HP 525 Installation Manual
Wireless dual-radio 802.11ac access point
Hide thumbs
Also See for 525:
- Technical reference manual (146 pages) ,
- Supplementary manual (38 pages) ,
- Quick start manual (28 pages)
Related Manuals for HP 525
Summary of Contents for HP 525
-
Page 1: Access Point
HP 525 Wireless Dual-Radio 802.11ac Access Point Installation Guide Part number: 5998-5702 Document version: 5W100-20140820... - Page 2 The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an...
-
Page 3: Table Of Contents
Connecting the AP to a PoE power supply ········································································································· 11 Connecting the AP to the network ································································································································ 11 Support and other resources ····································································································································· 13 Contacting HP ································································································································································ 13 Subscription service ·············································································································································· 13 Related information ························································································································································ 13 ... -
Page 4: Preparing For Installation
Preparing for installation IMPORTANT: This installation guide shows you how to install and get started using the HP 525 Wireless Dual-Radio 802.11ac Access Point JG993A(AM), JG994A(WW), JG995A(JP), JG996A(IL), JG997A(8pack AM), JG998A(8pack WW), hereafter referred to as the HP 525.. Safety recommendations... -
Page 5: Accessories Provided With The Ap
LEDs." • Verify that cabling has been completed. The device supports 802.3af-compliant PoE. To achieve the best performance, HP recommends that • you use a GE connection to the power device. Record the MAC address and serial number of the AP (marked on the rear of the AP) for future use. -
Page 6: Installing The Ap
Installing the AP Figure 1 Installation flowchart Start Check before installation Ceiling mounting Mount the AP to a wall Determine the installation position T-rail mounting Mount the AP on a ceiling Attach the T-rail holder to the T-rail Mount the wall- Install the wall- mounting bracket to mounting bracket... - Page 7 Figure 2 Screw hole locations and sizes (in mm) Ø5.0 86.0 136.0 (1) Hook (2) Mounting hole (3) Clip (4) Mounting clip To mount the AP on a wall: Use the wall-mounting bracket as a template to mark the locations of the mounting holes on the bracket.
- Page 8 Insert a wall anchor into each mounting hole, and tap the wall anchor with a rubber hammer until it is flush with the wall surface as shown in Figure Figure 4 Inserting a wall anchor Align the holes in the wall-mounting bracket with the anchors and insert screws through the installation holes into the wall anchors as shown in Figure Adjust the position of the wall-mounting bracket and tighten the screws.
-
Page 9: Mounting The Ap To A T-Rail
Mount the AP on the hook on the wall-mounting bracket. See callout 1 in Figure Pull down the AP until it clicks into place. See callout 2 in Figure Figure 6 Mounting the AP to the wall mounting bracket Mounting the AP to a T-rail IMPORTANT: The width of the T-rail must be in the range of 16 mm to 28 mm (0.63 in to 1.10 in). - Page 10 Figure 7 Screw hole locations and sizes (in mm) Ø5.0 86.0 136.0 (1) Hook (2) Mounting hole (3) Clip (4) Mounting clip Figure 8 T-rail holder (1) T-rail clip (2) M3 screw nut (3) M4 screw nut (4) Clip holder (5) T-rail holder (6) Mounting hook (7) M4 ×...
- Page 11 Figure 9 Attaching the T-rail holder to the T-rail Tighten the four M3 × 8 screws on the two clip holders. Verify that the T-rail holder is attached to the T-rail. Hook the mounting clip (see callout 3 in Figure 10) of the wall-mounting bracket to the mounting hook (see callout 2 in Figure...
-
Page 12: Mounting The Ap On A Ceiling
Mounting the AP on a ceiling CAUTION: Verify that the AP is secured to the mounting bracket to avoid falloff. • Do not use this method to mount the AP to a location made of low-intensity materials such as a plaster •... -
Page 13: Connecting The Power Supply
Figure 12 Installing the mounting bracket to a ceiling (1) Nut, Length ( 4.5mm /0.18in ), Diameter ( 10mm (2) Washer / 0.39in) (3) Ceiling (4) Wall-mounting bracket (5) Hex-head bolt, Length ( 32mm / 1.26in ), Wrench (6) Hook size ( 6.85mm / 0.27in ), Thread size ( 3.91mm / 0.15in ) Connecting the power supply... -
Page 14: Connecting The Ap To A Poe Power Supply
Figure 13 Local power supply connection Connecting the AP to a PoE power supply CAUTION: Identify the marks for the network port and console port to avoid connection mistakes. When you apply 802.3af PoE power supply, connect one end of the network cable to the network port on the AP, and the other end to an Ethernet port on a PoE-capable device (for example, a PoE-capable Ethernet switch). - Page 15 Total Number of auto APs connected AP Profiles State : I = Idle, J = Join, JA = JoinAck, IL = ImageLoad C = Config, R = Run, KU = KeyUpdate, KC = KeyCfm -------------------------------------------------------------------------------- AP Name State Model Serial-ID -------------------------------------------------------------------------------- 525-WW CN12GTH123 -------------------------------------------------------------------------------- <AC>...
-
Page 16: Support And Other Resources
Related information Documents To find related documents, browse to the Manuals page of the HP Business Support Center website: http://www.hp.com/support/manuals For related documentation, navigate to the Networking section, and select a networking category. •... -
Page 17: Conventions
Conventions This section describes the conventions used in this documentation set. Command conventions Convention Description Boldface Bold text represents commands and keywords that you enter literally as shown. Italic Italic text represents arguments that you replace with actual values. Square brackets enclose syntax choices (keywords or arguments) that are optional. Braces enclose a set of required syntax choices separated by vertical bars, from which { x | y | ... - Page 18 Network topology icons Represents a generic network device, such as a router, switch, or firewall. Represents a routing-capable device, such as a router or Layer 3 switch. Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that supports Layer 2 forwarding and other Layer 2 features.
-
Page 19: Appendix A Chassis Views And Technical Specifications
Two 10/100/1000 Mbps copper Ethernet ports • A power supply port • NOTE: The device also provides a reset button. Figure 15 HP 525 ports 3 4 5 6 7 8 (1) 5G antenna port (2) 2.4G antenna port (3) Console port... -
Page 20: Weights And Dimensions
Table 1 HP 525 port description Port Standards and protocols Description • IEEE802.1 1b The antenna ports are provided for 2.4 GHz • IEEE802.1 1g 2.4G antenna port single-RF antennas. • IEEE802.1 1n • IEEE802.1 1a The antenna ports are provided for 5 GHz single-RF •... -
Page 21: Power Specifications
Power specifications AC voltage range Table 2 AC voltage range Power supply mode Voltage range Frequency Single-phase three-wire (V) 100 V to 240 V 50 or 60 Hz Power adapter specifications Item Description Input 100 VAC to 240 VAC Output +48V @ 0.63 A Storage media and memory specifications... -
Page 22: Appendix B Leds
Appendix B LEDs Table 3 LED description Mark Status Description The AP is booting. NOTE: Flashing green at 1 Hz When the AP operates as a fit AP, it is always in this state before it is registered to an AC. Slowly pulsing green Connections are present on the 2.4 GHz radios. -
Page 23: Appendix C Built-In Antenna
Appendix C Built-in antenna The HP 525 AP has a built-in dual-band MIMO antenna. Built-in cables connect the MIMO antenna to the 2.4 GHz and 5 GHz antenna ports of the AP. Table 4 Specifications Item Specification Standard IEEE 802.11n, 802.11ac and 802.11 a/b/g •... - Page 24 Figure 17 2.4 GHz radiation pattern in the vertical plane Figure 18 5.2 GHz radiation pattern in the horizontal plane...
- Page 25 Figure 19 5.2 GHz radiation pattern in the vertical plane...
-
Page 26: Index
Mounting the AP to a T-rail,6 Chassis views,16 Power specifications,18 Checking the installation site,1 Connecting the AP to the network,1 1 Connecting the power supply,10 Related information,13 Contacting HP,13 Conventions,14 Safety recommendations,1 Storage media and memory specifications,18 Installation preparation checklist,2...