Operation; Docking Station Installation; Vacuum Cleaner; Washing Your Filter - Dyson DC45 Operating Manual

vacuum cleaner

Please read the 'Important Safety Instructions' in this Dyson Operating Manual
before proceeding.

OPeraTIOn

• Ensure the appliance remains upright in use. Dirt and debris may be released if
it is turned upside down.
• Do not operate while checking for blockages.
• For domestic indoor and car use only. Do not use it whilst the car is in motion or
while driving.
• Take care if coming into contact with the carbon fibre brushes, as they may
cause minor skin irritation. Wash your hands after handling the brushes.

DOcKInG STaTIOn InSTallaTIOn

Use appropriate mounting hardware for your wall type and ensure that the
docking station is mounted securely. Ensure no pipe work (gas, water, air) or
electrical cables, wires or ductwork are located directly behind the mounting
area. The docking station must be mounted in accordance with regulations
and applicable codes/standards (state and local laws may apply). Dyson
recommends the use of protective clothing, eyeware and materials as necessary.
carPeTS Or HarD FlOOrS
• Before vacuuming your flooring, rugs and carpets, check the manufacturer's
recommended cleaning instructions.
• The brush bar on the appliance can damage certain carpet types and floors.
Some carpets will fuzz if a rotating brush bar is used when vacuuming. If this
happens, we recommend vacuuming without the motorised floor tool and
consulting with your flooring manufacturer.
• Before vacuuming highly polished floors, such as wood or lino, first check that
the underside of the floor tool and its brushes are free from foreign objects that
could cause marking.
lOOKInG aFTer YOur DYSOn aPPlIance
• Do not carry out any maintenance or repair work other than that shown in this
Dyson Operating Manual, or advised by the Dyson Helpline.
• Only use parts recommended by Dyson. If you do not this could invalidate
your guarantee.
• Store the appliance indoors. Do not use or store it below 0°C (32°F). Ensure the
appliance is at room temperature before operating.
• Clean the appliance only with a dry cloth. Do not use any lubricants, cleaning
agents, polishes or air fresheners on any part of the appliance.
• If used in a garage, always wipe the base plate and ball with a dry cloth after
vacuuming to clean off any sand, dirt, or pebbles that could damage
delicate floors.
vacuumInG
• Do not use without the clear bin and filter in place.
• Fine dirt such as plaster dust or flour should only be vacuumed in very
small amounts.
• Do not use the appliance to pick up sharp hard objects, small toys, pins, paper
clips, etc. They may damage the appliance.
• When vacuuming, certain carpets may generate small static charges in the
clear bin or nozzle. These are harmless and are not associated with the mains
electricity supply. To minimise any effect from this, do not put your hand or
insert any object into the clear bin unless you have first emptied it and cleaned it
with a damp cloth (see 'Cleaning the clear bin').
• Use extra care when cleaning on stairs.
• Do not rest the appliance on chairs, tables, etc.
• Do not press down on the nozzle with excessive force when using the appliance
as this may cause damage.
• Do not leave the cleaner head in one place on delicate floors.
• On waxed floors the movement of the cleaner head may create an uneven
lustre. If this happens, wipe with a damp cloth, polish the area with wax, and
wait for it to dry.
DIaGnOSTIcS – aPPlIance
Less than one minute of charge remaining/fully discharged.
Too cold/too hot - do not use.
emPTYInG THe clear BIn
• Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.
• Ensure the appliance is disconnected from the charger before emptying the
clear bin.
12
• To release the dirt, push the red button at the side of the clear bin as shown.
• To minimise dust/allergen contact when emptying, encase the clear bin tightly
in a plastic bag and empty. Remove the clear bin carefully and seal bag tightly,
dispose as normal.
• To make emptying the clear bin easier, it is advisable to remove the wand and
floor tool.
cleanInG THe clear BIn
• Ensure the appliance is disconnected from the charger before removing the
clear bin.
• Be careful not to pull the 'ON' trigger.
• Remove the wand and floor tool.
• To remove the clear bin, push the red button at the side of the clear bin as you
would when emptying the clear bin. This will expose the red release button on
the underside of the handle. Press this to release the clear bin.
• Remove the clear bin carefully.
• Clean the clear bin with a damp cloth only.
• Ensure the clear bin is completely dry before replacing.
• Do not use detergents, polishes or air fresheners to clean the clear bin.
• Do not put the clear bin in a dishwasher.
• Clean the cyclone shroud with a dry cloth or dry brush to remove lint
and dust.
• To replace the clear bin, fit the tab on the rim of the cyclone shroud into the
aperture on the inside of the top of the clear bin. Push the clean bin up and in.
It will click into place.
• Close the base of the clear bin.

WaSHInG YOur FIlTer

• Ensure the appliance is disconnected from the charger before removing the filter.
• Your appliance has one washable filter, located as shown.
• Press the 'Filter' button so you can remove the cyclone and clear bin unit.
• Check and wash the filter regularly according to instructions to maintain
performance.
• The filter may require more frequent washing if vacuuming fine dust or if used
mainly in 'HIGH CONSTANT SUCTION' mode.
• Wash the filter with cold water only. Do not use detergents.
• Do not put the filter in a dishwasher, washing machine, tumble dryer, oven,
microwave or near a naked flame.
• IMPORTANT: After washing please leave at least 12 hours to dry completely
before refitting.
• Place the dry filter into the recess of the handle.
• Fit the base of the handle into the aperture on the base of the cyclone and clear
bin unit. Push both halves together until the 'Filter' button engages and locks
into place.
lOOKInG FOr BlOcKaGeS
• Ensure the appliance is disconnected from the charger before looking for
blockages.
• Do not operate while checking for blockages. Failure to do so could result in
personal injury.
• Beware of sharp objects when checking for blockages.
• Refit all parts securely before using.
• Clearing blockages is not covered by your guarantee.
• If you cannot clear an obstruction you may need to remove the brush bar. Use
a coin to unlock the fastener marked with a padlock. Remove the obstruction.
Replace the brush bar and secure it by locking the fastener. Ensure it is fixed
firmly before operating the appliance.
• Take care if coming into contact with the carbon fibre brushes, as they may
cause minor skin irritation. Wash your hands after handling the brushes.
clearInG BlOcKaGeS – THermal cuT-OuT
• This appliance is fitted with an automatically resetting thermal cut-out.
• Large items may block the tools or nozzle. If any part becomes blocked the
appliance may overheat and automatically cut-out.
• Leave to cool down for 1-2 hours before checking the filter or for blockages.
• Ensure the appliance is disconnected from the charger before looking for
blockages. Failure to do so could result in personal injury.
• Clear any blockage before restarting.
• Refit all parts of the appliance securely before using.
• Clearing blockages is not covered by your guarantee.
cHarGInG anD STOrInG
• This appliance will switch 'OFF' if the battery temperature is below 3°C. This
is designed to protect the motor and battery. Do not charge the appliance and
then move it to an area with a temperature below 3°C for storage purposes.
• To help prolong battery life, avoid recharging immediately after a full discharge.
Allow to cool for a few minutes.
• Avoid using the appliance with the battery flush to a surface. This will help it run
cooler and prolong battery run time and life.