Download Print this page

KitchenAid KSDG950ESS Installation Instructions Manual page 23

Slide-in downdraft ranges
Hide thumbs

Advertisement

Table of Contents
6. Unscrew the metal cover and unscrew the blue regulator
cap. Keep the washer in place.
A
A. Metal cover
B. Washer
C. Blue regulator cap
7. Flip the blue regulator cap over and screw it back into
the metal cover.
A
A. Natural gas position
B. LP gas position
8. Screw the metal cover securely back into place.
Do not overtighten.
To Convert Surface Burners (Natural Gas to LP Gas)
1. If installed, remove the burner grates.
2. Remove the burner caps.
3. Remove the burner base.
A
A. Igniter electrode
B. Burner cap
C. Gas tube opening
D. Burner base
4. Apply masking tape to the end of a
to help hold the gas orifice spud in the nut driver while
changing it. Press nut driver down onto the gas orifice spud
and remove by turning it counterclockwise and lifting out.
Set gas orifice spud aside.
B
A
C
A. Igniter electrode
B. Orifice spud
A
B
C
B
B
C
D
" (7 mm) nut driver
9
32
D
C. Orifice spud holder
D. Screws
5. Remove the orifice spuds shipped in the literature package
in the oven. Gas orifice spuds are stamped with a number,
marked with 1 or 2 color dots, and have a groove in the hex
area. Replace the Natural gas orifice spud with the correct
LP gas orifice spud.
A. LP groove
Refer to the following chart for correct LP gas orifice spud
ratings and to spud holder card for proper placement.
LP Gas Orifice Spud Chart for Surface Burners
Burner
Rating/Type
Color
Size (mm)
15,000 BTU/
Silver
1.05
Stacked*
Black/
0.32
Orange
14,200
Silver
1.05
BTU/ Ultra/
Stacked*
8,000 BTU/
Red/
0.85
Semi
Orange
5,000 BTU/
Red/
0.65
Auxi
Blue
1,200 BTU/
Black/
0.32
Stacked/
Orange
Simmer*
*Not in all kits/models.
NOTE: Refer to the model/serial/rating plate located on the
oven frame behind the top right-hand side of the oven door
for proper sizing of spuds for each burner location.
6. Place Natural gas orifice spuds in the orifice spud bag.
IMPORTANT: Keep the Natural gas orifice spuds in case
of reinstallation with Natural gas.
7. Replace the burner base.
8. Replace burner cap.
9. Repeat steps 1 to 7 for the remaining burners.
Complete Installation (Natural Gas to LP Gas)
1. Refer to the "Make Gas Connection" section for proper
connection of the range to the gas supply.
2. Refer to the "Electronic Ignition System" section for proper
burner ignition and operation.
3. Refer to the "Adjust Flame Height" section for burner flame
adjustments.
IMPORTANT: You may have to adjust the low setting for
each cooktop burner.
Checking for proper cooktop burner flame is very important.
Natural gas flames do not have yellow tips.
4. Refer to "Complete Installation" in the "Installation
Instructions" section of this manual to complete this
procedure.
IMPORTANT: Make sure to save the orifices that have
just been replaced in the conversion.
A
ID
Number
Placement
L105
LF
L32
L105
LF/RF
L85
RR/CTR
L65
LR
L32
LF (Simmer)
23

Hide quick links:

Advertisement

Table of Contents
loading

  Also See for KitchenAid KSDG950ESS

  Related Manuals for KitchenAid KSDG950ESS

This manual is also suitable for:

Kseg950ess-ss