1. Manuals
  2. Brands
  3. MAGINON Manuals
  4. IP Camera
  5. 40747
  6. Instruction manual

MAGINON 40747 Instruction Manual

Wlan surveillance camera
Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for MAGINON 40747

Summary of Contents for MAGINON 40747

  • Page 2: Warranty Details

    IP Security Camera Warranty Details The product is guaranteed to be free from defects in workmanship and parts for a period of 36 months (dependant on product) from the date of purchase. Defects that occur within this warranty period, under normal use and care, will be repaired, replaced or refunded at our discretion.The benefits conferred by this warranty are in addition to all rights and remedies in respect of the product that the consumer has under the Competition and Consumer Act 2010 and similar state and territory laws.

  • Page 3: Introduction

    Dear Customer, Congratulations on purchasing this high quality MAGINON® product. You have chosen a modern security camera with excellent technical features and accessories which are all especially easy to use. Please read all instructions carefully and attentively. Pay special attention to all safety instructions.

  • Page 4: Table Of Contents

    User data on delivery of IP Security Camera Note: admin“ of the camera. User name: admin Password: no Password presetted New Password: _______________________ 2. Table of contents Introduction 1. Contents of box 2. Table of contents 3. Hazard, safety and general warnings 4.
  • Page 5 5.4. Setting up the security camera 5.5. Internet access 6. Settings 6.1. Equipment status 6.2. Camera name 6.3. Date and time 6.4. User accounts 6.5. Network settings 6.6. Wireless settings 6.7. UPNP settings 6.8. DDNS settings 6.9. Email settings 6.10. FTP settings 6.11.

  • Page 6: Hazard, Safety And General Warnings

    3. Hazard, safety and general warnings Improper use or treatment of the camera and accessories poses a risk to you and others, and the camera may be damaged or destroyed. Therefore please read and observe strictly the following hazard, safety and general warnings. Intended use This security camera is intended to be used for monitoring indoor areas only.
  • Page 7 Hazard of electrocution in case of wet and humid conditions The camera and any supplied components may not be exposed to dripping or spray water. Containers filled with liquid, such as vases or glasses may also not be placed on or close to the camera Danger of fire and electrocution.
  • Page 8 Damage from heat – fi re hazard Do not leave camera and receiver in places that are susceptible to considerable increases in temperature (e.g. in a vehicle). The housing and internal parts may be damaged, which in turn could cause a fire. Do not wrap up camera and receiver or place on textiles.

  • Page 9: Preparations

    4. Preparations 4.1. Description of parts 1. MAGINON IP Security Camera IPC-1 6. Connector for alarm device 2. Mounting bracket 7. Assembly kit (not shown) 3. Network cable 8. Software CD (not shown) 4. AC adaptor 9. Instruction manual (not shown) 5.

  • Page 10: Views Of The Camera

    4.2. Views of the camera 90° 270° 1. Lens 5. Network socket (LAN) 2. Infrared LED 6. Alarm socket (in/out) 3. Sensor 7. Power supply socket (5V DC) 4. WiFi antenna 8. Reset button...

  • Page 11: Installing The Security Camera

    4.3. Installing the security camera Note: as this may result in interference. Should you experience picture interference, test on the lens. 4.3.1. Fitting stand to camera Hold the backplate of the foot against the surface of the chosen installation location and use a pencil to mark the surface with the location of the two drill holes.

  • Page 12: Completing The Camera Installation

    4.3.3. Completing the camera installation Screw the antenna plug onto the antenna socket on the rear side of the camera. Connect socket.

  • Page 13: Installing The Security Camera

    5. Installing the security camera 5.1. System requirements Operating system: the software contained on the CD supplied is only suitable for Windows systems. However, browser access may be used to set up and control the IP security camera via Mac OS, Linux or other operating systems also. Operating systems: Windows 2000 (SP 4), Windows XP (SP 2), Vista, 7 Processor:...

  • Page 14: Installing The Software

    5.3. Installing the software Insert the software CD supplied into your computer’s CD/DVD drive. The selection menu shown below should then appear. In the event that the menu does not launch automatically, go to the drive overview on your computer and click on the CD/DVD drive icon. To launch, double click on the CDMenu/CDMenu.exe program.

  • Page 15: Setting Up The Security Camera

    5.4. Setting up the security camera Make sure that the security camera is connected to both the router and the power source. Then open the program supra IPCam Confi g. Within the program, go to “Start search” to display a list of available security cameras. From the list, select the camera you want to set up or select.
  • Page 16 The camera is installed automatically on the network providing the “Use DCHP” option is activated and the router being used also supports DHCP (and this is activated). However you If the port being used by the security camera has to be changed, specify the new port number.

  • Page 17: Internet Access

    5.5. Internet access IP address. If a separate Internet address (domain) has been registered for the camera (see Section 6.8., DDNS Settings), this can be used to access the camera. You can have the public IP address sent to you by email. To do this, follow the instructions in Section 6.9., Email Settings.
  • Page 18 Start by opening your router’s port forwarding menu. In the example shown, two security cameras are connected to the router, one called IPCamera1 under local network address 192.168.1.110 and one called IPCamera2 under local network address 192.168.1.111. IPCamera1. TCP and UDP are both permitted protocols, however the only one required is TCP.

  • Page 19: Settings

    6. Settings The following sections will give you an overview of all possible settings for your IP security camera. Should problems arise, or settings need to be altered, during installation or use, you Bring up the camera on your Internet browser (see Section 7.1.) and log on via a user account with administrator’s permissions.

  • Page 20: Camera Name

    6.2. Camera name You can give the camera a name, for example in order to locate it more easily on the network “Save”. The camera name may consist of any characters and may be up to 20 characters long. The new camera name is accepted without the need to reboot the camera.

  • Page 21: Date And Time

    6.3. Date and time Specify here which time zone the camera is in and whether the date and time are to be updated automatically via a so called NTP server (time server). Current date and time: this shows the date and time as stored in the camera. This information is synched with the local system when the date and time settings are saved.

  • Page 22: User Accounts

    6.4. User accounts Up to 8 user accounts may be set up for the security camera. These user accounts are then used to access the security camera. account can neither be deleted nor have its administrator rights changed. It can merely be given a password.

  • Page 23: Network Settings

    6.5. Network settings To connect the security camera to an existing network or router, the network settings must be made. Use DHCP: if your network allows a new device (client) to be connected automatically, tick this box. All necessary data will then be drawn directly from the server or router. Web interface port: connections within a network are handled via so called ports allowing the server and each device (client) attached to it to work via diff erent ports sharing a common network address.
  • Page 24 In the event that automatic connection of new devices is not supported, please untick the which you should enter your network’s access data directly. The data required here can generally be obtained by looking at the network properties on your computer or by asking your network administrator IP address: (standard gateway), the camera’s address must be 192.168.1.x (where x can be any value...

  • Page 25: Wireless Settings

    6.6. Wireless settings In the event that the security camera is to be connected to a network via a wireless LAN (WiFi) you can enter the relevant settings here. Use WiFi: tick this box if you wish to connect wirelessly to the network. All subsequent required data regarding the wireless network is contained within the router or access point being used to control this network.
  • Page 26 Encryption: on wireless networks data is mainly encrypted in order to prevent access by third parties. Specify here which type of encryption is used by your wireless network. The setting “Non encrypted” means that data will be transmitted without encryption. If one of the “WEP”, “WPA”...

  • Page 27: Upnp Settings

    6.7. UPNP settings Universal Plug & Play (UPnP) allows diff erent manufacturers’ devices to be addressed over an IPbased network. Where UPnP is supported by the router and activated, the required Mark “Use UPNP” where UPNP is to be used for connecting to the security camera. By Click “Save”...

  • Page 28: Ddns Settings

    6.8. DDNS settings The security camera can be contacted via the IP address used by the router or server to connect to the Internet. Because, in many instance, the IP address of the Internet connection same address all the time. To this end, you can avail yourself of a DDNS server (DDNS = Dyna- http://supracam.net/ and choose “Register”.
  • Page 29 Once the camera has been registered successfully, switch to the DDNS settings. For “User name” and “Password”, enter the same data you entered when registering on the DDNS server. of one camera only, this is generally the user name, and in the case of more than one registered camera you should use the name you received upon registration.

  • Page 30: Email Settings

    6.9. Email settings In response to given events, the security camera can send an alarm message by email. This requires details to be entered on an email account from which emails can be sent. You can use a private email address or set up a separate email address specially for the security camera.
  • Page 31 Encryption: specify whether (and which type of ) encryption is used by the SMTP server. Requires authorisation: specify whether the SMTP server requires authorisation. If yes, tick this option and then enter the user name and password for the email account. Sender: enter the email address via which the alarm messages are to be sent.

  • Page 32: Ftp Settings

    6.10. FTP settings The security camera off ers you the opportunity to upload images to an FTP server, on either a one time or a regular basis. Enter here the required access data for an FTP server to be used for this purpose.
  • Page 33 Path: enter the path under which the images should be stored on the FTP server. Transfer mode: choose whether an active or passive FTP connection should be requested when transmitting. Upload at intervals: tick this option if you would like images from the security camera to be uploaded to the FTP server at regular intervals.

  • Page 34: Alarm Settings

    6.11. Alarm settings The security camera can issue alarm messages in a variety of situations. Specify here the conditions under which the camera is to issue an alarm message and what should be undertaken in the event of an alarm. Motion detection: tick this option to activate movement detection.
  • Page 35 Alarm level: specifies whether an alarm is triggered when there is no voltage at the alarm input (low setting) or when there is voltage (high setting). Report at digital output: where this option is activated, an alarm message is forwarded via the digital output as soon as it is in existence within the security camera.

  • Page 36: Head Settings

    6.12. Head settings This category can be used to make settings aff ecting the positioning of the camera head. Use Infrarot LEDs in darkness: if this option is activated, the infrared LEDs will be cut in as an additional light source in darkness. Fixed position on switching on: activate this option if the camera head should adopt a certain position when the security camera is switched on.

  • Page 37: Resetting

    Automatic speeds: specify, separately for up/down/left/right, how fast the camera head should move when being controlled automatically. Click “Save” to accept the changed settings. The new head settings are accepted without rebooting the camera 6.13. Resetting To reset the security camera to factory settings, click “Reset now”. Resetting takes approximately 1 minute.

  • Page 38: Using The Security Camera

    7. Using the security camera 7.1. Accessing the camera Begin by opening your browser program (Internet Explorer, Firefox, Opera, Google Chrome, Safari or similar). In the address line, enter the IP address of the security camera. If you wish to access the camera from a com- puter on the same local network, you may also enter the local network address.

  • Page 39: Controlling The Camera

    7.2. Controlling the camera The security camera is controlled by a variety of buttons and options. Below the camera head as well as some fundamental camera settings. Which buttons are available and which settings may be changed depend on the permissions granted to the user account.

  • Page 40: Storing Positions

    to pan automatically in a vertical or horizontal direction. This movement can be terminated again using the relevant button. In addition, the digital alarm control output can be enabled and disabled here. 7.2.2. Storing positions recall these directly. Click the buttons pertaining to 1, 2 or 3 in order to store the current camera position to this number.

  • Page 41: Camera Image Settings

    7.2.3. Camera image settings Use this view to specify the settings pertaining to the came image (picture). Resolution: here you can choose whether the security camera image is displayed in resolution of 640 x 480 pixels or 320 x 240 pixels. Light frequency: if the camera is being used in a space illuminated by fluorescent light, set the mains frequency of the local power circuit here (50 Hz or 60 Hz).

  • Page 42: Using The Camera Via Mobile Devices

    7.3. Using the camera via mobile devices The security camera image may also be accessed using mobile devices such as smartphones or tablet PCs. Use the mobile device’s browser to go to the camera’s homepage and use the Enter your user name and password (where relevant) and log onto the camera.
  • Page 43 The camera image will then appear complete with control buttons for moving the camera head. Further camera settings are not possible via mobile devices but may only be made using a PC based browser.

  • Page 44: Conformity

    8. Confi rmity This device has been tested in accordance with Part 15 of FCC Regulations, and it has been confi rmed that the limits applicable to Class B digital devices have been met. These limits are intended to off er reasonable protection against harmful sources of interference when installed in residential premises.

  • Page 45: Disposal

    For details please refer to the separate warranty card (enclosed). Before sending in your defective equipment, please contact our hotline. Manufacturer’s address: Service address: Schenker Australia Pty Ltd supra MAGINON® Service Foto-Elektronik-Vertriebs-GmbH P.O. Box 329 Denisstr. 28A Villawood, NSW 2163 67663 Kaiserslautern...

  • Page 46: Technical Specifi Cation

    11. Technical Specifi cation Model IPC-1 Image sensor 1/5" megapixel CMOS sensor, 640x480 pixels Lens F=2.4, f=3.6 mm, infrared lens Infrared light 9 infrared LEDs Night vision Minimum illumination 0.5 Lux (excl. LEDs) Image angle 60° Supported protocols HTTP, FTP, TCP/IP, SMTP, DHCP, DDNS, UPnP WiFi standards IEEE 802.11 b/g LAN connection...

  • Page 47: Glossary

    12. Glossary AC adaptor 7 Access camera 36 Email settings 28 Accessories 1, 7 Encryption 24 Administrator 20 Alarm connection 8 Alarm settings 32 Firewall 15 Alarm transmitter 7, 32 FTP settings 30 FTP server 30 Brightness 39 Hardware installation 11 Hazard warnings4ff Camera views 8 Head settings 34...
  • Page 48 Network connection 8 Tablet PC 40 Network data 13 Network set up 14, 21ff Time 19 Network cable 7, 11 Time zone 19 Network name 23 NTP server 19 Uploading images 30 UPnP 25 Operator 20 User accounts 20 Patrolling 37 Visitor 20 Port 14, 15ff , 21 Power supply 7...
  • Page 50 Foto-Elektronik-Vertriebs-GmbH 40747 Denisstr. 28A 12/2012 67663 Kaiserslautern 2615 1618 Germany...

Table of Contents