispensers. DSBS130UVPC and DSBSH130UVPC offer light, compact and powerful performance made entirely from stainless steel. Multiple dispensing options: cold still water, cold sparkling water, room temperature still water and/or hot water. -
Page 5: Components Guide
Drip tray Thermostat Power cord DSBSH130UVPC Keypad Boiler switch Power button Water inlet Drip tray inlet Thermostat Power cord DSBSH130UVPC keypad DSBS130UVPC keypad Room temperature still Cold sparkling Cold still Cold still Cold sparkling dispenser dispenser dispenser Hot dispensers dispenser dispenser... -
Page 6: Product Specifications
DSBS130UVPC and DSBSH130UVPC Installation and Maintenance Manual Product Specifications Specification DSBS130UVPC DSBSH130UVPC Cooling capacity gal/h (lt/h) 1.5 (5.7) 1.5 (5.7) 32 6 oz. cups/h 32 6 oz. cups/h Cold water temperature* 42°F – 50°F 42°F – 50°F (5.5°C – 10°C) (5.5°C –... -
Page 7: Before You Begin - Requirements For Installation
Before You Begin – Requirements for Installation Mounting Dimensions Over counter (includes 4" clearance on sides and back) DSBS130UVPC DSBSH130UVPC Depth Width Depth Width 23.2” (589mm) 18.3” (465mm) 23.2” (589mm) 18.3” (465mm) Height Height 20.5” (520.7mm) 20.5” (520.7mm) Footprint: Footprint: 10.3”... -
Page 8: Operating Environment
DSBS130UVPC and DSBSH130UVPC Installation and Maintenance Manual Operating Environment Install the machine in a clean, dry, well-ventilated room. It is designed to function correctly in environments with a temperature of 16°C to 32°C – Climatic Class N, (between 61°F and 90°F). -
Page 9: Tools You Will Need
Tools You Will Need (2) 8" adjustable wrenches (1) 12" adjustable wrench (1) 12" pipe cutter (1) 10" adjustable pliers (1) universal screwdriver (1) wire cutting pliers Unpacking the Kit Remove the front panel (labeled FRONT) and cover of the wooden packing case. -
Page 10: What's In The Kit
(1) 10' coil water tubing (blue) 1/4” OD 3/8” OD (1) CO regulator (1) supply hose 1/2 ips x 3/8 tube x 12” long PLUS (1) DSBS130UVPC or DSBSH130UVPC (2) 3/8" – quick (1) water (1) water water cooler connect connector shutoff valve pressure... -
Page 11: Installing The Machine
Installing the Machine CAUTION: Wear safety gloves when handling the machine. Metal edges are sharp, and touching them could result in minor or moderate injury. 1. Install external water filter and CO cylinder. 1. Use (2) Phillips head screws to mount bracket to under-counter wall. 2. - Page 12 DSBS130UVPC and DSBSH130UVPC Installation and Maintenance Manual 2. Cut, size and connect water and CO piping to fit your installation. NOTICE: The water pressure entering the machine must be between 14.5 psi (0.10 MPa) minimum and 51 psi (0.35 MPa) maximum. If the inlet water pressure is higher than 51 psi, the water pressure regulator supplied must be used.
- Page 13 3. Place the machine in its operating location. NOTICE: Ensure machine remains level while being lifted into place. 4. Connect external water and CO piping. DSBS130UVPC DSBSH130UVPC Water input Water input input input 5. Plug the machine into the wall socket and turn it on.
- Page 14 DSBS130UVPC and DSBSH130UVPC Installation and Maintenance Manual 6. Purge the water lines. 1. Place receptacle beneath tap to catch dispensed water. Discard water as necessary. DSBS130UVPC DSBSH130UVPC Press dispensing Press dispensing button button 2. Allow water to run continuously until flow is clear of air.
- Page 15 8. Open the CO valve. 1. Using a screwdriver slowly turn valve screw counterclockwise (left) to open valve. 2. Continue until pressure reads 50 to 58 psi max. 9. Re-purge the line for sparkling water. NOTICE: The water will flow flat at first, then gradually become more sparkling as the line is purged of still water.
-
Page 16: Operating The Keypad
DSBS130UVPC and DSBSH130UVPC Installation and Maintenance Manual Operating the Keypad DSBS130UVPC To dispense your water serving Hold down the button for that dispenser. To stop dispensing your water serving Release the button for that dispenser. Operating the Keypad DSBSH130UVPC To dispense your water serving Hold down the button for that dispenser. -
Page 17: Routine Maintenance
Routine Maintenance Daily Clean all external surfaces of the machine, the drip tray and the dispensing nozzles. NOTICE: It is recommended that all external components of the product be cleaned daily. It is recommended that you use dish soap, warm water and a clean, soft cloth to clean the product. DO NOT USE THE FOLLOWING PRODUCTS: Do not use ... - Page 18 4. Place a receptacle under the still water dispenser and dispense continuously for a minimum of two gallons to purge air and fine carbon particles from filter. Sanitize the machine NOTICE: This operation must be carried out by your ELKAY reseller or by a qualified technician. When required Replace the UV lamp CAUTION: The light emitted by the ultra-violet lamp may cause serious burns to the eyes and skin.
- Page 19 Set the thermostat COLDER 1. Set the thermostat between 5 and 6 to control the temperature of the cold water. 1000003719 (Rev. A - 02/2017)
-
Page 20: Troubleshooting
DSBS130UVPC and DSBSH130UVPC Installation and Maintenance Manual Troubleshooting Problem Possible Cause Action To Take No water dispense The main water valve is closed Open the valve The power switch is set to OFF Set the power switch to ON Malfunction in the ribbon cable connection/... - Page 21 Problem Possible Cause Action To Take Poor sparkling water quality Incorrect air gap in the carbonator Close the CO cylinder valve, pull up the ring on safety valve (on the carbonator bowl head) until all air gap is out Use of rinse aid or highly polished glass Avoid excessive use of rinse aid The CO regulator is set low...
- Page 22 DSBS130UVPC and DSBSH130UVPC Installation and Maintenance Manual Contacting Customer Support Elkay Manufacturing Company 2222 Camden Court Oak Brook, IL 60523 800-726-0553...
-
Page 23: Replacement Parts
Replacement Parts DSBSH130UVPC DSBS130UVPC DSCABBSH Part Number Product Name 1000002622 Motor Fan 120x120x25 1000002623 Booster Pump 1000003890 Level Control 1000002625 General Power Switch 1000003892 Ice Bank Thermostat Dry Cooling K50 1000002627 Feet 4MA 1000002631 Inlet Solenoid Valve 1000003894 Exit Solenoid Valve 2IN-1OUT... - Page 24 160217...