Related Manuals for Comtrend Corporation WAP-EN1750R
Summary of Contents for Comtrend Corporation WAP-EN1750R
- Page 1 Quick Installation Guide WAP-EN1750R| AC1750 Outdoor Wireless Access Point...
-
Page 2: Product Information
Product Information I-1. Package Contents Access Point Wall/Pole Mount Screws Kits Antennas x 6 Quick Installation Guide CD (User Manual & QIG) (2.4Gx3 & 5Gx3) Wall Mount Bracket x 1... - Page 3 I-2. System Requirements • Existing cable/DSL modem & router • Computer with web browser for access point configuration I-3. Hardware Overview A. LAN (PoE) B. 3 LED + 1 Reset LAN port with Power over Ethernet (PoE PD, IN) 3 LEDs and Reset Interface I-4. LED Status LED Behavior Green The access point is on.
- Page 4 I-5. Reset If you experience problems with your access point, you can reset the device back to its factory settings. This resets all settings back to default. 1. Press and hold the reset button on the access point for at least 10 seconds then release the button.
- Page 5 2. Fix the wall mount with the access point to the wall using wood/gyprock screws. 3. Fix the wall mount with the access point to the pole using stainless tie back straps.
-
Page 6: Quick Setup
Quick Setup Your access point is preconfigured in a secured setup and ready for use right out of the box. The following instructions will help you install your access point and customize your settings. II-1. Connecting the Access Point to Your Network Connect a router (with a PoE Injector) or PoE switch to the access point’s LAN port using an Ethernet cable. - Page 7 II-2. Initial Setup 1. Connect the access point to a PoE Switch via an Ethernet cable. 2. Connect a computer to the PoE Switch via an Ethernet Cable. 3. Wait a moment for the access point to start up. The access point is ready when the LED is green.
- Page 8 6. You will be prompted for a username and password. Enter the default username “admin” and the default password “admin”. 7. You will arrive at the “System Information” screen shown below. 8. Next, follow the instructions below in “II-3. Basic Settings” to configure the access point’s basic settings.
- Page 9 II-3. Basic Settings The instructions below will help you to configure the following basic settings of the access point: It is recommended you configure these settings before using the access point. • LAN IP Address • 2.4 GHz and 5 GHz SSID & Security •...
- Page 10 3. To change the SSID and password of your access point’s wireless network(s), go to “Wireless Setting” > “2.4GHz” > “Basic”. Enter the new SSID for your 2.4GHz wireless network in the “SSID1” field and click “Apply”. 4. Go to “Wireless Setting” > “2.4GHz” > “Security”. Enter a new password for your 2.4GHz wireless network in the “Pre-shared Key”...
- Page 11 5. Go to “Wireless Setting” > “5GHz 11ac 11an” and repeat steps 3 & 4 for the access point’s 5GHz wireless network. 6. To change the login password for the browser based configuration interface, go to “Management” > “Admin”. 7. Complete the “Administrator Name”, “Administrator Password” and “Confirm”...
-
Page 12: Browser Based Configuration Interface
9. Select the correct time zone for your access point from the drop down list. The access point also supports NTP (Network Time Protocol) so alternatively you can enter the host name or IP address of a time server. Click “Apply” when you are finished. 10. - Page 13 4. You will arrive at the “System Information” screen shown below. 5. Use the menu across the top and down the left side to navigate. 6. Click “Apply” to save changes and reload the access point, or “Cancel” to cancel changes. Wait a few seconds for the access point to reload after you “Apply”...
- Page 14 Your Device is Now Connected! FOR MORE HELP: For instructions on advanced features, FAQ, etc., please visit the WAP-EN1750R product webpage online. For more information: YouTube: https://www.youtube.com/user/ComtrendConnection Facebook: https://facebook.com/Comtrend Website: http://us.comtrend.com/ Support: Visit our website or call 1-877-COMTREND (1-877-266-8736)