SolarEdge zigbee Quick Installation Manual
Hide thumbs
Also See for zigbee:
- Installation manual (18 pages) ,
- Quick installation manual (56 pages) ,
- Setting up (6 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for SolarEdge zigbee
Summary of Contents for SolarEdge zigbee
-
Page 3: Table Of Contents
Installieren der ZigBee-Antenne und des Slave-Moduls 19 Home-Gateway Installation .......... 21 Installationsrichtlinien ............21 Verbinden des Home-Gateways .......... 22 Überprüfung der Verbindung..........23 Français ................25 Guide d’installation rapide du Kit ZigBee de SolarEdge ..25 Interfaces d’utilisateur de la passerelle domestique ..26 MAN-01-00155-1.0... - Page 4 Connexion de la passerelle domestique ......33 Vérification de la connexion ..........34 Italiano ................35 Guida rapida per l'installazione del kit ZigBee SolarEdge ... 35 Interfaccia utente dell’home gateway esterno ..... 36 Connettori ................37 DIP Switch ................37 Pulsante di configurazione ..........
- Page 5 Contents De ZigBee antenne en Slave-module installeren ..49 Home Gateway installatie ..........51 Installatie richtlijnen ............51 De Home Gateway aansluiten ..........52 De verbinding controleren ..........52 MAN-01-00155-1.0...
-
Page 7: English
Installation Guide This quick guide describes how to connect a SolarEdge ZigBee home gateway and a ZigBee slave device. One slave device is supplied with this kit. For full installation and safety details refer to the SolarEdge Home Gateway Installation Guide and to the SolarEdge ZigBee Slave Kit Installation Guide. -
Page 8: Home Gateway User Interfaces
SolarEdge ZigBee Kit Quick Installation Guide Home Gateway User Interfaces Antenna Link LED (Yellow) S_OK LED (Green) Configuration Button Signal strength LEDs (x3, Green) Micro-USB Port Power LED (Green) Ethernet Port DIP Switches MAN-01-00155-1.0... -
Page 9: Connectors
Micro-USB: Connection to the power supply. This port can also be used for connecting to a computer for advanced configuration or SW upgrade. Ethernet: Connecting the SolarEdge gateway to the SolarEdge monitoring portal through an Ethernet switch/router. The Ethernet switch/router should be connected to the Internet. -
Page 10: Leds
SolarEdge ZigBee Kit Quick Installation Guide LEDs The gateway has four LED indicators, as follows: Label and Color Indication Functionality Blinking - There has been Link (yellow) Communication with associated slave(s) ZigBee communication in the last 15 minutes. The LED blinks according to the number of slaves as follows: for each slave 0.5 second... -
Page 11: Installing The Zigbee Antenna And Slave Module
SolarEdge ZigBee Kit Quick Installation Guide Installing the ZigBee Antenna and Slave Module Install the supplied ZigBee slave module in the slave device (inverters or SMI; the steps herein describe connection to an inverter). Connect the ZigBee antenna to the mounting clip and attach the mounting clip to the top of the inverter or to the wall. - Page 12 10 Tighten the cable to the communication board using the two supplied cable ties. 11 Connect the RF cable to the ZigBee slave module and tighten manually. 12 Close the inverter cover as described in its manual.
-
Page 13: Home Gateway Installation
-20 C (-4 F) to +60 C (140 F). Protect the SolarEdge home gateway from dust, wet conditions, corrosive substances, and vapors. Install the SolarEdge home gateway on a wall or place it on the desk. Ensure that the antenna is vertically oriented. -
Page 14: Verifying The Connection
If using a static IP instead of automatic DHCP, configure the home gateway as described in Appendix B of the SolarEdge Home Gateway Installation Guide. Device Discovery: Press the configuration button on the home gateway for 5-10 seconds and release it after all LEDS have turned on. -
Page 15: Leds
LED is ON, the signal strength is Low. Consider relocating the home gateway closer to the inverter to improve reception. If all signal strength LEDs are OFF, consider using a SolarEdge ZigBee repeater (sold separately) between the home gateway and the inverter.