Page 1
LCD-Monitor Chassis : LS24KIE Model : 2493HM SERVICE Manual TFT-LCD Monitor Contents 1. Precautions 2. Product specifications 3. Disassembly and Reassemble 4. Troubleshooting 5. Exploded View & Part List 6. Wiring Diagram 7. Schematic Diagram 2493HM Refer to the service manual in the GSPN (see the rear cover) for the more information.
Page 4
3. Disassembly and Reassemble 3. Disassembly and Reassemble This section describes the disassembly and reassembly sequences for this monitor. WARNING: As this monitor has parts that are sensitive to static electricity, be careful when handling them. 3-1. Disassembly Cautions: 1. Turn the monitor off before beginning the disassembly process. 2.
Page 5
3. Disassembly and Reassemble Part Description Picture Description Screws 3. Seperate the Inverter Cable from the SMPS. Inverter Cable 4. Remove the LVDS cable. 5. Remove the cable from the SHIELD-COVER. ASSY CHASSIS 6. Remove the cable. 7. Remove the hexagonal screws from the bottom of the Shield.
Page 6
3. Disassembly and Reassemble Part Description Picture Description Screws 8. Seperate the Function Cable and the Speaker Cable from the Main Board. Function Wire 9. Remove the four (4) screws from both sides of the speakers. Speaker 10. Remove the Panel and Chassis, separate the Speaker and Function wire from the Decoration and then separate the Decoration.
Page 7
3. Disassembly and Reassemble Part Description Picture Description Screws 12. Assemble the product in the reverse order of the disassembly. When closing the cover, close the lower side of the cover first. (Otherwise, the product may be damaged.) Back Cover Reassembly procedures are in the reverse order of disassembly procedures.
1. Precautions 1. Precautions 1-1. Safety Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1-1. Warnings For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC power jack before servicing.
1. Precautions 1-2. Servicing Precautions WARNING: An electrolytic capacitor installed with the wrong polarity might explode. Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
1. Precautions 1-4. Installation Precautions For safety reasons, more than two people are required for carrying the product. Keep the power cord away from any heat emitting devices, as a melted covering may cause fire or electric shock. Do not place the product in areas with poor ventilation such as a bookshelf or closet. The increased internal temperature may cause fire.
Quick Setup Guide BH68-01387A Warranty Card BH68-00344C (Not available in all locations) User’s Guide, Monitor Driver, BN59-00660A Natural Color software, Samsung Electronics MagicTune™ software Service center D-Sub(15 Pin) Cable BN39-00244B Shipped as assembled with the set Power Cord 3903-000085 DVI-D Cable...
Page 33
7. Schematic Diagram 7-2. Schematic Diagram 7-2-1 Analog, Function, Sound input, Speaker out Block - This Document can not be used without Samsung’s authorization. +5V_DDC Do Not Place R101 R164 TP_DDCA_WP 10Kohm 10Kohm DDC_WP TP_DDCA_SCL XREF TP_DDCA_SDA R106 TP_DDCA_GND 0ohm...
Page 34
7. Schematic Diagram 7-2-2 DVI, HDMI input Block - This Document can not be used without Samsung’s authorization. +3.3V_LIVE HDMI_INPUT +5V_DDC BD1004 100nF C1141 C1148 100nF +5V_DDC DDC_SCL_HDMI MGND5 MGND3 D105 D106 D107 D108 D109 D110 D111 D112 DDC_SCL_DVI VDD50...
Page 35
7. Schematic Diagram 7-2-3 Scaler, Memory Block - This Document can not be used without Samsung’s authorization. +5V_PANEL DATE R9022 22ohm 1/10W LED_GREEN R360 R347 XREF +3.3V_LIVE 300ohm 300ohm R370 C360 10Kohm 10uF R348 PANEL INTERFACE 1/10W AVDD_ADC AVDD_DVI AVDD_SIF...
Page 36
7. Schematic Diagram 7-2-4 Power, Speaker out, Headphone out Block - This Document can not be used without Samsung’s authorization. +5V_PANEL +5V_AUDIO +5V_IN FT605 +5.8V_AMP Q701 2SC2412K-Q BLM41P600S +5V_IN SPEC_STRESS_1 C604 100nF FT604 C605 +18V_IN 100uF BLM41P600S IC702 MP3213DH CN600...
4. Troubleshooting 4. Troubleshooting 4-1. Troubleshooting Before troubleshooting, setup the PC ‘s display as below. • Resolution: 1920 x 1200 • H-frequency: 75 kHz • V-frequency: 60 Hz If no picture appears, make sure the power cord is correctly connected. Check the following circuits.
4. Troubleshooting 4-2. When the Power Does Not Turn On The LED on the front panel of the monitor does not work when the power is connected and the Symptom Power button is pressed. Check if the Power switch on the rear panel of the monitor has been turned on. Check the SMPS fuse and the SMPS output power.
Page 39
4. Troubleshooting 4-2-1. Circuit Diagram and Waveform for Power Failures ① ② ②...
4. Troubleshooting 4-3. When a blank screen is displayed (Analog) The LED power is on but no picture is displayed on the screen when the D-SUB cable is Symptom connected Check if the D-SUB cable has been connected. Major checkpoints Check if the LVDS cable has been connected properly to the LCD panel.
Page 41
4. Troubleshooting 4-3-1. Circuit diagrams and waveforms (analog) when a blank screen is displayed on the monitor ① ② ③ ④...
4. Troubleshooting 4-4. When a Blank Screen Is Displayed (DIGITAL) Symptom The LED power is on but no picture is displayed on the screen when the DVI cable is connected. Check if the DVI cable has been connected. Major checkpoints Check if the LVDS cable has been properly connected to the LCD panel.
Page 44
4. Troubleshooting 4-4-1. Circuit diagrams and waveforms (DVI) when a blank screen is displayed on the monitor ① ② ③...
4. Troubleshooting 4-5. Error Examples and Actions Error Appearance Symptoms and Actions Remarks Symptom: DVI signals are not recognized. *On how to input DDC, refer to the training manual. Cause: This error occurs because the PC cannot recognize the mode information since the DVI DDC is not input to the monitor.
4. Troubleshooting 4-6. Adjustment 4-6-1. Service Adjustment Conditions Precautions before a Service Adjustment. 1) Check whether the devices for the service adjustment are operating normally. 2) Secure a space that is sufficiently wide for disassembling the monitor. 3) Prepare a soft mat on which the monitor will be disassembled. Entering Service Mode.
Page 48
4. Troubleshooting Entering the Micom Code 1. Run “winDDC” 2. Click “Load File” and select the latest code in the format of “*.hex”. 4-12...
Page 49
4. Troubleshooting 3. Click “Program” Entering the EDID You can update the EDID/DDC (Analog / DVI / HDMI) using the DDC Manager Jig. Connect the devices as shown below MTI-2059 DDC Manager Signal Connector Connect to the Monitor (D-SUB/ DVI/HDMI) 4-13...
4. Troubleshooting 4-6-3. Service Function Spec. 1. 1. Set the Brightness and Contrast to 0. 2. Press and hold the Enter and Source keys. 3. The SVC Function OSD appears. *To exit from the SVC Function OSD, you have to turn the power off. Panel Information Software Version Checksum...
4. Troubleshooting Replacing the Panel When replacing the panel: After replacing the panel, select the Panel Ch. No. item and press and hold the MENU key for 5 seconds. The Panel Ch. No. increases by 1 and the Panel On Time is reset to 0. At the same time, the Panel Cycle is also reset to 0.
Page 52
4. Troubleshooting Entering the EDID 1. Install the Winddc.exe program onto the PC. 2. Click the Winddc icon. 3. Select Open. 4. Select Port #1 5. Open a DDC file. *File Name “SM2493HMA.ddc” → Analog DDC “SM2493HMD.ddc” → Digital DDC “SM2493HMH.ddc”...
Page 53
4. Troubleshooting 7. Enter the Monitor S/N and press Enter. Enter for Analog, Digital and HDMI. 4-17...
6. Wiring Diagram 6-5. Connector Functions Connector Name Function Description VGA Signal Input Port. CN101 *Symptom: No RGB Signal. DVI Signal Input Port. CN102 *Symptom: No DVI Signal HDMI Signal Input Port CN703 *Symptom: No HDMI Signal. CN702 Function Key Terminal. CN400 It delivers the LVDS signal from the Main Board to the Panel.